Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN 13053:2006

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    VENTILATION FOR BUILDINGS - AIR HANDLING UNITS - RATING AND PERFORMANCE FOR UNITS, COMPONENTS AND SECTIONS

    Available format(s):  Hardcopy, PDF

    Superseded date:  09-01-2020

    Language(s):  English

    Published date:  01-01-2006

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviations
    5 Ratings and performance of the entire air handling unit
    6 Ratings and performance of the entire air handling unit
    7 Extended hygiene requirements for special applications
    8 Instructions for installation, operation and maintenance
    Annex A (informative) - Air handling units - Heat recovery
            - Defrosting - Requirements and testing
    Annex B (informative) - Air handling units - Heat recovery
            - Characteristics
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes requirements and testing for ratings and performance of air handling units as a whole. Also specifies requirements, recommendations, classification, and testing of specific components and sections of air handling units.

    General Product Information - (Show below) - (Hide below)

    Development Note 2006 Edition Re-Issued in July 2011 & incorporates AMD 1 2011. (07/2011)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 1886:2007 Ventilation for buildings - Air handling units - Mechanical performance
    ISO 13348:2007 Industrial fans — Tolerances, methods of conversion and technical data presentation
    EN ISO 5136:2009 Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct method (ISO 5136:2003)
    ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
    EN 305:1997 Heat exchangers - Definitions of performance of heat exchangers and the general test procedure for establishing performance of all heat exchangers
    ISO 5168:2005 Measurement of fluid flow — Procedures for the evaluation of uncertainties
    ISO 9614-1:1993 Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points
    EN 12792:2003 Ventilation for buildings - Symbols, terminology and graphical symbols
    EN ISO 3741:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Precision methods for reverberation test rooms (ISO 3741:2010)
    ISO 9614-2:1996 Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning
    EN 10088-2:2014 STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES
    EN 779:2012 Particulate air filters for general ventilation - Determination of the filtration performance
    EN ISO 7235:2009 Acoustics - Laboratory measurement procedures for ducted silencers and air-terminal units - Insertion loss, flow noise and total pressure loss (ISO 7235:2003)
    ISO 5801:2017 Fans — Performance testing using standardized airways
    EN ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003)
    ISO 3746:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane
    EN ISO 3746:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)
    EN 308:1997 Heat exchangers - Test procedures for establishing performance of air to air and flue gases heat recovery devices
    EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
    ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements
    ISO 9614-3:2002 Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 3: Precision method for measurement by scanning
    EN ISO 9614-2 : 1996 ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND INTENSITY - PART 2: MEASUREMENT BY SCANNING
    IEC 60034-2:1972 Rotating electrical machines. Part 2: Methods for determining losses and efficiency of rotating electrical machinery from tests (excluding machines for traction vehicles)
    EN 1751:2014 Ventilation for buildings - Air terminal devices - Aerodynamic testing of damper and valves
    EN ISO 9614-3:2009 Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 3: Precision method for measurement by scanning (ISO 9614-3:2002)
    ISO 3741:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Precision methods for reverberation test rooms
    EN 60034-2:1996/A2:1996 ROTATING ELECTRICAL MACHINES - PART 2: METHODS FOR DETERMINING LOSSES AND EFFICIENCY OF ROTATING ELECTRICAL MACHINERY FROM TESTS (EXCLUDING MACHINES FOR TRACTION VEHICLES)
    ISO 7235:2003 Acoustics — Laboratory measurement procedures for ducted silencers and air-terminal units — Insertion loss, flow noise and total pressure loss
    EN 1216:1998/A1:2002 HEAT EXCHANGERS - FORCED CIRCULATION AIR-COOLING AND AIR-HEATING COILS - TEST PROCEDURES FOR ESTABLISHING THE PERFORMANCE
    ISO 5221:1984 Air distribution and air diffusion Rules to methods of measuring air flow rate in an air handling duct
    EN 13779:2007 Ventilation for non-residential buildings - Performance requirements for ventilation and room-conditioning systems
    ISO 3966:2008 Measurement of fluid flow in closed conduits Velocity area method using Pitot static tubes
    ISO 5136:2003 Acoustics — Determination of sound power radiated into a duct by fans and other air-moving devices — In-duct method
    EN ISO 9614-1:2009 Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993)
    EN 13030:2001 Ventilation for buildings - Terminals - Performance testing of louvres subjected to simulated rain
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective