UNI CEN/TS 13001-3-1 : 2005

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES

Available format(s):

Superseded date: 10-05-2012

Language(s):

Published date: 01-01-2005

Publisher: Ente Nazionale Italiano di Unificazione (UNI)

Table of Contents - (Show below) - (Hide below)

Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Proof of static strength
6 Proof of fatigue strength
7 Proof of static strength of hollow section girder joints
8 Proof of elastic stability
Annex A (normative) - Values of inverse slope m of
        [sigma]/N - curve and the value of the characteristic
        stress range [Delta][sigma][c], [Delta][tau][c]
Annex B (informative) - Guidance for selection of classes S
        due to experience
Annex C (normative) - Calculated values of permissible
        stress range [Delta][sigma][Rd]
Annex D (normative) - Design weld stress [sigma][W,Sd]
        and [tau][W,Sd]
Annex E (informative) - Hollow Sections
Annex F (informative) - Selection of a suitable set of crane
        standards for a given application
Bibliography

Abstract - (Show below) - (Hide below)

Describes general conditions, requirements and methods to prevent mechanical hazards of cranes by design and theoretical verification.

General Product Information - (Show below) - (Hide below)

Document Type	Standard
ISBN
Pages
Published
Publisher	Ente Nazionale Italiano di Unificazione (UNI)
Status	Superseded
Superseded By	UNI EN 13001-3-1 : 2013

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
CEN/TS 13001-3-1:2004/AC:2006	Identical

Standards Referencing This Book - (Show below) - (Hide below)

EN 10113-2 : 1993	HOT-ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - DELIVERY CONDITIONS FOR NORMALIZED/NORMALIZED ROLLED STEELS
ISO 2553:2013	Welding and allied processes Symbolic representation on drawings Welded joints
EN 10149-1:2013	Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions
ISO 4306-1:2007	Cranes — Vocabulary — Part 1: General
EN 10164:2004	Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
EN 10149-2:2013	Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels
EN 10025:1990/A1:1993	HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS
EN 12345 : 1998	WELDING - MULTILINGUAL TERMS FOR WELDED JOINTS WITH ILLUSTRATIONS
ISO 9013:2017	Thermal cutting — Classification of thermal cuts — Geometrical product specification and quality tolerances
EN 10045-1 : 1990	METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD
ISO 5817:2014	Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections
EN 10137-2 : 1995	PLATES AND WIDE FLATS MADE OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN THE QUENCHED AND TEMPERED OR PRECIPITATION HARDENED CONDITIONS - DELIVERY CONDITIONS FOR QUENCHED AND TEMPERED STEELS
EN 13001-2:2014	Crane safety - General design - Part 2: Load actions
EN 10113-1 : 1993	HOT ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - GENERAL DELIVERY CONDITIONS
EN ISO 12100-1:2003/A1:2009	SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
EN 13001-1:2015	Cranes - General design - Part 1: General principles and requirements
EN 22553:1994	Welded, brazed and soldered joints - Symbolic representation on drawings (ISO 2553:1992)
ISO 12100-2:2003	Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
EN ISO 12100-2:2003/A1:2009	SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
ISO 286-2:2010	Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
EN ISO 898-1:2013	Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
ISO 12100-1:2003	Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
EN 1990:2002/A1:2005/AC:2010	EUROCODE - BASIS OF STRUCTURAL DESIGN
EN ISO 9013:2017	Thermal cutting - Classification of thermal cuts - Geometrical product specification and quality tolerances (ISO 9013:2017)
EN 1070 : 1998	SAFETY OF MACHINERY - TERMINOLOGY
EN 10149-3:2013	Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels
EN 25817 : 1992	ARC WELDED JOINTS IN STEEL - GUIDANCE ON QUALITY LEVELS FOR IMPERFECTIONS
EN 1993-1-1:2005/A1:2014	EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
ISO 898-1:2013	Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread
EN 10113-3 : 1993	HOT ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - DELIVERY CONDITIONS FOR THERMOMECHANICAL ROLLED STEELS

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart