BS 7903:1997
|
Guide to selection and use of gully tops and manhole covers for installation within the highway |
BS 7861-1:1996
|
Strata reinforcement support system components used in coal mines Specification for rockbolting |
BS 3892-3:1997
|
Pulverized-fuel ash Specification for pulverized-fuel ash for use in cementitious grouts |
PD 6584:1995
|
Model for a supplier quality assurance assessment questionnaire |
DEFSTAN 59-100(PT1)/3(1995) : 1995
|
FUSE-HOLDERS, CARRIERS AND BASES ELECTRICAL FUSE (BLOCK AND EXTRACTOR POST TYPES) - PART 1: SPECIFICATIONS |
BS 7924:1999
|
Code of practice for the repair and overhaul of certified electrical apparatus intended for use in mines susceptible to firedamp |
BS EN 729-2:1995
|
Quality requirements for welding. Fusion welding of metallic materials Comprehensive quality requirements |
BS EN 1655:1997
|
Copper and copper alloys. Declarations of conformity |
BS 7000-2:1997
|
Design management systems Guide to managing the design of manufactured products |
BS 8701:2016
|
Full ring ovalization test for determining the susceptibility to cracking of linepipe steels in sour service. Test method |
09/30093258 DC : DRAFT JUNE 2009
|
BS 8006-1 - CODE OF PRACTICE FOR STRENGTHENED/REINFORCED SOILS AND OTHER FILLS |
BS 7865:1997
|
Specification for steel electrical conductor rail for railway motive power supply |
DEFSTAN 02-855/1(2004) : 2004
|
ELECTRON BEAM WELDING OF MARINE COMPONENTS - CATEGORY 2 |
BS CECC 00108:1996
|
Rule of Procedure 8. Attestation of conformity. The CECC Mark and conditions of use, certificates of approval and procedures for the attestation of conformity |
BS 500:2000
|
Steel sleepers |
BS 5911-200:1994
|
Precast concrete pipes, fittings and ancillary products Specification for unreinforced and reinforced manholes and soakaways of circular cross section |
BS 4275:1997
|
Guide to implementing an effective respiratory protective device programme |
BS 5534-1:1997
|
Code of practice for slating and tiling Design |
BS QC 001002-3:1997
|
Rules of procedure of the IEC quality assessment system for electronic components (IECQ) Approval procedures, including a new clause on technology approval |
BS CECC 00806:1997
|
Harmonized system of quality assessment for electronic components. Guide to total quality management (TQM) for CECC approved organizations |
BS 123000:2001
|
System of quality assessment. Generic specification. Printed boards |
BS 7738-1:1994
|
Specification for information systems products using SSADM (Structured Systems Analysis and Design Method) Implementation of SSADM version 4 |
BS HB10192(2001) : 2001
|
GUIDE TO BS EN 13549 - CLEANING SERVICES, BASIC REQUIREMENTS AND RECOMMENDATIONS FOR QUALITY MEASURING SYSTEMS |
07/30163374 DC : DRAFT MAR 2007
|
BS 7861-1 - STRATA REINFORCEMENT SUPPORT SYSTEM COMPONENTS USED IN COAL MINES - PART 1: SPECIFICATION FOR ROCKBOLTING |
BS EN 50103:1996
|
Guidance on the application of EN 29001 and EN 46001 and of EN 29002 and EN 46002 for the active (including active implantable) medical device industry |
PD 1002:1997
|
A guide to cabling in private telecommunications systems |
EEMUA 197 : 1999
|
SPECIFICATION FOR FABRICATION OF NON-PRIMARY STRUCTURAL STEELWORK FOR OFFSHORE INSTALLATIONS |
BS 4660:2000
|
Thermoplastics ancillary fittings of nominal sizes 110 and 160 for below ground gravity drainage and sewerage |
EN 100114-1 : 1996
|
RULE OF PROCEDURE - QUALITY ASSESSMENT PROCEDURES - PART 1: CECC REQUIREMENTS FOR THE APPROVAL OF AN ORGANIZATION |
BS CECC 00114-0:1994
|
Rule of procedure 14. Quality assessment procedures An introduction to the types of approval available under the CECC system |
BS 5882:1996
|
Specification for a total quality assurance programme for nuclear installations |
BS M 78:1995
|
Aircraft de-icing/anti-icing non-Newtonian fluids, ISO type II |
BS EN ISO 9000-1:1994
|
Quality management and quality assurance standards Guidelines for selection and use |
BS EN 729-3:1995
|
Quality requirements for welding. Fusion welding of metallic materials Standard quality requirements |
BS EN 639:1995
|
Common requirements for concrete pressure pipes including joints and fittings |
BS EN 729-4:1995
|
Quality requirements for welding. Fusion welding of metallic materials Elementary quality requirements |
BS EN 1092-2:1997
|
Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, PN designated Cast iron flanges |
BS 5750-4:1994
|
Quality systems Guide to the use of BS EN ISO 9001 \'Model for quality assurance in design, development, production, installation and servicing (Formerly BS 5750:Part 1)\', BS EN ISO 9002 \'Model for quality assurance in production, installation and servicing (Formerly BS 5750:Part 2)\' and BS EN ISO 9003 \'Model for quality assurance in final inspection and test (Formerly BS 5750:Part 3)\' |
EN ISO 9000-1 : 1994
|
QUALITY MANAGEMENT AND QUALITY ASSURANCE STANDARDS - PART 1: GUIDELINES FOR SELECTION AND USE (ISO 9000-1:1994) |
EN 639:1994
|
Common requirements for concrete pressure pipes including joints and fittings |
16/30319903 DC : 0
|
BS 8701 - FULL RING OVALIZATION TEST FOR DETERMINING THE SUSCEPTIBILITY TO CRACKING OF LINEPIPE STEELS IN SOUR SERVICE - TEST METHOD |
BS EN ISO 8402:1995
|
Quality management and quality assurance. Vocabulary |
BS 8006:1995
|
Code of practice for strengthened/reinforced soils and other fills |
DD ENV 10080:1996
|
Steel for the reinforcement of concrete. Weldable ribbed reinforcing steel B500. Technical delivery conditions for bars, coils and welded fabric |
BS EN 100114-1:1997
|
Rule of Procedure 14. Quality assessment procedures CECC requirements for the approval of an organization |
BS EN 729-1:1995
|
Quality requirements for welding. Fusion welding of metallic materials Guidelines for selection and use |