Skip to content
Please enter a keyword to search

  • BS EN 200:2008

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Sanitary tapware. Single taps and combination taps for water supply systems of type 1 and type 2. General technical specification

    Available format(s):  Hardcopy, PDF

    Superseded date:  04-01-2024

    Language(s):  English

    Published date:  31-03-2009

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Designation
    4 Marking and identification
    5 Materials
    6 Dimensional characteristics
    7 Sequence of testing
    8 Leaktightness characteristics
    9 Pressure resistance characteristics - mechanical performance
       under pressure
    10 Hydraulic characteristics
    11 Mechanical strength characteristics - torsion test for
       operating mechanism
    12 Mechanical endurance characteristics
    13 Backflow protection
    14 Acoustic characteristics
    Annex A (informative) - Pressure take-off tee
    Bibliography

    Abstract - (Show below) - (Hide below)

    Pertains to draw-off taps (single taps and combination taps) for use with sanitary appliances installed in rooms used for bodily hygiene (cloakrooms, bathrooms etc.) and in kitchens, i.e. for use with baths, wash basins, bidets, showers and sinks.

    General Product Information - (Show below) - (Hide below)

    Committee B/504/-/8
    Development Note Supersedes 83/14570 DC (09/2005) Supersedes BS 5412(1996), which is declared obsolescent. (01/2009)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    11/30228295 DC : 0 BS 8558 - GUIDE TO THE DESIGN, INSTALLATION, TESTING, OPERATION AND MAINTENANCE OF SERVICES SUPPLYING WATER FOR DOMESTIC USE WITHIN BUILDINGS AND THEIR CURTILAGES - COMPLEMENTARY GUIDANCE TO BS EN 806
    BS 6465-3:2006 Sanitary installations Code of practice for the selection, installation and maintenance of sanitary and associated appliances
    BS 6700:1997 Specification for design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages
    BS 6700(2006) : 2006 DESIGN, INSTALLATION, TESTING AND MAINTENANCE OF SERVICES SUPPLYING WATER FOR DOMESTIC USE WITHIN BUILDINGS AND THEIR CURTILAGES - SPECIFICATION
    11/30218883 DC : 0 BS 8542 - CALCULATING WATER CONSUMPTION IN NON-DOMESTIC BUILDINGS - CODE OF PRACTICE
    BS 8542:2011 Calculating domestic water consumption in non-domestic buildings. Code of practice
    BS 5412:1996 Specification for low-resistance single taps and combination tap assemblies (nominal size ½ and ¾) suitable for operation at PN 10 max. and a minimum flow pressure of 0.01 MPa (0.1 bar)
    BS 8558:2011 Guide to the design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages. Complementary guidance to BS EN 806

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 3822-1:1999 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 1: Method of measurement
    EN 246:2003 Sanitary tapware - General specifications for flow rate regulators
    EN 1112:2008 Sanitary tapware - Shower outlets for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification
    EN 1254-2:1998 Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes
    EN 1113:2015 SANITARY TAPWARE - SHOWER HOSES FOR SANITARY TAPWARE FOR WATER SUPPLY SYSTEMS OF TYPE 1 AND TYPE 2 - GENERAL TECHNICAL SPECIFICATION
    ISO 3822-4:1997 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 4: Mounting and operating conditions for special appliances
    EN 1717:2000 Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow
    EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
    EN ISO 3822-4:1997 Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 4: Mounting and operating conditions for special appliances
    EN 14506:2005 Devices to prevent pollution by backflow of potable water - Automatic diverter - Family H, type C
    EN ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003)
    ISO 3822-2:1995 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 2: Mounting and operating conditions for draw-off taps and mixing valves
    ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements
    EN ISO 3822-1:1999/A1:2008 ACOUSTICS - LABORATORY TESTS ON NOISE EMISSION FROM APPLIANCES AND EQUIPMENT USED IN WATER SUPPLY INSTALLATIONS - PART 1: METHOD OF MEASUREMENT
    EN ISO 3822-2:1995 Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 2: Mounting and operating conditions for draw-off taps and mixing valves (ISO 3822-2:1995)
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    EN 248:2002 Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective