Skip to content
Please enter a keyword to search

  • VDI/VDE 2617 Blatt 13; VDI/VDE 2630 Blatt 1.3:2011-12

    Current The latest, up-to-date edition.

    VDI/VDE 2617 Blatt 13: Accuracy of coordinate measuring machines - Characteristics and their testing - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors - VDI/VDE 2630 Blatt 1.3: Computed tomography in dimensional measurement - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors

    Available format(s):  Hardcopy, PDF

    Language(s):  German - English

    Published date:  01-12-2011

    Publisher:  Verlag des Vereins Deutscher Ingenieure

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Preliminary note
    Introduction
    1 Scope
    2 Fundamentals
    3 Sensor types
    4 Acceptance test
    5 Monitoring
    6 Material- and geometry-dependent
      effects
    Annex A - Structural resolution for
              dimensional measurements
    Annex B - Synopsis: Old and new notation
              of symbols
    Bibliography

    Abstract - (Show below) - (Hide below)

    The purpose of this guideline is to define specifica-tions and procedures for testing coordinate measur-ing machines (CMMs) with sensors relying on the principle of X-ray computed tomography (CT sen-sors) (see VDI/VDE 2630 Part 1.1 for a definition).

    General Product Information - (Show below) - (Hide below)

    Development Note Also available as VDI/VDE 2630-1-3. (08/2009)
    Document Type Standard
    Publisher Verlag des Vereins Deutscher Ingenieure
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    VDI/VDE 2630 Blatt 1.1:2016-11 Computed tomography in dimensional measurement - Fundamentals and definitions
    VDI/VDE 2617 Blatt 5:2010-12 Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with artefacts
    VDI/VDE 2617 Blatt 2.1:2014-03 Accuracy of coordinate measuring machines - Parameters and their reverification - Code of practice for the application of DIN EN ISO 10360-2 for length measurement
    VDI/VDE 2617 Blatt 11:2011-03 Accuracy of coordinate measuring machines - Characteristics and their checking - Determination of the uncertainty of measurement for coordinate measuring machines using uncertainty budgets
    VDI/VDE 2630 Blatt 1.2:2010-11 Computed tomography in dimensional measurement - Influencing variables on measurement results and recommendations for computed tomography dimensional measurements
    VDI/VDE 2630 Blatt 2.1:2015-06 Computed tomography in dimensional measurement - Determination of the uncertainty of measurement and the test process suitability of coordinate measurement systems with CT sensors
    VDI/VDE 2617 Blatt 5.1:2011-01 Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with ball plates

    Standards Referencing This Book - (Show below) - (Hide below)

    DIN EN ISO 1:2015-03 (Draft) GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - STANDARD REFERENCE TEMPERATURE FOR THE SPECIFICATION OF GEOMETRICAL AND DIMENSIONAL PROPERTIES (ISO 1:2016)
    DIN EN ISO 10360-4:2003-06 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE TEST AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 4: CMMS USED IN SCANNING MODE
    ISO 10360-4:2000 Geometrical Product Specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 4: CMMs used in scanning measuring mode
    DIN EN ISO 10360-9:2014-04 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING SYSTEMS (CMS) - PART 9: CMMS WITH MULTIPLE PROBING SYSTEMS (ISO 10360-9:2013)
    ISO 10360-6:2001 Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 6: Estimation of errors in computing Gaussian associated features
    EN ISO 10360-1:2000/AC:2002 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 1: VOCABULARY
    EN ISO 3650:1998 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - LENGTH STANDARDS - GAUGE BLOCKS
    DIN EN ISO 10360-1:2003-07 Geometrical Product Specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 1: Vocabulary (ISO 10360-1:2000 + Corr 1:2002) (includes Corrigendum AC:2002); German version EN ISO 10360-1:2000 + AC:2002
    DIN ISO/TS 23165:2008-08
    DIN EN ISO 10360-7:2011-09 Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 7: CMMs equipped with imaging probing systems (ISO 10360-7:2011)
    ISO 10360-1:2000 Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 1: Vocabulary
    ISO 1:2016 Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties
    DIN EN ISO 14253-1:2013-12 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INSPECTION BY MEASUREMENT OF WORKPIECES AND MEASURING EQUIPMENT - PART 1: DECISION RULES FOR PROVING CONFORMITY OR NONCONFORMITY WITH SPECIFICATIONS (ISO 14253-1:2013)
    ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
    VDI/VDE 2617 Blatt 9:2009-06 Accuracy of coordinate measuring machines - Characteristics and their reverification - Acceptance and reverification tests for Articulated Arm Coordinate Measuring Machines
    ISO 3650:1998 Geometrical Product Specifications (GPS) Length standards Gauge blocks
    VDI/VDE 2617 Blatt 2.2:2000-07 Accuracy of coordinate measuring machines - Parameters and their reverification - Form measurement
    EN ISO 10360-4:2000/AC:2002 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 4: CMMS USED IN SCANNING MEASURING MODE
    DIN EN ISO 10360-2:2010-06 Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 2: CMMs used for measuring linear dimensions (ISO 10360-2:2009)
    VDI/VDE 2617 Blatt 5:2010-12 Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with artefacts
    VDI 1000:2017-02 VDI Standardisation Work - Principles and procedures
    VDI/VDE 2617 Blatt 7:2008-09 Accuracy of coordinate measuring machines - Parameters and their checking - Estimation of measurement uncertainty of coordinate measuring machines by means of simulation
    DIN EN ISO 10360-5:2011-01 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 5: CMMS USING SINGLE AND MULTIPLE STYLUS CONTACTING PROBING SYSTEMS
    VDI/VDE 2617 Blatt 2.1:2014-03 Accuracy of coordinate measuring machines - Parameters and their reverification - Code of practice for the application of DIN EN ISO 10360-2 for length measurement
    VDI/VDE 2630 Blatt 1.4:2010-06 Computed tomography in dimensional metrology - Measurement procedure and comparability
    VDI/VDE 2617 Blatt 6.3:2008-12 Accuracy of coordinate measuring machines - Characteristics and their checking - Coordinate measuring machines with multiple probing systems
    VDI/VDE 2617 Blatt 10:2011-01 Accuracy of coordinate measuring machines - Characteristics and their checking - Acceptance and reverification tests of lasertrackers
    VDI/VDE 2630 Blatt 1.2:2010-11 Computed tomography in dimensional measurement - Influencing variables on measurement results and recommendations for computed tomography dimensional measurements
    EN ISO 10360-3 : 2000 GEOMETRICAL PRODUCTS SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 3: CMMS WITH THE AXIS OF A ROTARY TABLE AS THE FOURTH AXIS (ISO 10360-3:2000)
    ENV 13005 : DRAFT 1999 GUIDE TO THE EXPRESSION OF UNCERTAINTY IN MEASUREMENT
    VDI/VDE 2630 Blatt 1.1:2016-11 Computed tomography in dimensional measurement - Fundamentals and definitions
    DIN EN ISO 10360-3:2000-08 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE TEST AND REVERIFICATION TEST FOR COORDINATE MEASURING MACHINES (CMM) - PART 3: CMMS WITH THE AXIS OF A ROTARY TABLE AS THE FOURTH AXIS
    DIN EN ISO 10360-6:2009-01 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 6: ESTIMATION OF ERRORS IN COMPUTING GAUSSIAN ASSOCIATED FEATURES
    EN ISO 10360-2:2009 Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 2: CMMs used for measuring linear dimensions (ISO 10360-2:2009)
    EN ISO 10360-7:2011 Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 7: CMMs equipped with imaging probing systems (ISO 10360-7:2011)
    DIN EN ISO 10360-8:2014-03 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING SYSTEMS (CMS) - PART 8: CMMS WITH OPTICAL DISTANCE SENSORS (ISO 10360-8:2013)
    ISO 10360-7:2011 Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 7: CMMs equipped with imaging probing systems
    VDI/VDE 2617 Blatt 5.1:2011-01 Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with ball plates
    VDI/VDE 2617 Blatt 6.1:2007-05 Accuracy of coordinate measuring machines - Characteristics and their testing - Coordinate measuring machines with optical probing - Code of practice for the application of DIN EN ISO 10360 to coordinate measuring machines with optical sensors for lateral structures
    VDI/VDE 2617 Blatt 8:2006-07 Accuracy of coordinate measuring machines - Characteristics and their testing - Test suitability of measurements with coordinate measuring machines
    VDI/VDE 2617 Blatt 2.3:2006-05 Accuracy of coordinate measuring machines - Characteristics and checking of characteristics - Acceptance and reverification tests for coordinate measuring machines of large dimensions
    ISO 10360-3:2000 Geometrical Product Specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 3: CMMs with the axis of a rotary table as the fourth axis
    VDI/VDE 2617 Blatt 12.1:2011-03 Accuracy of coordinate measuring machines - Characteristics and their checking - Acceptance and reverification tests for tactile CMM measuring microgeometries
    VDI/VDE 2617 Blatt 11:2011-03 Accuracy of coordinate measuring machines - Characteristics and their checking - Determination of the uncertainty of measurement for coordinate measuring machines using uncertainty budgets
    EN ISO 10360-6:2001/AC:2008 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 6: ESTIMATION OF ERRORS IN COMPUTING GAUSSIAN ASSOCIATED FEATURES (ISO 10360-6:2001/Cor 1:2007)
    EN ISO 10360-5:2010 Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 5: CMMs using single and multiple stylus contacting probing systems (ISO 10360-5:2010)
    PREN ISO 10360-9 : DRAFT 2010 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 9: CMMS WITH MULTIPLE PROBING SYSTEMS
    ISO 10360-5:2010 Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 5: CMMs using single and multiple stylus contacting probing systems
    EN ISO 1:2016 (edition 2) Geometrical product specifications (GPS) - Standard reference temperature for the specification of geometrical and dimensional properties (ISO 1:2016)
    ISO 10360-2:2009 Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 2: CMMs used for measuring linear dimensions
    ISO/TS 23165:2006 Geometrical product specifications (GPS) — Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective