Skip to content
Please enter a keyword to search

  • BS ISO 4046-5:2016

    Current The latest, up-to-date edition.

    Paper, board, pulps and related terms. Vocabulary Properties of pulp, paper and board

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  31-03-2016

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    Scope
    Terms and definitions
    Bibliography

    Abstract - (Show below) - (Hide below)

    Specifies terms related to properties of pulp, paper and board, in both English and French.

    General Product Information - (Show below) - (Hide below)

    Committee PAI/11
    Development Note Supersedes 00/123974 DC (01/2003) Together with BS ISO 4046-1, BS ISO 4046-2, BS ISO 4046-3 and BS ISO 4046-4, supersedes BS 3203(1979). (01/2003)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 5651:1989 Paper, board and pulps Units for expressing properties
    ISO 13821:2002 Corrugated fibreboard Determination of edgewise crush resistance Waxed edge method
    ISO 1974:2012 Paper — Determination of tearing resistance — Elmendorf method
    ISO 10241:1992 International terminology standards Preparation and layout
    ISO 4094:2005 Paper, board and pulps International calibration of testing apparatus Nomination and acceptance of standardizing and authorized laboratories
    ISO 9932:1990 Paper and board Determination of water vapour transmission rate of sheet materials Dynamic sweep and static gas methods
    ISO 8254-1:2009 Paper and board Measurement of specular gloss Part 1: 75 degree gloss with a converging beam, TAPPI method
    ISO 5629:1983 Paper and board Determination of bending stiffness Resonance method
    ISO 11108:1996 Information and documentation — Archival paper — Requirements for permanence and durability
    ISO 8226-1:1994 Paper and board Measurement of hygroexpansivity Part 1: Hygroexpansivity up to a maximum relative humidity of 68 %
    ISO 7263:2011 Corrugating medium Determination of the flat crush resistance after laboratory fluting
    ISO 11556:2005 Paper and board — Determination of curl using a single vertically suspended test piece
    ISO 5351-1:1981 Cellulose in dilute solutions Determination of limiting viscosity number Part 1: Method in cupri-ethylene-diamine (CED) solution
    ISO 1924-1:1992 Paper and board Determination of tensile properties Part 1: Constant rate of loading method
    ISO 5626:1993 Paper Determination of folding endurance
    ISO 699:2015 Pulps Determination of alkali resistance
    ISO 2471:2008 Paper and board — Determination of opacity (paper backing) — Diffuse reflectance method
    ISO 302:2015 Pulps Determination of Kappa number
    ISO 638:2008 Paper, board and pulps Determination of dry matter content Oven-drying method
    ISO 5637:1989 Paper and board Determination of water absorption after immersion in water
    ISO 9706:1994 Information and documentation — Paper for documents — Requirements for permanence
    ISO 1762:2015 Paper, board and pulps Determination of residue (ash) on ignition at 525 degrees C
    ISO 692:1982 Pulps Determination of alkali solubility
    ISO 9895:2008 Paper and board — Compressive strength — Short-span test
    ISO 15361:2000 Pulps Determination of zero-span tensile strength, wet or dry
    ISO 3783:2006 Paper and board — Determination of resistance to picking — Accelerated speed method using the IGT-type tester (electric model)
    ISO 776:2011 Pulps — Determination of acid-insoluble ash
    ISO 2758:2014 Paper Determination of bursting strength
    ISO 187:1990 Paper, board and pulps — Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples
    ISO 5636-1:1984 Paper and board Determination of air permeance (medium range) Part 1: General method
    ISO 801-1:1994 Pulps Determination of saleable mass in lots Part 1: Pulp baled in sheet form
    ISO 9197:2016 Paper, board and pulps Determination of water-soluble chlorides
    ISO 217:2013 Paper Untrimmed sizes Designation and tolerances for primary and supplementary ranges, and indication of machine direction
    ISO 9184-1:1990 Paper, board and pulps — Fibre furnish analysis — Part 1: General method
    ISO 5628:2012 Paper and board — Determination of bending stiffness — General principles for two-point, three-point and four-point methods
    ISO 15359:1999 Paper and board Determination of the static and kinetic coefficients of friction Horizontal plane method
    ISO 8787:1986 Paper and board — Determination of capillary rise — Klemm method
    ISO 216:2007 Writing paper and certain classes of printed matter Trimmed sizes A and B series, and indication of machine direction
    ISO 10716:1994 Paper and board Determination of alkali reserve
    ISO 2144:2015 Paper, board and pulps Determination of residue (ash) on ignition at 900 degrees C
    ISO 2528:2017 Sheet materials — Determination of water vapour transmission rate (WVTR) — Gravimetric (dish) method
    ISO 186:2002 Paper and board — Sampling to determine average quality
    ISO 1924-2:2008 Paper and board — Determination of tensile properties — Part 2: Constant rate of elongation method (20 mm/min)
    ISO 5635:1978 Paper Measurement of dimensional change after immersion in water
    ISO 8791-1:1986 Paper and board — Determination of roughness/smoothness (air leak methods) — Part 1: General method
    ISO 3781:2011 Paper and board — Determination of tensile strength after immersion in water
    ISO 536:2012 Paper and board Determination of grammage
    ISO 2493:1992 Paper and board Determination of resistance to bending
    ISO 287:2017 Paper and board — Determination of moisture content of a lot — Oven-drying method
    ISO 14968:1999 Paper and board Cut-size office paper Measurement of curl in a pack of sheets
    ISO 12192:2011 Paper and board — Determination of compressive strength — Ring crush method
    ISO 2469:2014 Paper, board and pulps — Measurement of diffuse radiance factor (diffuse reflectance factor)
    ISO 3035:2011 Corrugated fibreboard — Determination of flat crush resistance
    ISO 534:2011 Paper and board — Determination of thickness, density and specific volume
    ISO 3037:2013 Corrugated fibreboard — Determination of edgewise crush resistance (unwaxed edge method)
    ISO 5267-2:2001 Pulps — Determination of drainability — Part 2: "Canadian Standard" freeness method
    ISO 5633:1983 Paper and board Determination of resistance to water penetration
    ISO 11480:2017 Pulp, paper and board — Determination of total chlorine and organically bound chlorine
    ISO 535:2014 Paper and board — Determination of water absorptiveness — Cobb method
    ISO 3260:2015 Pulps Determination of chlorine consumption (Degree of delignification)
    ISO 2470:1999 Paper, board and pulps Measurement of diffuse blue reflectance factor (ISO brightness)
    ISO 2759:2014 Board — Determination of bursting strength
    ISO 7213:1981 Pulps Sampling for testing
    ISO 9198:2001 Paper, board and pulp Determination of water-soluble sulfates
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective