EN 29002 : 1994
|
QUALITY SYSTEMS - MODEL FOR QUALITY ASSURANCE IN PRODUCTION & INSTALLATION |
DIN ISO 228-2:1988-07
|
PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - VERIFICATION BY MEANS OF LIMIT GAUGES |
ISO 2859:1974
|
Sampling procedures and tables for inspection by attributes |
DIN ISO 2859-1:2014-08
|
SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION (ISO 2859-1:1999 + COR. 1:2001 + AMD.1:2011) |
EN 1562:2012
|
Founding - Malleable cast irons |
DIN ISO 228-1:1994-12
|
PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION |
PREN 1562 : DRAFT 2009
|
FOUNDING - MALLEABLE CAST IRONS |
EN ISO 9002:1994/AC:1997
|
QUALITY SYSTEMS - SPECIFICATION FOR PRODUCTION AND INSTALLATION |
ISO 7-2:2000
|
Pipe threads where pressure-tight joints are made on the threads Part 2: Verification by means of limit gauges |
ISO 6708:1995
|
Pipework components Definition and selection of DN (nominal size) |
DIN 50049:1992-04
|
METALLIC PRODUCTS; TYPES OF INSPECTION DOCUMENTS |
ISO 2859-2:1985
|
Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
ISO 2859-0:1995
|
Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system |
DIN 2999-1:1983-07
|
PIPE THREADS FOR TUBES AND FITTINGS - PARALLEL INTERNAL THREAD AND TAPER EXTERNAL THREAD - TREAD DIMENSIONS |
DIN 50988-1:1984-02
|
MEASUREMENT OF COATING THICKNESS; DETERMINATION OF THE MASS PER UNIT AREA OF ZINC- AND TIN-COATINGS ON FERROUS MATERIALS BY DISSOLUTION OF THE COATING MATERIAL; GRAVIMETRIC METHOD |
ISO 9002:1994
|
Quality systems — Model for quality assurance in production, installation and servicing |
EN ISO 6708:1995
|
Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
EN ISO 228-1:2003
|
Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
ISO 7-1:1994
|
Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
EN ISO 9001:2015
|
Quality management systems - Requirements (ISO 9001:2015) |
DIN EN 26708 : 1993
|
|
EN 10204:2004
|
Metallic products - Types of inspection documents |
ISO 9001:2015
|
Quality management systems — Requirements |
ISO 2178:2016
|
Non-magnetic coatings on magnetic substrates Measurement of coating thickness Magnetic method |
DIN EN ISO 9001:2015-11
|
QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS (ISO 9001:2015) |
ISO 1460:1992
|
Metallic coatings Hot dip galvanized coatings on ferrous materials Gravimetric determination of the mass per unit area |
EN 45012 : 1998
|
GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
EN 29001 : 1994
|
QUALITY SYSTEMS - MODEL FOR QUALITY ASSURANCE IN DESIGN/DEVELOPMENT, PRODUCTION, INSTALLATION & SERVICING |
ISO 228-1:2000
|
Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |