Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN 60695-2-13:2010

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS

    Available format(s):  Hardcopy, PDF

    Superseded date:  23-10-2021

    Language(s):  English

    Published date:  01-01-2010

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Test specimens
    5 Apparatus
    6 Temperature measuring system verification
    7 Conditioning and test conditions
    8 Test procedure
    9 Observations and measurements
    10 Evaluation of test results
    11 Test report
    Bibliography
    Annex ZA (normative) - Normative references to international
             publications with their corresponding European
             publications

    Abstract - (Show below) - (Hide below)

    Describes the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for ignitability testing to determine the glow-wire ignition temperature (GWIT).

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
    IEC 60695-1-30:2017 Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines
    ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
    ISO 13943:2017 Fire safety — Vocabulary
    IEC 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
    EN ISO 293:2005 Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2004)
    ISO/IEC Guide 51:2014 Safety aspects Guidelines for their inclusion in standards
    IEC 60695-2-12:2010+AMD1:2014 CSV Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods- Glow-wire flammability index (GWFI) test method for materials
    EN 60695-2-10:2013 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
    IEC GUIDE 104:2010 The preparation of safety publications and the use of basic safety publications and group safety publications
    EN 60695-1-30:2017 Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines
    EN ISO 295 : 2004 PLASTICS - COMPRESSION MOULDING OF TEST SPECIMENS OF THERMOSETTING MATERIALS
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    EN ISO 291:2008 Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008)
    IEC 60695-1-11:2014 Fire hazard testing - Part 1-11: Guidance for assessing the fire hazard of electrotechnical products - Fire hazard assessment
    IEC 60695-2-10:2013 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
    EN 60695-2-12:2010/A1:2014 FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS (IEC 60695-2-12:2010/A1:2014)
    IEC 60695-1-10:2016 Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective