• SAE AMS 6325 : 2015

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    STEEL, BARS, AND FORGINGS 0.50CR - 0.55NI - 0.25MO (0.38 - 0.43C) (SAE 8740) HEAT TREATED, 105 KSI (724 MPA) TENSILE STRENGTH

    Available format(s):  Hardcopy, PDF

    Superseded date:  13-04-2020

    Language(s):  English

    Published date:  01-01-2015

    Publisher:  SAE International

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. APPLICABLE DOCUMENTS
    3. TECHNICAL REQUIREMENTS
    4. QUALITY ASSURANCE PROVISIONS
    5. PREPARATION FOR DELIVERY
    6. ACKNOWLEDGMENT
    7. REJECTIONS
    8. NOTES

    Abstract - (Show below) - (Hide below)

    Specifies an aircraft-quality, low-alloy steel in the form of heat treated bars and forgings.

    General Product Information - (Show below) - (Hide below)

    Committee AMS-E
    Development Note Supersedes MIL S 6049 (09/2002) Supersedes SAE AMS S 6049. (07/2006)
    Document Type Revision
    Publisher SAE International
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    17/30369678 DC : 0 PREN 7010 - AEROSPACE SERIES - USER GUIDE FOR CREATION AND DESIGNATION OF BOLTS
    MS21025 Revision F:1996 NUT, CASTELLATED, HEXAGON
    10/30227763 DC : 0 BS EN 6114 - AEROSPACE SERIES - BOLT, COUNTERSUNK HEAD, SHORT THREAD - INCH SERIES
    SAE AS 269J:2012:(S2018) IDENTIFICATION OF MATERIAL FOR AN, MS AND AS ENGINE AND PROPELLER STANDARD UTILITY PARTS AND ALSO FOR COMPANY PARTS
    10/30227764 DC : 0 BS EN 6115 - AEROSPACE SERIES - BOLT - PROTRUDING HEAD, SHORT THREAD - INCH SERIES
    MIL-DTL-8789 Revision G:2015 FITTING END, ATTACHABLE, HYDRAULIC, HIGH PRESSURE (3,000 PSI), GENERAL SPECIFICATION FOR

    Standards Referencing This Book - (Show below) - (Hide below)

    SAE AMS 2372 : 2014 QUALITY ASSURANCE SAMPLING AND TESTING, CARBON AND LOW-ALLOY STEEL FORGINGS
    SAE AMS 2370 : 2016 QUALITY ASSURANCE SAMPLING AND TESTING, CARBON AND LOW-ALLOY STEEL WROUGHT PRODUCTS AND FORGING STOCK
    ASTM E 384 : 2017 : REDLINE Standard Test Method for Microindentation Hardness of Materials
    SAE AMS 2251 : 2013 TOLERANCES, LOW-ALLOY STEEL BARS
    SAE AMS 2806D : 2013 IDENTIFICATION BARS, WIRE, MECHANICAL TUBING, AND EXTRUSIONS, CARBON AND ALLOY STEELS AND CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS
    SAE AMS 2301 : 2015 STEEL CLEANLINESS, AIRCRAFT QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE
    SAE AS 1182 : 2012 STANDARD STOCK REMOVAL ALLOWANCE AIRCRAFT-QUALITY AND PREMIUM AIRCRAFT-QUALITY STEEL BARS AND MECHANICAL TUBING
    SAE AMS 2750 : 2012 PYROMETRY
    ASTM E 350 : 2012-09 TEST METHODS FOR CHEMICAL ANALYSIS OF CARBON STEEL, LOW-ALLOY STEEL, SILICON ELECTRICAL STEEL, INGOT IRON, AND WROUGHT IRON
    SAE AMS 2759/1 : 2009 HEAT TREATMENT OF CARBON AND LOW-ALLOY STEEL PARTS, MINIMUM TENSILE STRENGTH BELOW 220 KSI (1517 MPA)
    ASTM E 381 : 2017 : REDLINE Standard Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings
    SAE AMS 2808 : 2017 IDENTIFICATION FORGINGS
    SAE AMS 2259 : 2012 CHEMICAL CHECK ANALYSIS LIMITS, WROUGHT LOW-ALLOY AND CARBON STEELS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective