• 11/30235009 DC : 0

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    BS EN 13852-1 - CRANES - OFFSHORE CRANES - PART 1: GENERAL PURPOSE OFFSHORE CRANES

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-10-2013

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 List of significant hazards
    5 Safety requirements and/or protective measures
    6 Verification of the safety requirements and/or
      protective measures
    7 Information for use
    Annex A (informative) - Selection of a suitable set
            of crane standards for a given application
    Annex B (normative) - Determination of factors
    Annex C (normative) - Environmental influences
    Annex D (normative) - Failure mode analysis
    Annex E (normative) - Material selection
    Annex F (normative) - Control station instrumentation
    Annex G (normative) - Wire rope safety factors
    Annex H (normative) - Slewing bearings
    Annex I (normative) - Requirements for brakes
    Annex J (normative) - Ranking of safety systems
    Annex K (normative) - Required performance levels (PLr) for
            SRP/CS according to EN ISO 13849-1:2008
    Annex L (informative) - Typical general-purpose offshore
            cranes and terminology
    Annex M (normative) - Design excursion envelopes
    Annex N (normative) - Noise test code
    Annex O (normative) - Equipment for use in a hazardous area
    Annex ZA (informative) - Relationship between this
             European Standard and the Essential
             Requirements of EU Directive 2006/42/EC

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee MHE/3/10
    Document Type Draft
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 1127-1:2011 Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology
    EN 12385-2:2002+A1:2008 Steel wire ropes - Safety - Part 2: Definitions, designation and classification
    EN 12385-4:2002+A1:2008 Steel wire ropes - Safety - Part 4: Stranded ropes for general lifting applications
    CEN/TS 13001-3-1:2004/AC:2006 CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES
    EN 894-3:2000+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators
    EN 13557:2003+A2:2008 Cranes - Controls and control stations
    EN 982:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
    ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
    EN 12385-1:2002+A1:2008 Steel wire ropes - Safety - Part 1: General requirements
    EN 10025-4:2004 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
    ISO 12480-1:1997 Cranes Safe use Part 1: General
    EN 12644-2:2000+A1:2008 Cranes - Information for use and testing - Part 2: Marking
    EN 60079-1:2014 Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
    ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
    ISO 9374-4:1989 Cranes Information to be provided Part 4: Jib cranes
    EN 61310-2:2008 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
    EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
    EN 14502-1:2010 Cranes - Equipment for the lifting of persons - Part 1: Suspended baskets
    EN 12385-3:2004+A1:2008 Steel wire ropes - Safety - Part 3: Information for use and maintenance
    EN 60079-15:2010 Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
    EN ISO 14121-1:2007 Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007)
    EN 13463-1:2009 Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements
    EN 13135-2:2004+A1:2010 Cranes - Equipment - Part 2: Non-electrotechnical equipment
    ISO 12478-1:1997 Cranes Maintenance manual Part 1: General
    EN 61310-3:2008 Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators
    EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
    ISO 8566-1:2010 Cranes Cabins and control stations Part 1: General
    ISO 9927-1:2013 Cranes — Inspections — Part 1: General
    EN 13586:2004+A1:2008 Cranes - Access
    EN ISO 7731:2008 Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003)
    EN 50017:1998 Electrical apparatus for potentially explosive atmospheres - Powder filling "q"
    EN 614-1:2006+A1:2009 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
    EN 13411-3:2004+A1:2008 Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing
    EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
    EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
    EN 12644-1:2001+A1:2008 Cranes - Information for use and testing - Part 1: Instructions
    ISO 9374-1:1989 Cranes Information to be provided Part 1: General
    EN 13411-7:2006+A1:2008 Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket
    EN 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
    EN ISO 11201:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)
    EN 60079-11:2012 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
    EN 13001-2:2014 Crane safety - General design - Part 2: Load actions
    EN 13135-1:2003+A1:2010 Cranes - Equipment - Part 1: Electrotechnical equipment
    EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
    EN 60079-25:2010/AC:2013 EXPLOSIVE ATMOSPHERES - PART 25: INTRINSICALLY SAFE ELECTRICAL SYSTEMS (IEC 60079-25:2010)
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    EN 13001-1:2015 Cranes - General design - Part 1: General principles and requirements
    EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
    EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
    EN 842:1996+A1:2008 Safety of machinery - Visual danger signals - General requirements, design and testing
    EN 61000-6-4:2007/A1:2011 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS
    EN 10025-5:2004 Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
    EN 13411-4:2011 Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing
    EN 13411-6:2004+A1:2008 Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket
    EN 10204:2004 Metallic products - Types of inspection documents
    ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
    CEN/TS 13001-3-5:2010 Cranes - General design - Part 3-5: Limit states and proof of competence of forged hooks
    EN ISO 12100-2:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
    EN 10025-2:2004/AC:2005 HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS
    EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
    EN 60079-14:2014/AC:2016 EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016)
    EN 10083-2:2006 Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels
    EN 983:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
    EN 10025-6:2004+A1:2009 Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
    ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
    ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
    EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
    EN 50015:1998 Electrical apparatus for potentially explosive atmospheres - Oil immersion "o"
    EN 1005-3:2002+A1:2008 Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation
    ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
    EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
    ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
    EN 10025-3:2004 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
    ISO/TR 11688-2:1998 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
    EN 61310-1:2008 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
    IEC 61000-6-2 : 3.0:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS
    ISO 12482-1:1995 Cranes Condition monitoring Part 1: General
    ISO 11201:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
    CEN/TS 13001-3-2:2008 Cranes - General design - Part 3-2: Limit states and proof of competence of wire ropes in reeving systems
    EN 1993-1-1:2005/A1:2014 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
    EN 60079-2:2014/AC:2015 EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective