Skip to content
Please enter a keyword to search

  • EN 62196-2:2017

    Current The latest, up-to-date edition.

    Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories

    Available format(s): 

    Language(s): 

    Published date:  28-04-2017

    Publisher:  European Committee for Standards - Electrical

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General
    5 Ratings
    6 Connection between the power supply and the
       electric vehicle
    7 Classification of accessories
    8 Marking
    9 Dimensions
    10 Protection against electric shock
    11 Size and colour of protective earthing conductors
    12 Provision for earthing
    13 Terminals
    14 Interlocks
    15 Resistance to ageing of rubber and thermoplastic
       material
    16 General construction
    17 Construction of socket-outlets
    18 Construction of plugs and vehicle connectors
    19 Construction of vehicle inlets
    20 Degrees of protection
    21 Insulation resistance and dielectric strength
    22 Breaking capacity
    23 Normal operation
    24 Temperature rise
    25 Flexible cables and their connection
    26 Mechanical strength
    27 Screws, current-carrying parts and connections
    28 Creepage distances, clearances and distances
    29 Resistance to heat, to fire and to tracking
    30 Corrosion and resistance to rusting
    31 Conditional short-circuit current withstand test
    32 Electromagnetic compatibility (EMC)
    33 Vehicle driveover
    201 Components
    202 Resistor coding
    STANDARD SHEETS
    CONFIGURATION TYPE 1
    CONFIGURATION TYPE 2
    CONFIGURATION TYPE 3
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    IEC 62196-2:2016 applies to plugs, socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. They have a nominal rated operating voltage not exceeding 480 V a.c., 50 Hz to 60 Hz, and a rated current not exceeding 63 A three-phase or 70 A single phase, for use in conductive charging of electric vehicles. This second edition cancels and replaces the first edition published in 2011 and constitutes a technical revision. This second edition includes the following significant technical changes with respect to the previous edition.

    a) Standard sheets for configurations type 2 and type 3 have been updated.

    b) Configuration type 2 is now available with optional shutter.


    This publication is to be read in conjunction with IEC 62196-1:2014.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher European Committee for Standards - Electrical
    Status Current

    Standards Referenced By This Book - (Show below) - (Hide below)

    EN 62196-3:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers
    UNE-HD 60364-7-722:2016 Low-voltage electrical installations - Part 7-722: Requirements for special installations or locations - Supplies for electric vehicles
    I.S. EN 62752:2016&AC:2019-03 IN-CABLE CONTROL AND PROTECTION DEVICE FOR MODE 2 CHARGING OF ELECTRIC ROAD VEHICLES (IC-CPD)
    HD 60364-7-722:2016 Low-voltage electrical installations - Part 7-722: Requirements for special installations or locations - Supplies for electric vehicles
    I.S. EN 62196-3:2014 PLUGS, SOCKET-OUTLETS, VEHICLE CONNECTORS AND VEHICLE INLETS - CONDUCTIVE CHARGING OF ELECTRIC VEHICLES - PART 3: DIMENSIONAL COMPATIBILITY AND INTERCHANGEABILITY REQUIREMENTS FOR D.C. AND A.C./D.C. PIN AND CONTACT-TUBE VEHICLE COUPLERS
    S.R. HD 60364-7-722:2016 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-722: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - SUPPLIES FOR ELECTRIC VEHICLES
    EN 62752:2016 In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD)
    CEI EN 62752 : 1ED 2017 IN-CABLE CONTROL AND PROTECTION DEVICE FOR MODE 2 CHARGING OF ELECTRIC ROAD VEHICLES (IC-CPD)
    UNE-EN 62196-3:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers
    BS EN 62196-3:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers
    UNE-EN 62752:2017 In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD)

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 62196-1:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements
    IEC 62196-1:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective