IEC 62246-1:2015
|
Reed switches - Part 1: Generic specification |
OIML D 11 : 2013
|
GENERAL REQUIREMENTS FOR MEASURING INSTRUMENTS - ENVIRONMENTAL CONDITIONS |
ISO 5168:2005
|
Measurement of fluid flow — Procedures for the evaluation of uncertainties |
EN 60079-0:2012/A11:2013
|
EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
EN 62246-1:2015
|
Reed switches - Part 1: Generic specification |
ISO 3:1973
|
Preferred numbers Series of preferred numbers |
ISO 6708:1995
|
Pipework components Definition and selection of DN (nominal size) |
EN 12405 : 2002
|
GAS METERS - GAS-VOLUME ELECTRONIC CONVERSION DEVICES |
EN ISO 6708:1995
|
Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
EN 60079-11:2012
|
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
IEC 60079-11:2011
|
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
EN 60947-5-6:2000
|
Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR) |
EN ISO 5167-1:2003
|
Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
EN 437:2003+A1:2009
|
Test gases - Test pressures - Appliance categories |
EN ISO 9001:2015
|
Quality management systems - Requirements (ISO 9001:2015) |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV
|
Degrees of protection provided by enclosures (IP Code) |
EN 22768-1:1993
|
General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989) |
ISO 5167-1:2003
|
Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
EN 334:2005+A1:2009
|
Gas pressure regulators for inlet pressures up to 100 bar |
IEC 60079-0:2011
|
Explosive atmospheres - Part 0: Equipment - General requirements |
EN 10204:2004
|
Metallic products - Types of inspection documents |
ISO 9001:2015
|
Quality management systems — Requirements |
ISO 7005-1:2011
|
Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
EN 60529:1991/AC:2016-12
|
DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
EN 60068-2-30:2005
|
Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
IEC 60947-5-6:1999
|
Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR) |
EN 60730-1:2016
|
Automatic electrical controls - Part 1: General requirements |
ISO/IEC Guide 98-3:2008
|
Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) |
IEC 60730-1:2013+AMD1:2015 CSV
|
Automatic electrical controls - Part 1: General requirements |
IEC 60068-2-30:2005
|
Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |