I.S. EN 50065-4-7:2005

SIGNALLING ON LOW-VOLTAGE ELECTRICAL INSTALLATIONS IN THE FREQUENCY RANGE 3 KHZ TO 148,5 KHZ AND 1,6 MHZ TO 30 MHZ - PART 4-7: PORTABLE LOW VOLTAGE DECOUPLING FILTERS - SAFETY REQUIREMENTS

National Standards Authority of Ireland

Preview

Current

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Add To Cart

Product Format

Table of Contents - (Show below) - (Hide below)

1 Scope
2 Normative references
3 Definitions
4 General requirements
5 General notes on tests
6 Rating
7 Classification
8 Marking
9 Dimensions
10 Protection against electric shock
11 Provision for protective earthing
12 Terminals
13 Construction
14 Resistance to ageing, protection provided by enclosures,
and resistance to humidity
15 Insulation resistance and dielectric strength
16 Temperature rise
17 Breaking capacity
18 Normal operation
19 Force necessary to withdraw the plug
20 Flexible cables and their connections
21 Mechanical strength
22 Resistance to heat
23 Screws, current-carrying parts and connections
24 Creepage distances and clearances
25 Resistance to abnormal heat, to fire and to tracking
26 Resistance to rusting
27 Components
28 Abnormal conditions
29 Protection against short-circuit
30 Resistance to transients
Annex A (normative) Pollution degrees
Annex B (normative) Proof tracking test
Annex C (normative) Types of coatings for rigid printed
board assemblies
Annex D (normative) Special national conditions
Tables
Figures

Abstract - (Show below) - (Hide below)

Applicable to the filter part of portable devices for household and similar uses (hereafter referred to as portable decoupling filters) consisting of the filter part, a plug or an appliance inlet or a provision for connection by terminals or with a non-rewirable cord and one (multiple) socket-outlet or an appliance outlet.

General Product Information - (Show below) - (Hide below)

Published
Document Type	Standard
Status	Current
Publisher	National Standards Authority of Ireland
Pages
ISBN

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
BS EN 50065-4-7 : 2005	Identical
EN 50065-4-7 : 2005 COR 2006	Identical
NEN EN 50065-4-7 : 2005 C1 2006	Identical
NBN EN 50065-4-7 : 2006	Identical
SN EN 50065-4-7 : 2005	Identical
DIN EN 50065-4-7 : 2006 COR 1 2007	Identical
UNE EN 50065-4-7 : 2006	Identical
BS EN 50065-4-7 : 2005	Identical

Standards Referencing This Book - (Show below) - (Hide below)

IEC 60112 : 4.1	METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS
IEC 60065 : 1970	AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
EN 60068-2-75 : 2014	ENVIRONMENTAL TESTING - PART 2-75: TESTS - TEST EH: HAMMER TESTS (IEC 60068-2-75:2014)
EN 60065 : 2014 COR 2017	AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016)
EN 60695-10-2 : 2014	FIRE HAZARD TESTING - PART 10-2: ABNORMAL HEAT - BALL PRESSURE TEST METHOD (IEC 60695-10-2:2014)
IEC 60884-1:2002+AMD1:2006+AMD2:2013 CSV	PLUGS AND SOCKET-OUTLETS FOR HOUSEHOLD AND SIMILAR PURPOSES - PART 1: GENERAL REQUIREMENTS
IEC 60893-1 : 2.0	INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 1: DEFINITIONS, DESIGNATIONS AND GENERAL REQUIREMENTS
EN 60112 : 2003 AMD 1 2009	METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS
IEC 60999-1 : 2.0	CONNECTING DEVICES - ELECTRICAL COPPER CONDUCTORS - SAFETY REQUIREMENTS FOR SCREW-TYPE AND SCREWLESS-TYPE CLAMPING UNITS - PART 1: GENERAL REQUIREMENTS AND PARTICULAR REQUIREMENTS FOR CLAMPING UNITS FOR CONDUCTORS FROM 0,2 MM[2] UP TO 35 MM[2] (INCLUDED)
IEC 60085 : 4.0	ELECTRICAL INSULATION - THERMAL EVALUATION AND DESIGNATION
EN 132400 : 1994 AMD 4 2001	SECTIONAL SPECIFICATION: FIXED CAPACITORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION AND CONNECTION TO THE SUPPLY MAINS (ASSESSMENT LEVEL D)
IEC 61180-2 : 1.0	HIGH-VOLTAGE TEST TECHNIQUES FOR LOW-VOLTAGE EQUIPMENT - PART 2: TEST EQUIPMENT
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV	DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE)
EN 60695-2-10 : 2013	FIRE HAZARD TESTING - PART 2-10: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE APPARATUS AND COMMON TEST PROCEDURE (IEC 60695-2-10:2013)
IEC 60884-2-5 : 2.0	PLUGS AND SOCKET-OUTLETS FOR HOUSEHOLD AND SIMILAR PURPOSES - PART 2-5: PARTICULAR REQUIREMENTS FOR ADAPTORS
EN 61032 : 1998	PROTECTION OF PERSONS AND EQUIPMENT BY ENCLOSURES - PROBES FOR VERIFICATION (IEC 61032:1997)
EN 60664-1 : 2007	INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS
IEC 60721-3-3 : 2.2	CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - PART 3-3: CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STATIONARY USE AT WEATHERPROTECTED LOCATIONS
IEC 60068-2-75 : 2014	ENVIRONMENTAL TESTING - PART 2-75: TESTS - TEST EH: HAMMER TESTS
IEC 60664-3 : 3.0	INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 3: USE OF COATING, POTTING OR MOULDING FOR PROTECTION AGAINST POLLUTION
EN 60999-1 : 2000	CONNECTING DEVICES - ELECTRICAL COPPER CONDUCTORS - SAFETY REQUIREMENTS FOR SCREW-TYPE AND SCREWLESS-TYPE CLAMPING UNITS - PART 1: GENERAL REQUIREMENTS AND PARTICULAR REQUIREMENTS FOR CLAMPING UNITS FOR CONDUCTORS FROM 0,2 MM[2] UP TO 35 MM[2] (INCLUDED)
EN 61140 : 2016	PROTECTION AGAINST ELECTRIC SHOCK - COMMON ASPECTS FOR INSTALLATION AND EQUIPMENT (IEC 61140:2016)
IEC 60695-10-2 : 3.0 : 2014	FIRE HAZARD TESTING - PART 10-2: ABNORMAL HEAT - BALL PRESSURE TEST METHOD
IEC 61180-1 : 1.0	HIGH-VOLTAGE TEST TECHNIQUES FOR LOW VOLTAGE EQUIPMENT - DEFINITIONS, TEST AND PROCEDURE REQUIREMENTS
EN 60529 : 1991 COR 2016	DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
IEC 61140 : 4.0	PROTECTION AGAINST ELECTRIC SHOCK - COMMON ASPECTS FOR INSTALLATIONS AND EQUIPMENT
EN 60068-2-32 : 1993	BASIC ENVIRONMENTAL TESTING PROCEDURES - PART 2: TESTS - TEST ED: FREE FALL
IEC 61032 : 2.0 : 1997	BASIC SAFETY PUBLICATION - PROTECTION OF PERSONS AND EQUIPMENT BY ENCLOSURES - PROBES FOR VERIFICATION
IEC 60695-2-10 : 2.0 : 2013	FIRE HAZARD TESTING - PART 2-10: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE APPARATUS AND COMMON TEST PROCEDURE
EN 61180-2 : 1994	HIGH-VOLTAGE TEST TECHNIQUES FOR LOW-VOLTAGE EQUIPMENT - PART 2: TEST EQUIPMENT
IEC 60664-1 : 2.0	INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS
EN 60664-3 : 2017	INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 3: USE OF COATING, POTTING OR MOULDING FOR PROTECTION AGAINST POLLUTION (IEC 60664-3:2016)
EN 61180-1 : 1994	HIGH-VOLTAGE TEST TECHNIQUES FOR LOW-VOLTAGE EQUIPMENT - PART 1: DEFINITIONS, TEST AND PROCEDURE REQUIREMENTS
EN 60893-1 : 2004	INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 1: DEFINITIONS, DESIGNATIONS AND GENERAL REQUIREMENTS
EN 60721-3-3 : 95 AMD 2 97	CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STATIONARY USE AT WEATHER-PROTECTED LOCATIONS