Skip to content
Please enter a keyword to search

  • BS EN 12619:2013

    Current The latest, up-to-date edition.

    Stationary source emissions. Determination of the mass concentration of total gaseous organic carbon. Continuous flame ionisation detector method

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  31-01-2013

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 The principle of the technique
    5 Requirements for apparatus and gases
    6 Measurement procedure
    Annex A (normative) - Determination of the performance
            characteristics of a FID
    Annex B (informative) - Basic functionality of an FID
    Annex C (informative) - Measurement uncertainty and
            associated statistics
    Annex D (informative) - Safety measures
    Annex E (informative) - Significant technical changes
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the requirements for an instrument using flame ionisation detection, together with procedures for its operation.

    Scope - (Show below) - (Hide below)

    This European Standard specifies a flame ionisation detector (FID) method. It is intended for use as a standard reference method for the measurement of the mass concentration of gaseous and vaporous organic substances (expressed as TVOC) in stationary source emissions (e.g. emissions from waste incinerators and solvent using processes, emission measurements according to 2010/75/EU) in the concentration range up to 1000mg/m³.

    This European Standard specifies the requirements for an instrument using flame ionisation detection, together with procedures for its operation. The results obtained using this standard are expressed in milligrams per cubic metre (mg/m³) as total carbon (TVOC).

    This European Standard is not applicable for permanently installed automated measuring systems (AMS).

    Alternative methods to this method may be used provided that the user can demonstrate equivalence, based on the principles of CEN/TS 14793.

    General Product Information - (Show below) - (Hide below)

    Committee EH/2/1
    Development Note Supersedes 96/563986 DC. (08/2005) Supersedes BS EN 13526 & 11/30238654 DC. (02/2013)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 5725-1:1994 Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions
    EN 15267-3:2007 Air quality - Certification of automated measuring systems - Part 3: Performance criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources
    CEN/TS 14793:2005 Stationary source emission - Intralaboratory validation procedure for an alternative method compared to a reference method
    ISO 14956:2002 Air quality Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty
    EN ISO 9169:2006 Air quality - Definition and determination of performance characteristics of an automatic measuring system (ISO 9169:2006)
    EN 15267-2:2009 Air quality - Certification of automated measuring systems - Part 2: Initial assessment of the AMS manufacturer’s quality management system and post certification surveillance for the manufacturing process
    EN 14789:2017 Stationary source emissions - Determination of volume concentration of oxygen - Standard reference method: Paramagnetism
    EN 15259:2007 Air quality - Measurement of stationary source emissions - Requirements for measurement sections and sites and for the measurement objective, plan and report
    EN 14181:2014 Stationary source emissions - Quality assurance of automated measuring systems
    EN ISO 14956 : 2002 AIR QUALITY - EVALUATION OF THE SUITABILITY OF A MEASUREMENT PROCEDURE BY COMPARISON WITH A REQUIRED MEASUREMENT UNCERTAINTY
    ENV 13005 : DRAFT 1999 GUIDE TO THE EXPRESSION OF UNCERTAINTY IN MEASUREMENT
    EN 14790:2017 Stationary source emissions - Determination of the water vapour in ducts - Standard reference method
    EN 15267-1:2009 Air quality - Certification of automated measuring systems - Part 1: General principles
    ISO 9169:2006 Air quality Definition and determination of performance characteristics of an automatic measuring system
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective