Skip to content
Please enter a keyword to search

  • ISO 8062-3:2007

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  15-02-2023

    Language(s): 

    Published date:  31-05-2007

    Publisher:  International Organization for Standardization

    Add To Cart

    Abstract - (Show below) - (Hide below)

    ISO 8062-3:2007 specifies general dimensional and geometrical tolerances, as well as machining allowance grades, for castings as delivered to the purchaser in accordance with ISO 8062-2. It is applicable for the tolerancing of dimensions and geometry, and required machining allowance of castings in all cast metals and their alloys produced by various casting manufacturing processes.

    ISO 8062-3:2007 applies to both general dimensional and general geometrical tolerances, unless otherwise specified.

    The dimensional tolerances covered by ISO 8062-3:2007 are tolerances for linear dimensions.

    The geometrical tolerances covered by ISO 8062-3:2007 are:

    • tolerances for straightness,
    • flatness,
    • roundness,
    • parallelism,
    • perpendicularity,
    • symmetry, and
    • coaxiality.

    ISO 8062-3:2007 can be used for the selection of tolerance values for individual indications.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes ISO/DIS 8062-3 and ISO 8062. (06/2007)
    Document Type Standard
    Product Note THIS STANDARD ALSO REFER-ISO 14405
    Publisher International Organization for Standardization
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN 469:2014-06 CRANK HANDLES, STRAIGHT PATTERN
    09/30200834 DC : 0 BS EN 1559-1 - FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 1: GENERAL
    BS ISO 113:2010 Rolling bearings. Plummer block housings. Boundary dimensions
    UNI EN 10340 : 2008 STEEL CASTINGS FOR STRUCTURAL USES
    I.S. EN 15776:2011 UNFIRED PRESSURE VESSELS - REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM CAST IRON WITH AN ELONGATION AFTER FRACTURE EQUAL OR LESS THAN 15%
    BS EN ISO 14978:2006 Geometrical Product Specifications (GPS). General concepts and requirements for GPS measuring equipment
    DIN EN ISO 14405-2:2012-03 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 2: DIMENSIONS OTHER THAN LINEAR SIZES (ISO 14405-2:2011)
    I.S. EN ISO 14405-2:2011 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 2: DIMENSIONS OTHER THAN LINEAR SIZES (ISO 14405-2:2011)
    UNE-EN 15776:2011 Unfired pressure vessels - Requirements for the design and fabrication of pressure vessels and pressure parts constructed from cast iron with an elongation after fracture equal or less than 15 %
    UNE-EN ISO 14405-2:2015 Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear sizes (ISO 14405-2:2011)
    DIN EN 1982:2016-01 (Draft) COPPER AND COPPER ALLOYS - INGOTS AND CASTINGS
    EN 1706:2010 Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties
    UNE-EN 1559-1:2011 Founding - Technical conditions of delivery - Part 1: General
    UNE-EN 1706:2011 Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties
    BS EN 10340:2007 Steel castings for structural uses
    BS EN 15272-4:2007 Inland navigation vessels. Equipment for rope leading Rope lead
    BS EN 1559-1:2011 Founding. Technical conditions of delivery General
    CEN/TR 16749:2014 Aluminium and aluminium alloys - Classification of Defects and Imperfections in High Pressure, Low Pressure and Gravity Die Cast Products
    DIN SPEC 91184 E : 2014 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013)
    PREN 1090-3 : DRAFT 2017 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES
    DIN CEN ISO/TS 8062-2;DIN SPEC 91184:2014-03 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013)
    13/30252100 DC : 0 BS ISO 4990 - STEEL CASTINGS - GENERAL TECHNICAL DELIVERY REQUIREMENTS
    BS ISO 8062-4:2017 Geometrical product specifications (GPS). Dimensional and geometrical tolerances for moulded parts General tolerances for castings using profile tolerancing in a general datum system
    PD CEN ISO/TS 8062-2:2013 Geometrical Product Specifications (GPS). Dimensional and geometrical tolerances for moulded parts Rules
    16/30321444 DC : DRAFT SEP 2016 BS ISO 6482 - SHIPBUILDING - DECK MACHINERY - WARPING END PROFILES
    ISO 6482:2017 Shipbuilding — Deck machinery — Warping end profiles
    EN 13445-6 : 2014 COR 2017 UNFIRED PRESSURE VESSELS - PART 6: REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON
    DIN CEN ISO/TS 8062-2; DIN SPEC 91184:2014-03 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013)
    DIN 468:2014-06 CRANK HANDLES, OFFSET TYPE
    BS EN ISO 14405-2:2011 Geometrical product specifications (GPS). Dimensional tolerancing Dimensions other than linear sizes
    DIN EN 15776:2016-01 Unfired pressure vessels - Requirements for the design and fabrication of pressure vessels and pressure parts constructed from cast iron with an elongation after fracture equal or less than 15 % (includes Amendment A1:2015)
    I.S. EN 13445-6:2014 UNFIRED PRESSURE VESSELS - PART 6: REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON
    ISO 14405-2:2011 Geometrical product specifications (GPS) Dimensional tolerancing Part 2: Dimensions other than linear sizes
    UNI EN ISO 14978 : 2006 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GENERAL CONCEPTS AND REQUIREMENTS FOR GPS MEASURING EQUIPMENT
    EN 1982:2017 Copper and copper alloys - Ingots and castings
    DIN EN 1559-1:2011-05 Founding - Technical conditions of delivery - Part 1: General
    I.S. EN 1982:2017 COPPER AND COPPER ALLOYS - INGOTS AND CASTINGS
    I.S. EN 1559-1:2011 FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 1: GENERAL
    VDI 3120:2015-06 Cast steel wall thicknesses in large stamping and forming dies - Design references for tools with more than 1000 mm side length
    BS ISO 4990:2015 Steel castings. General technical delivery requirements
    DIN CEN/TR 16749;DIN SPEC 31601:2015-02 ALUMINIUM AND ALUMINIUM ALLOYS - CLASSIFICATION OF DEFECTS AND IMPERFECTIONS IN HIGH PRESSURE, LOW PRESSURE AND GRAVITY DIE CAST PRODUCTS
    UNI EN 15272-4 : 2008 INLAND NAVIGATION VESSELS - EQUIPMENT FOR ROPE LEADING - PART 4: ROPE LEAD
    UNI EN ISO 14405-2 : 2012 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 2: DIMENSIONS OTHER THAN LINEAR SIZES
    ISO 113:2010 Rolling bearings Plummer block housings Boundary dimensions
    S.R. CEN ISO/TS 8062-2:2013 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013, CORRECTED VERSION 2013-11-01)
    BS EN 15776 : 2011 UNFIRED PRESSURE VESSELS - REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM CAST IRON WITH AN ELONGATION AFTER FRACTURE EQUAL OR LESS THAN 15%
    ISO 8062-4:2017 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: General tolerances for castings using profile tolerancing in a general datum system
    I.S. EN ISO 14978:2006 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GENERAL CONCEPTS AND REQUIREMENTS FOR GPS MEASURING EQUIPMENT
    17/30347070 DC : 0 BS EN 10340-2 - STEEL CASTINGS FOR STRUCTURAL USES - PART 2: TECHNICAL DELIVERY CONDITIONS
    DIN EN 1706:2013-12 ALUMINIUM AND ALUMINIUM ALLOYS - CASTINGS - CHEMICAL COMPOSITION AND MECHANICAL PROPERTIES
    DIN EN 15272-4:2007-12 Inland navigation vessels - Equipment for rope leading - Part 4: Rope lead
    DIN EN 10340:2008-01 Steel castings for structural uses
    DIN EN ISO 14978:2006-09 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GENERAL CONCEPTS AND REQUIREMENTS FOR GPS MEASURING EQUIPMENT
    UNE-EN 1982:2018 Copper and copper alloys - Ingots and castings
    BS EN 1706:2010 Aluminium and aluminium alloys. Castings. Chemical composition and mechanical properties
    EN ISO 14978:2006/AC:2008 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GENERAL CONCEPTS AND REQUIREMENTS FOR GPS MEASURING EQUIPMENT
    UNI EN 1706 : 2010 ALUMINIUM AND ALUMINIUM ALLOYS - CASTINGS - CHEMICAL COMPOSITION AND MECHANICAL PROPERTIES
    UNI EN 1559-1 : 2011 FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 1: GENERAL
    DIN CEN/TR 16749;DIN SPEC 31601:2015-02 ALUMINIUM AND ALUMINIUM ALLOYS - CLASSIFICATION OF DEFECTS AND IMPERFECTIONS IN HIGH PRESSURE, LOW PRESSURE AND GRAVITY DIE CAST PRODUCTS
    08/30176073 DC : DRAFT APR 2008 BS EN 15776 - UNFIRED PRESSURE VESSELS - ADDITIONAL REQUIREMENTS FOR THE DE SIGN AND FABRICATION OF PRESSURE VESSELS AND PARTS CONSTRUCTED FROM CAST IRON WITH ELONGATION EQUAL OR LESS THAN 15 PERCENT
    17/30347067 DC : 0 BS EN 10340-1 - STEEL CASTINGS FOR STRUCTURAL USES - PART 1: GENERAL
    13/30274230 DC : 0 BS EN 13445-6:2009/A1 - UNFIRED PRESSURE VESSELS - REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON
    UNI CEN ISO/TS 8062-2 : 2013 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES
    BS ISO 6482:2017 Shipbuilding. Deck machinery. Warping end profiles
    BS EN 13445-6 : 2014 UNFIRED PRESSURE VESSELS - PART 6: REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON
    UNE-EN 13445-6:2015 Unfired pressure vessels - Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron
    ISO 14978:2006 Geometrical product specifications (GPS) General concepts and requirements for GPS measuring equipment
    17/30348949 DC : 0 BS EN 1090-3 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES
    PREN 10340-2 : DRAFT 2017 STEEL CASTINGS FOR STRUCTURAL USES - PART 2: TECHNICAL DELIVERY CONDITIONS
    ISO 4990:2015 Steel castings — General technical delivery requirements
    BS EN 1982:2017 Copper and copper alloys. Ingots and castings
    I.S. EN 1706:2010 ALUMINIUM AND ALUMINIUM ALLOYS - CASTINGS - CHEMICAL COMPOSITION AND MECHANICAL PROPERTIES
    EN 15776:2011+A1:2015 Unfired pressure vessels - Requirements for the design and fabrication of pressure vessels and pressure parts constructed from cast iron with an elongation after fracture equal or less than 15 %
    EN 1559-1:2011 Founding - Technical conditions of delivery - Part 1: General
    EN 15272-4:2007 Inland navigation vessels - Equipment for rope leading - Part 4: Rope lead
    PD CEN/TR 16749:2014 Aluminium and aluminium alloys. Classification of Defects and Imperfections in High Pressure, Low Pressure and Gravity Die Cast Products
    S.R. CEN/TR 16749:2014 ALUMINIUM AND ALUMINIUM ALLOYS - CLASSIFICATION OF DEFECTS AND IMPERFECTIONS IN HIGH PRESSURE, LOW PRESSURE AND GRAVITY DIE CAST PRODUCTS
    DIN EN 15776 E : 2016 UNFIRED PRESSURE VESSELS - REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM CAST IRON WITH AN ELONGATION AFTER FRACTURE EQUAL OR LESS THAN 15%
    DIN CEN ISO/TS 8062-2;DIN SPEC 91184:2014-03 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013)
    PREN 1559-1 : DRAFT 2009 FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 1: GENERAL
    EN ISO 14405-2:2011 Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear sizes (ISO 14405-2:2011)
    CEN ISO/TS 8062-2 : 2013 COR 2014 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013, CORRECTED VERSION 2013-11-01)
    ISO/TS 8062-2:2013 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2: Rules
    EN 10340:2007/AC:2008 STEEL CASTINGS FOR STRUCTURAL USES

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/TR 14638:1995 Geometrical product specification (GPS) Masterplan
    ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
    ISO 5459:2011 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
    ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
    ISO/TS 8062-2:2013 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2: Rules
    ISO 10135:2007 Geometrical product specifications (GPS) — Drawing indications for moulded parts in technical product documentation (TPD)
    ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
    ISO 8062-1:2007 Geometrical product specifications (GPS) Dimensional and geometrical tolerances for moulded parts Part 1: Vocabulary
    ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
    ISO 10579:2010 Geometrical product specifications (GPS) Dimensioning and tolerancing Non-rigid parts
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective