Skip to content
Please enter a keyword to search

  • 16/30312922 DC : 0

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    BS ISO 18888 - GAS TURBINE COMBINED CYCLE POWER PLANTS THERMAL PERFORMANCE TESTS

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-10-2017

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Test boundary
    5 Symbols and units
    6 Preparation for test
    7 Execution of test
    8 Calculation of results for absolute test
    9 Part load tests
    10 Calculation of results for comparative test
    11 Test report
    Annex A (informative) - Typical secondary
            variables
    Annex B (informative) - Numerical examples of
            uncertainty calculation
    Annex C (normative) - Procedure for power factor
            conversion
    Bibliography

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee MCE/16
    Document Type Draft
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
    ISO 10715:1997 Natural gas — Sampling guidelines
    ISO 6976:2016 Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition
    ISO 3675:1998 Crude petroleum and liquid petroleum products Laboratory determination of density Hydrometer method
    ISO 12242:2012 Measurement of fluid flow in closed conduits Ultrasonic transit-time meters for liquid
    ISO 3977-1:1997 Gas turbines — Procurement — Part 1: General introduction and definitions
    ISO 11086:1996 Gas turbines — Vocabulary
    ASTM D 4868 : 2017 : REDLINE Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels
    ISO 3977-9:1999 Gas turbines Procurement Part 9: Reliability, availability, maintainability and safety
    ISO 6975:1997 Natural gas — Extended analysis — Gas-chromatographic method
    ISO 2533:1975 Standard Atmosphere
    ISO 6974-3:2000 Natural gas Determination of composition with defined uncertainty by gas chromatography Part 3: Determination of hydrogen, helium, oxygen, nitrogen, carbon dioxide and hydrocarbons up to C8 using two packed columns
    DIN 51900-1:2000-04 Determining the gross calorific value of solid and liquid fuels using the bomb calorimeter, and calculation of net calorific value - Part 1: General information
    ISO 5167:1980 Measurement of fluid flow by means of orifice plates, nozzles and Venturi tubes inserted in circular cross-section conduits running full
    ISO 12185:1996 Crude petroleum and petroleum products — Determination of density — Oscillating U-tube method
    ISO 2314:2009 Gas turbines — Acceptance tests
    ISO 6817:1992 Measurement of conductive liquid flow in closed conduits Method using electromagnetic flowmeters
    IEC 60751:2008 Industrial platinum resistance thermometers and platinum temperature sensors
    ISO 10790:2015 Measurement of fluid flow in closed conduits Guidance to the selection, installation and use of Coriolis flowmeters (mass flow, density and volume flow measurements)
    ISO 6974-1:2012 Natural gas — Determination of composition and associated uncertainty by gas chromatography — Part 1: General guidelines and calculation of composition
    ISO 17089-1:2010 Measurement of fluid flow in closed conduits - Ultrasonic meters for gas Part 1: Meters for custody transfer and allocation measurement
    ISO 12213-2:2006 Natural gas Calculation of compression factor Part 2: Calculation using molar-composition analysis
    ISO 20765-2:2015 Natural gas Calculation of thermodynamic properties Part 2: Single-phase properties (gas, liquid, and dense fluid) for extended ranges of application
    ASTM D 1945 : 2014 : REDLINE Standard Test Method for Analysis of Natural Gas by Gas Chromatography
    ISO 20765-1:2005 Natural gas Calculation of thermodynamic properties Part 1: Gas phase properties for transmission and distribution applications
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective