Skip to content
Please enter a keyword to search

  • PD ISO/TR 10017:2003

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Guidance on statistical techniques for ISO 9001:2000

    Available format(s):  Hardcopy, PDF

    Superseded date:  20-07-2021

    Language(s):  English

    Published date:  19-06-2003

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 Scope
    2 Terms and definitions
    3 Identification of potential needs for statistical
        techniques
    4 Descriptions of statistical techniques identified
        4.1 General
        4.2 Descriptive statistics
        4.3 Design of experiments
        4.4 Hypothesis testing
        4.5 Measurement analysis
        4.6 Process capability analysis
        4.7 Regression analysis
        4.8 Reliability analysis
        4.9 Sampling
        4.10 Simulation
        4.11 SPC charts (Statistical Process Control
              charts)
        4.12 Statistical tolerancing
        4.13 Time series analysis
    Annex A Overview of statistical techniques that could be
            used to support the requirements of clauses of
            ISO 9001
    Bibliography

    Abstract - (Show below) - (Hide below)

    Gives guidance for selecting appropriate statistical techniques of possible use to an organization for development, implementation or maintenance of a quality system to comply with ISO 9001. This is achieved by examination of the requirements of ISO 9001 involving use of quantitative data, followed by identification and description of those statistical techniques useful when applied to such data.

    General Product Information - (Show below) - (Hide below)

    Committee QS/1
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61025:2006 Fault tree analysis (FTA)
    ISO 5725-1:1994 Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions
    ISO 11843-2:2000 Capability of detection — Part 2: Methodology in the linear calibration case
    IEC 61123:1991 Reliability testing - Compliance test plans for success ratio
    ISO 2859-4:2002 Sampling procedures for inspection by attributes Part 4: Procedures for assessment of declared quality levels
    ISO 10725:2000 Acceptance sampling plans and procedures for the inspection of bulk materials
    IEC 60863:1986 Presentation of reliability, maintainability and availability predictions
    ISO 2859-3:2005 Sampling procedures for inspection by attributes — Part 3: Skip-lot sampling procedures
    ISO/TS 14253-2:1999 Geometrical Product Specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
    ISO 11843-1:1997 Capability of detection Part 1: Terms and definitions
    ISO 7873:1993 Control charts for arithmetic average with warning limits
    ISO 2854:1976 Statistical interpretation of data — Techniques of estimation and tests relating to means and variances
    ISO 16269-7:2001 Statistical interpretation of data — Part 7: Median — Estimation and confidence intervals
    IEC 60812:2006 Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)
    ISO 3951:1989 Sampling procedures and charts for inspection by variables for percent nonconforming
    IEC 61649:2008 Weibull analysis
    IEC 61014:2003 Programmes for reliability growth
    ISO/IEC Guide 43-1:1997 Proficiency testing by interlaboratory comparisons Part 1: Development and operation of proficiency testing schemes
    IEC 61070:1991 Compliance test procedures for steady-state availability
    ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
    IEC 61078:2016 Reliability block diagrams
    IEC 61165:2006 Application of Markov techniques
    ISO 7870:1993 Control charts General guide and introduction
    ISO 5725-3:1994 Accuracy (trueness and precision) of measurement methods and results — Part 3: Intermediate measures of the precision of a standard measurement method
    ISO Guide 33:2015 Reference materials Good practice in using reference materials
    ISO 11648-2:2001 Statistical aspects of sampling from bulk materials — Part 2: Sampling of particulate materials
    ISO 2859-2:1985 Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
    ISO 5725-6:1994 Accuracy (trueness and precision) of measurement methods and results — Part 6: Use in practice of accuracy values
    ISO Guide 35:2017 Reference materials Guidance for characterization and assessment of homogeneity and stability
    ISO 2859-0:1995 Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system
    IEC 61163-1:2006 Reliability stress screening - Part 1: Repairable assemblies manufactured in lots
    ISO 5725-4:1994 Accuracy (trueness and precision) of measurement methods and results Part 4: Basic methods for the determination of the trueness of a standard measurement method
    ISO 11095:1996 Linear calibration using reference materials
    ISO 2602:1980 Statistical interpretation of test results Estimation of the mean Confidence interval
    ISO 8422:2006 Sequential sampling plans for inspection by attributes
    IEC 61163-2:1998 Reliability stress screening - Part 2: Electronic components
    ISO 3301:1975 Statistical interpretation of data — Comparison of two means in the case of paired observations
    ISO 3534-2:2006 Statistics Vocabulary and symbols Part 2: Applied statistics
    IEC 61124:2012 Reliability testing - Compliance tests for constant failure rate and constant failure intensity
    ISO/TR 13425:2006 Guidelines for the selection of statistical methods in standardization and specification
    ISO 9004:2009 Managing for the sustained success of an organization A quality management approach
    ISO/TR 8550:1994 Guide for the selection of an acceptance sampling system, scheme or plan for inspection of discrete items in lots
    IEC 61164:2004 Reliability growth - Statistical test and estimation methods
    ISO 7966:1993 Acceptance control charts
    ISO 8423:2008 Sequential sampling plans for inspection by variables for percent nonconforming (known standard deviation)
    IEC 60300-1:2014 Dependability management - Part 1: Guidance for management and application
    ISO 3494:1976 Statistical interpretation of data — Power of tests relating to means and variances
    ISO 10012:2003 Measurement management systems — Requirements for measurement processes and measuring equipment
    ISO 5725-2:1994 Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method
    ISO 9001:2015 Quality management systems — Requirements
    IEC 60300-2:2004 Dependability management - Part 2: Guidelines for dependability management
    ISO 3534-3:2013 Statistics — Vocabulary and symbols — Part 3: Design of experiments
    IEC 60300-3-9:1995 Dependability management - Part 3: Application guide - Section 9: Risk analysis of technological systems
    ISO 5479:1997 Statistical interpretation of data — Tests for departure from the normal distribution
    ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
    ISO 11462-1:2001 Guidelines for implementation of statistical process control (SPC) Part 1: Elements of SPC
    ISO 8595:1989 Interpretation of statistical data Estimation of a median
    IEC 61650:1997 Reliability data analysis techniques - Procedures for comparison of two constant failure rates and two constant failure (event) intensities
    ISO/IEC Guide 43-2:1997 Proficiency testing by interlaboratory comparisons Part 2: Selection and use of proficiency testing schemes by laboratory accreditation bodies
    ISO/TR 7871:1997 Cumulative sum charts Guidance on quality control and data analysis using CUSUM techniques
    ISO 5725-5:1998 Accuracy (trueness and precision) of measurement methods and results — Part 5: Alternative methods for the determination of the precision of a standard measurement method
    ISO 3534-1:2006 Statistics — Vocabulary and symbols — Part 1: General statistical terms and terms used in probability
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective