Skip to content
Please enter a keyword to search

  • IEC PAS 61076-3-126:2018

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Connectors for electrical and electronic equipment - Product requirements - Part 3-126: Rectangular connectors - Detail specification for 5 pole power connector for industrial environments with push-pull locking

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  31-01-2023

    Language(s):  English

    Published date:  09-01-2018

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Technical information
    5 Dimensional information
    6 Characteristics
    7 Test schedule

    Abstract - (Show below) - (Hide below)

    IEC/PAS 61076-3-126:2018(E) covers rectangular IP65/IP67 connectors with 5 poles for electric power supply up to 16 A. These connectors consist of fixed and free connectors, either rewirable or non- rewirable (for both portions). It uses the general function principles of the push-pull connector housing system described in IEC 61076-3-117 with IP65/IP67 degree of protection according to IEC 60529 for harsh applications.
    Male connectors have 5 square 1 mm electric contacts, with 16 A rated current. Connectors according this document are without breaking capacity COC according to IEC 61984, therefore they are not intended to be engaged or disengaged in normal use when live or under load, if not otherwise specified by the manufacturer.

    General Product Information - (Show below) - (Hide below)

    Committee TC 48/SC 48B
    Development Note Stability Date: 2020. (01/2018)
    Document Type Miscellaneous Product
    Publisher International Electrotechnical Committee
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC GUIDE 109:2012 Environmental aspects - Inclusion in electrotechnical product standards
    IEC 61076-1:2006 Connectors for electronic equipment - Product requirements - Part 1: Generic specification
    IEC 60352-3:1993 Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance
    IEC 60512-11-4:2002 Connectors for electronic equipment - Tests and measurements - Part 11-4: Climatic tests - Test 11d: Rapid change of temperature
    IEC 60512-11-9:2002 Connectors for electronic equipment - Tests and measurements - Part 11-9: Climatic tests - Test 11i: Dry heat
    IEC 60512-11-10:2002 Connectors for electronic equipment - Tests and measurements - Part 11-10: Climatic tests - Test 11j: Cold
    IEC 61984:2008 Connectors - Safety requirements and tests
    IEC 60352-6:1997 Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance
    IEC 60512-3-1:2002 Connectors for electronic equipment - Tests and measurements - Part 3-1: Insulation tests - Test 3a: Insulation resistance
    IEC 61076-3:2008 Connectors for electronic equipment - Product requirements - Part 3: Rectangular connectors - Sectional specification
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    IEC 60512-9-2:2011 Connectors for electronic equipment - Tests and measurements - Part 9-2: Endurance tests - Test 9b: Electrical load and temperature
    IEC 60512-13-5:2006 Connectors for electronic equipment - Tests and measurements - Part 13-5: Mechanical operation tests - Test 13e: Polarizing and keying method
    IEC 60512-8-1:2010 Connectors for electronic equipment - Tests and measurements - Part 8-1: Static load tests (fixed connectors) - Test 8a: Static load, transverse
    IEC 60512-6-3:2002 Connectors for electronic equipment - Tests and measurements - Part 6-3: Dynamic stress tests - Test 6c: Shock
    IEC 60512-15-1:2008 Connectors for electronic equipment - Tests and measurements - Part 15-1: Connector tests (mechanical) - Test 15a: Contact retention in insert
    IEC 60512-8-2:2011 Connectors for electronic equipment - Tests and measurements - Part 8-2: Static load tests (fixed connectors) - Test 8b: Static load, axial
    ISO 11469:2016 Plastics — Generic identification and marking of plastics products
    IEC 60999-2:2003 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included)
    IEC 60512-6-1:2002 Connectors for electronic equipment - Tests and measurements - Part 6-1: Dynamic stress tests - Test 6a: Acceleration, steady state
    IEC 60512-13-2:2006 Connectors for electronic equipment - Tests and measurements - Part 13-2: Mechanical operation tests - Test 13b: Insertion and withdrawal forces
    IEC 62430:2009 Environmentally conscious design for electrical and electronic products
    IEC 60512-2-5:2003 Connectors for electronic equipment - Tests and measurements - Part 2-5: Electrical continuity and contact resistance tests - Test 2e: Contact disturbance
    IEC 60512-6-5:1997 Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 6: Dynamic stress tests - Section 5: Test 6e: Random vibration
    IEC 60512-14-7:1997 Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 14: Sealing tests - Section 7: Test 14g: Impacting water
    IEC 60512-16-5:2008 Connectors for electronic equipment - Tests and measurements - Part 16-5: Mechanical tests on contacts and terminations - Test 16e: Gauge retention force (resilient contacts)
    IEC 60512-12-5:2006 Connectors for electronic equipment - Tests and measurements - Part 12-5: Soldering tests - Test 12e: Resistance to soldering heat, soldering iron method
    IEC 60512-2-6:2002 Connectors for electronic equipment - Tests and measurements - Part 2-6: Electrical continuity and contact resistance tests - Test 2f: Housing (shell) electrical continuity
    IEC 60999-1:1999 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included)
    IEC 60352-1:1997 Solderless connections - Part 1: Wrapped connections - General requirements, test methods and practical guidance
    IEC 60512-2-2:2003 Connectors for electronic equipment - Tests and measurements - Part 2-2: Electrical continuity and contact resistance tests - Test 2b: Contact resistance - Specified test current method
    IEC 60512-6-2:2002 Connectors for electronic equipment - Tests and measurements - Part 6-2: Dynamic stress tests - Test 6b: Bump
    ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
    IEC 60512-11-3:2002 Connectors for electronic equipment - Tests and measurements - Part 11-3: Climatic tests - Test 11c: Damp heat, steady state
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 60352-8:2011 Solderless connections - Part 8: Compression mount connections - General requirements, test methods and practical guidance
    IEC 60512-1-1:2002 Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination
    IEC 60352-5:2012 Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance
    ISO 128-30:2001 Technical drawings General principles of presentation Part 30: Basic conventions for views
    IEC 60512-11-1:1995 Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 11: Climatic tests - Section 1: Test 11a - Climatic sequence
    IEC 60512-2-1:2002 Connectors for electronic equipment - Tests and measurements - Part 2-1: Electrical continuity and contact resistance tests - Test 2a: Contact resistance - Millivolt level method
    IEC 60512-9-1:2010 Connectors for electronic equipment - Tests and measurements - Part 9-1: Endurance tests - Test 9a: Mechanical operation
    IEC 60512-5-2:2002 Connectors for electronic equipment - Tests and measurements - Part 5-2: Current-carrying capacity tests - Test 5b: Current-temperature derating
    IEC 60512-19-3:1997 Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 19: Chemical resistance tests - Section 3: Test 19c - Fluid resistance
    IEC 60512-11-13:2002 Connectors for electronic equipment - Tests and measurements - Part 11-13: Climatic tests - Test 11n: Gas tightness, solderless wrapped connections
    IEC 60512-4-1:2003 Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stress tests - Test 4a: Voltage proof
    IEC 60352-2:2006+AMD1:2013 CSV Solderless connections - Part 2: Crimped connections - Generalrequirements, test methods and practical guidance
    IEC 60512-17-3:2010 Connectors for electronic equipment - Tests and measurements - Part 17-3: Cable clamping tests - Test 17c: Cable clamp resistance to cable pull (tensile)
    IEC 60512-17-4:2010 Connectors for electronic equipment - Tests and measurements - Part 17-4: Cable clamping tests - Test 17d: Cable clamp resistance to cable torsion
    IEC 60512-12-4:2006 Connectors for electronic equipment - Tests and measurements - Part 12-4: Soldering tests - Test 12d: Resistance to soldering heat, solder bath method
    IEC 60512-6-4:2002 Connectors for electronic equipment - Tests and measurements - Part 6-4: Dynamic stress tests - Test 6d: Vibration (sinusoidal)
    IEC 60512-15-6:2008 Connectors for electronic equipment - Tests and measurements - Part 15-6: Connector tests (mechanical) - Test 15f: Effectiveness of connector coupling devices
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    IEC 60050-581:2008 International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
    IEC 60998-2-1:2002 Connecting devices for low-voltage circuits for household and similar purposes - Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units
    IEC 60512-1-2:2002 Connectors for electronic equipment - Tests and measurements - Part 1-2: General examination - Test 1b: Examination of dimension and mass
    IEC 60352-7:2002 Solderless connections - Part 7: Spring clamp connections - General requirements, test methods and practical guidance
    IEC 60512-13-1:2006 Connectors for electronic equipment - Tests and measurements - Part 13-1: Mechanical operation tests - Test 13a: Engaging and separating forces
    IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective