Skip to content
Please enter a keyword to search

  • DIN EN 14399-9:2016-01 (Draft)

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES

    Available format(s):  Hardcopy, PDF

    Superseded date:  07-03-2021

    Language(s):  German

    Published date:  01-01-2016

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Vorwort
    Einleitung
    1 Anwendungsbereich
    2 Normative Verweisungen
    3 Direkte Kraftanzeiger
      3.1 Masse
      3.2 Technische Lieferbedingungen und Bezugsnormen
      3.3 Leistungsprüfung der direkten Kraftanzeiger
      3.4 Prüfverfahren für die Messung der Druckbelastung
          (alle Oberflächenausführungen) von direkten
          Kraftanzeigern
          3.4.1 Allgemeines
          3.4.2 Prüfeinrichtung
          3.4.3 Druckbelastungssystem
          3.4.4 Auflageblöcke
          3.4.5 Lagerblöcke
          3.4.6 Kalibrierung
          3.4.7 Durchführung der Prüfung
      3.5 Kennzeichnung des direkten Kraftanzeigers
      3.6 Bezeichnung des direkten Kraftanzeigers
    4 Mutterseitige und schraubenkopfseitige Scheiben
      4.1 Masse
      4.2 Technische Lieferbedingungen und Bezugsnormen
          für mutterseitige und schraubenkopfseitige Scheiben
      4.3 Kennzeichnung
          4.3.1 Mutterseitige Scheiben
          4.3.2 Schraubenkopfseitige Scheiben
      4.4 Bezeichnung
          4.4.1 Mutterseitige Scheiben
          4.4.2 Schraubenkopfseitige Scheiben
    5 Gebrauchseigenschaften
      5.1 Garnituren
      5.2 Gebrauchseigenschaften der direkten Kraftanzeiger
          in der Garnitur
      5.3 Gebrauchseigenschaften der Garnitur aus
          Schraube, Mutter, Scheibe(n) und direktem
          Kraftanzeiger
          5.3.1 Allgemeines
          5.3.2 Durchführung der Prüfung
    Anhang A (informativ) Besondere Prüfbedingungen
             und -abläufe
    Literaturhinweise
    Bilder
    Tabellen

    Abstract - (Show below) - (Hide below)

    Defines, together with EN 14399-1, the requirements for assemblies of high-strength structural bolts and nuts, with large width across flats, of system HR or HV, including the requirements for the general dimensions, tolerances, materials and performance for two grades, H[8] and H[10], of compressible washer-type direct tension indicators, nut face washers and bolt face washers suitable for preloaded joints.

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Development Note Applies in conjunction with DIN EN 14399-1 issue 06-2006. (07/2009) DRAFT 2016 issued in January 2016. (01/2016)
    Document Type Draft
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 6507-1:2005 Metallic materials Vickers hardness test Part 1: Test method
    EN 14399-8:2007 High-strength structural bolting assemblies for preloading - Part 8: System HV - Hexagon fit bolt and nut assemblies
    EN ISO 6508-1:2016 Metallic materials - Rockwell hardness test - Part 1: Test method (ISO 6508-1:2016)
    EN 14399-3:2015 High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies
    ISO 4759-3:2016 Tolerances for fasteners Part 3: Washers for bolts, screws and nuts Product grades A, C and F
    DIN ISO 2859-1:2014-08 SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION (ISO 2859-1:1999 + COR. 1:2001 + AMD.1:2011)
    ISO 6508-1:2016 Metallic materials — Rockwell hardness test — Part 1: Test method
    EN ISO 4759-3:2016 Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F (ISO 4759-3:2016)
    EN 13811 : 2003 SHERARDIZING - ZINC DIFFUSION COATINGS ON FERROUS PRODUCTS - SPECIFICATION
    EN ISO 3269:2000 FASTENERS - ACCEPTANCE INSPECTION
    EN 14399-6:2015 High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers
    EN 14399-1:2015 High-strength structural bolting assemblies for preloading - Part 1: General requirements
    EN 10204:2004 Metallic products - Types of inspection documents
    EN 14399-4:2015 High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies
    EN 1090-2:2008+A1:2011 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
    ISO 7500-1:2015 Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system
    EN 14399-7:2007 High-strength structural bolting assemblies for preloading - Part 7: System HR - Countersunk head bolt and nut assemblies
    EN 14399-5:2015 High-strength structural bolting assemblies for preloading - Part 5: Plain washers
    EN 1993-1-8:2005/AC:2009 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-8: DESIGN OF JOINTS
    ISO 3269:2000 Fasteners Acceptance inspection
    EN 1993-1-1:2005/A1:2014 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
    EN 14399-2:2015 High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloading
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective