Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN ISO 10135:2009

    Current The latest, up-to-date edition.

    GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DRAWING INDICATIONS FOR MOULDED PARTS IN TECHNICAL PRODUCT DOCUMENTATION (TPD)

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2009

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Letter Symbols
    5 Line conventions
    6 Drawing indications for moulded parts
      6.1 Parting surface
      6.2 Tool markings
      6.3 Special ejector markings identifier
      6.4 Mismatch
      6.5 Flash
      6.6 Extent of specification
      6.7 Draft angles
      6.8 Tool motion direction
      6.9 Part removal direction
      6.10 Surface enlargement
      6.11 Sinks
      6.12 Porosity
      6.13 Identification and marking
      6.14 Other necessary information
      6.15 Special indication for undisturbed surfaces
    7 Rules for linear and geometrical dimensioning and
      tolerancing
      7.1 Linear dimensioning and tolerancing
      7.2 Geometrical tolerancing
      7.3 Datums
      7.4 Surface texture
      7.5 Edges
    Annex A (normative) - Proportions and dimensions of
            graphical symbols
    Annex B (informative) - Former practice (tapered features)
    Annex C (informative) - Relation to the GPS matrix model
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes rules and conventions for the indications of requirements for moulded parts on technical product documentation. It also specifies the proportions and dimensions of the graphical symbols used for this representation.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/TR 14638:1995 Geometrical product specification (GPS) Masterplan
    ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
    ISO 5459:2011 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
    ISO 2692:2014 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
    ISO 128-24:2014 Technical drawings General principles of presentation Part 24: Lines on mechanical engineering drawings
    ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
    ISO 7083:1983 TECHNICAL DRAWINGS - SYMBOLS FOR GEOMETRICAL TOLERANCING - PROPORTIONS AND DIMENSIONS
    ISO 11971:2008 Steel and iron castings Visual examination of surface quality
    ISO 15787:2016 Technical product documentation Heat-treated ferrous parts Presentation and indications
    ISO 81714-1:2010 Design of graphical symbols for use in the technical documentation of products Part 1: Basic rules
    ISO 406:1987 Technical drawings Tolerancing of linear and angular dimensions
    ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
    ISO 8062-1:2007 Geometrical product specifications (GPS) Dimensional and geometrical tolerances for moulded parts Part 1: Vocabulary
    ISO 128-22:1999 Technical drawings General principles of presentation Part 22: Basic conventions and applications for leader lines and reference lines
    ISO 14660-2:1999 Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature
    ISO 8785:1998 Geometrical Product Specification (GPS) — Surface imperfections — Terms, definitions and parameters
    ISO 128-20:1996 Technical drawings General principles of presentation Part 20: Basic conventions for lines
    ISO 129-1:2004 Technical drawings Indication of dimensions and tolerances Part 1: General principles
    ISO 14660-1:1999 Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions
    ISO 13715:2017 Technical product documentation Edges of undefined shape Indication and dimensioning
    ISO 8062:1994 Castings System of dimensional tolerances and machining allowances
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective