Skip to content
Please enter a keyword to search

  • ASTM B 233 : 1997 : R2016

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes

    Available format(s):  Hardcopy, PDF

    Superseded date:  13-11-2021

    Language(s):  English

    Published date:  13-10-2016

    Publisher:  American Society for Testing and Materials

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 02.03, 2017 Covers aluminum 1350 drawing stock 0.375 in. (9.52 mm) to 1.000 in. (25.40 mm) in diameter for drawing into wire for electrical conductors.

    Scope - (Show below) - (Hide below)

    1.1This specification covers aluminum 1350 drawing stock 0.375 in. (9.52 mm) to 1.000 in. (25.40 mm) in diameter, in the tempers shown in Table 1, for drawing into wire for electrical conductors (Explanatory Note 1 and Note 2).

    (A)Applicable to stock sizes through 0.500-in. (12.70-mm) diameter. The values to apply for larger sizes in these tempers shall be negotiated at time of inquiry.

    1.2The SI values of density and resistivity are to be regarded as the standard. For all other properties the inch-pound values are to be regarded as standard and the SI units may be approximate.

    Note 1:Prior to 1975, aluminum 1350 was designated as EC aluminum.

    Note 2:The aluminum and temper designations conform to ANSI H35.1. Aluminum 1350 corresponds to unified numbering system A91350 in accordance with Practice E527.

    (A)Analysis shall regularly be made only for the elements specified in this table. If, however, the presence of other elements is suspected or indicated in amounts greater than the specified limits, further analysis shall be made to determine that these elements are not present in amounts in excess of the specified limits.
    (A)The equivalent resistivity values for 100 % IACS conductivity were each computed from the fundamental IEC value (1/58 Ω·mm2/m) using conversion factors each accurate to at least seven significant figures. Corresponding values for other conductivities (aluminum) were derived from these by multiplying by the reciprocal of the conductivity ratios accurate to at least seven significant figures.
    (A)For this specification, mean diameter is the average of the maximum diameter and the minimum diameter measured in the same transverse plane along the length.

    General Product Information - (Show below) - (Hide below)

    Committee B 01
    Document Type Standard
    Product Note Reconfirmed 2016
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM B 609/B609M : 2012 : R2016 Standard Specification for Aluminum 1350 Round Wire, Annealed and Intermediate Tempers, for Electrical Purposes

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM B 830 : 1997 Standard Specification for Uniform Test Methods and Frequency
    ASTM B 557 : 2015 : REDLINE Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
    ASTM E 527 : 2016 : REDLINE Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
    ASTM E 227 : 1990 : R1996 Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique (Withdrawn 2002)
    ASTM B 557 : 1994 Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
    ANSI H35.1 : 2006 ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM
    ASTM B 193 : 2016 : REDLINE Standard Test Method for Resistivity of Electrical Conductor Materials
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective