Skip to content
Please enter a keyword to search

  • BS ISO 8178-1:2017

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Reciprocating internal combustion engines. Exhaust emission measurement Test-bed measurement systems of gaseous and particulate emissions

    Available format(s):  Hardcopy, PDF

    Superseded date:  26-06-2020

    Language(s):  English

    Published date:  29-06-2017

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 General measurement principles
    6 Engine and ambient related measurement equipment
    7 Determination of the gaseous components
    8 Particulate determination
    9 Calibration and verification
    Annex A (normative) - Heat calculation (transfer tube)
    Annex B (normative) - Determination of system
            equivalence
    Annex C (informative) - Carbon flow check
    Annex D (informative) - Statistical equations
    Annex E (informative) - Examples of Partial Flow
            Dilution Systems
    Annex F (informative) - Examples of exhaust gas
            analysis system
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the measurement methods for gaseous and particulate exhaust emissions from reciprocating internal combustion (RIC) engines on a test bed, necessary for determining one weighted value for each exhaust gas pollutant.

    General Product Information - (Show below) - (Hide below)

    Committee MCE/14/-/3
    Development Note Supersedes BS EN ISO 8178-1 & 02/706744 DC. (09/2009) Supersedes 16/30334062 DC. (07/2017)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 5167-3:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 3: Nozzles and Venturi nozzles
    ISO 5725-1:1994 Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions
    SAE J 244 : 2011 MEASUREMENT OF INTAKE AIR OR EXHAUST GAS FLOW OF DIESEL ENGINES
    ISO 8178-5:2015 Reciprocating internal combustion engines Exhaust emission measurement Part 5: Test fuels
    CFR 40(PTS87-95) : JUL 2017 PROTECTION OF ENVIRONMENT
    ISO 7066-2:1988 Assessment of uncertainty in the calibration and use of flow measurement devices — Part 2: Non-linear calibration relationships
    ISO 5168:2005 Measurement of fluid flow — Procedures for the evaluation of uncertainties
    ISO 2710-1:2000 Reciprocating internal combustion engines Vocabulary Part 1: Terms for engine design and operation
    ISO 2710-2:1999 Reciprocating internal combustion engines Vocabulary Part 2: Terms for engine maintenance
    ISO 8178-2:2008 Reciprocating internal combustion engines Exhaust emission measurement Part 2: Measurement of gaseous and particulate exhaust emissions under field conditions
    ISO 8178-3:1994 Reciprocating internal combustion engines Exhaust emission measurement Part 3: Definitions and methods of measurement of exhaust gas smoke under steady-state conditions
    ISO 5167-4:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 4: Venturi tubes
    ISO 16183:2002 Heavy duty engines — Measurement of gaseous emissions from raw exhaust gas and of particulate emissions using partial flow dilution systems under transient test conditions
    ISO 5167-2:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 2: Orifice plates
    ISO 14396:2002 Reciprocating internal combustion engines Determination and method for the measurement of engine power Additional requirements for exhaust emission tests in accordance with ISO 8178
    SAE J 1151 : 2011 METHANE MEASUREMENT USING GAS CHROMATOGRAPHY
    ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements
    IMO IB664 : 2013 SUPP 2015 MARPOL ANNEX VI & NTC 2008
    ISO 5725-2:1994 Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method
    ISO 3046-1:2002 Reciprocating internal combustion engines Performance Part 1: Declarations of power, fuel and lubricating oil consumptions, and test methods Additional requirements for engines for general use
    ISO 8178-7:2015 Reciprocating internal combustion engines Exhaust emission measurement Part 7: Engine family determination
    ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
    ISO 8178-4:2017 Reciprocating internal combustion engines Exhaust emission measurement Part 4: Steady-state and transient test cycles for different engine applications
    CFR 40(PTS1000-END) : JUL 2016 PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY AND DEPARTMENT OF JUSTICE COUNCIL ON ENVIRONMENTAL QUALITY
    ISO 2534:1998 Road vehicles Engine test code Gross power
    ISO 9249:2007 Earth-moving machinery — Engine test code — Net power
    ISO 8665:2006 Small craft Marine propulsion reciprocating internal combustion engines Power measurements and declarations
    ISO 1585:1992 Road vehicles Engine test code Net power
    ISO 3046-3:2006 Reciprocating internal combustion engines Performance Part 3: Test measurements
    ISO 8178-6:2000 Reciprocating internal combustion engines Exhaust emission measurement Part 6: Report of measuring results and test
    ISO 15550:2016 Internal combustion engines Determination and method for the measurement of engine power General requirements
    ISO 8178-8:2015 Reciprocating internal combustion engines Exhaust emission measurement Part 8: Engine group determination
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective