Skip to content
Please enter a keyword to search

  • UNI EN ISO 14405-2 : 2012

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 2: DIMENSIONS OTHER THAN LINEAR SIZES

    Available format(s): 

    Superseded date:  31-08-2022

    Language(s): 

    Published date:  31-12-2011

    Publisher:  Ente Nazionale Italiano di Unificazione (UNI)

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Principles and rules for indication of dimensions and
      related tolerances
    5 Units used in drawings for dimensions
    6 Indication of tolerances for linear and angular
      dimensions
    7 Illustrations of ambiguous +/- tolerancing vs - unambiguous
      geometrical tolerancing
    8 Angular tolerancing
    Annex A (informative) - Explanations and examples of the
            ambiguity caused by using +/- tolerances for
            dimensions other than linear size
    Annex B (informative) - Relation to the GPS matrix model
    Bibliography

    Abstract - (Show below) - (Hide below)

    Depicts the use of geometrical tolerancing for dimensions that are not linear sizes to avoid the ambiguity that the use of +/- tolerances on these dimensions causes.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher Ente Nazionale Italiano di Unificazione (UNI)
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/TR 14638:1995 Geometrical product specification (GPS) Masterplan
    ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
    ISO/TS 17450-2:2002 Geometrical product specifications (GPS) General concepts Part 2: Basic tenets, specifications, operators and uncertainties
    ISO 5459:2011 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
    ISO 2692:2014 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
    ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
    ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
    ISO 8062-3:2007 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings
    ISO 3040:2016 Geometrical product specifications (GPS) Dimensioning and tolerancing Cones
    ISO 17450-1:2011 Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification
    ISO 81714-1:2010 Design of graphical symbols for use in the technical documentation of products Part 1: Basic rules
    ISO 2538:1998 Geometrical Product Specifications (GPS) Series of angles and slopes on prisms
    ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
    ISO 14660-2:1999 Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature
    ISO 129-1:2004 Technical drawings Indication of dimensions and tolerances Part 1: General principles
    ISO 14660-1:1999 Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions
    ISO 14405-1:2016 Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
    ISO 14253-2:2011 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
    ISO 13715:2017 Technical product documentation Edges of undefined shape Indication and dimensioning
    ISO 5458:1998 Geometrical Product Specifications (GPS) Geometrical tolerancing Positional tolerancing
    ISO/R 1938:1971 ISO system of limits and fits Part II : Inspection of plain workpieces
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective