UNI EN ISO 204 : 2009

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST

Available format(s):

Superseded date: 05-09-2022

Language(s):

Published date: 31-12-2008

Publisher: Ente Nazionale Italiano di Unificazione (UNI)

Table of Contents - (Show below) - (Hide below)

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and designations
5 Principle
6 Apparatus
7 Test pieces
8 Test procedure
9 Determination of results
10 Test validity
11 Accuracy of the results
12 Test report
Annex A (informative) - Information concerning different
        types of thermocouples
Annex B (informative) - Information concerning methods
        of calibration of thermocouples
Annex C (normative) - Creep testing using test pieces with
        V or blunt circumferential notches
Annex D (informative) - Method of estimating the uncertainty
        of the measurement in accordance with the Guide to the
        expression of uncertainty in measurement (GUM)
Annex E (informative) - Representation of results and
        graphical extrapolation
Bibliography

Abstract - (Show below) - (Hide below)

Describes the method for the uninterrupted and interrupted creep tests and defines the properties of metallic materials which can be determined from these tests, in particular the creep elongation and the time of creep rupture, at a specified temperature.

General Product Information - (Show below) - (Hide below)

Development Note	Supersedes UNI EN 10291. (09/2009)
Document Type	Standard
ISBN
Pages
Published
Publisher	Ente Nazionale Italiano di Unificazione (UNI)
Status	Superseded
Superseded By	UNI EN ISO 204:2018
Supersedes	UNI EN 10291 : 2003

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
EN ISO 204:2009	Identical
ISO 204:2009	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

UNI/TS 11325-4 : 2013	PRESSURE EQUIPMENT - PUTTING INTO SERVICE AND USE OF PRESSURE EQUIPMENT AND ASSEMBLIES - PART 4: OPERATIONAL METHODS FOR THE INTEGRITY ASSESSMENT OF PRESSURE EQUIPMENT WORKING UNDER CREEP CONDITIONS RELATED TO THE ASSESSMENT PROCEDURE OF THE UNI/TS 11325-2

Standards Referencing This Book - (Show below) - (Hide below)

ISO/TS 4949:2016	Steel names based on letter symbols
ISO 783:1999	Metallic materials Tensile testing at elevated temperature
ISO/IEC Guide 25:1990	General requirements for the competence of calibration and testing laboratories
ISO 9513:2012	Metallic materials — Calibration of extensometer systems used in uniaxial testing
ISO 7500-2:2006	Metallic materials Verification of static uniaxial testing machines Part 2: Tension creep testing machines Verification of the applied force
ISO 286-2:2010	Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
IEC 60584-1:2013	Thermocouples - Part 1: EMF specifications and tolerances
ISO/IEC Guide 98-3:2008	Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)
EN 45001 : 1989	GENERAL CRITERIA FOR THE OPERATION OF TESTING LABORATORIES

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart