Skip to content
Please enter a keyword to search

  • DEFSTAN 13-92/3(1996) : 1996

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    MANUFACTURE, INSPECTION AND PROOF OF ORDNANCE OF 20 MM CALIBRE AND OVER

    Available format(s):  Hardcopy, PDF

    Superseded date:  20-05-2005

    Language(s):  English

    Published date:  01-01-1996

    Publisher:  UK Ministry of Defence Standards

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Preface
    Section One - General
    1 Scope
    2 WARNING
    3 Related Documents
    4 Definitions
    Section Two - Manufacture
    5 Material
    6 Construction
    7 Testing
    8 Inspection Before Assembly
    9 Departure from Design
    10 Concentricity and Straightness
    11 Pressing
    12 Breech Mechanisms
    13 Interchangeability
    Section Three - Inspection and Examination
    14 Requirement
    15 Bore and Chamber
    16 Limits of Acceptance
    17 Surface Treatments
    Section Four - Proof of Ordnance
    18 Proof Requirements
    19 Preparation
    20 Proof Data Requirement
    21 Proof Pressures
    22 Rounds to be Fired
    23 Projectiles
    24 The Firing of Additional Rounds
    25 Variations and Exceptions
    26 Submission for Reproof
    Section Five - Identification
    27 Forging Numbers
    28 Registered Numbers
    29 Other Markings
    30 Marking and Badging
    Annex A - Bore Alignment and Measurement Limits
    Annex B - Charges to be Fired at Proof of Ordnance or
              Associated Parts
    Annex C - Service Ordnance Proof Pressures
    Annex D - Markings on Ordnance

    Abstract - (Show below) - (Hide below)

    Gives the conditions governing the manufacture of ordnance and associated components.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes DEFSTAN 13-92/2(1984) (06/2001) This standard is obsolescent because it is no longer required for procurement of new equipment but is retained for maintenance purposes in support of existing in-service equipment. (05/2016)
    Document Type Standard
    Publisher UK Ministry of Defence Standards
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    DEFSTAN 05-61(PT17)/1(1992) : 1992 QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 17: PROOF OF EXPLOSIVE OPERATED DEVICES THAT DISCHARGE PROJECTILES
    DEFSTAN 05-101(PT1)/1(2005) : 2005 PROOF OF ORDNANCE, MUNITIONS, ARMOUR AND EXPLOSIVES - PART 1: REQUIREMENTS
    DEFSTAN 10-13/3(1999) : 1999 STEEL FORGINGS FOR GUNS
    DEFSTAN 10-13/4(2005) : 2005 STEEL FORGINGS FOR GUNS
    DEFSTAN 07-85(PT1)/3(2006) : 2006 DESIGN REQUIREMENTS FOR WEAPONS AND ASSOCIATED SYSTEMS - PART 1: MANDATORY DESIGN REQUIREMENTS
    DEFSTAN 05-101(PT2)/1(2005) : 2005 PROOF OF ORDNANCE, MUNITIONS, ARMOUR AND EXPLOSIVES - PART 2: GUIDANCE
    DEFSTAN 07-085(PT1)/4(2017) : 2017 DESIGN REQUIREMENTS FOR WEAPONS AND ASSOCIATED SYSTEMS - PART 1: MANDATORY DESIGN REQUIREMENTS
    DEFSTAN 05-61(PT11)/2(1992) : 1992 QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 11: PROOF SENTENCING
    DEFSTAN 05-61(PT14)/1(1994) : 1994 QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 14: PROOF SCHEDULES FOR CONVENTIONAL WEAPONS, AMMUNITION AND EXPLOSIVE ITEMS OF NEW MANUFACTURE

    Standards Referencing This Book - (Show below) - (Hide below)

    STANAG 4224 : 2007 LARGE CALIBRE ARTILLERY AND NAVAL GUN AMMUNITION GREATER THAN 40 MM, SAFETY AND SUITABILITY FOR SERVICE EVALUATION
    DEFSTAN 05-61(PT1)/3(1998) : 1998 QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 1: DEVIATION/PRODUCTION PERMITS AND WAIVERS/CONCESSIONS - QUALITY ASSURANCE OF SUBCONTRACT WORK
    DEFSTAN 13-36(PT8)/1(1991) : INTERIM BALLISTIC STANDARDIZATION OF GUN AMMUNITION - PART 8: CRUSHERS AND CRUSHER GAUGES
    DEFSTAN 05-61(PT14)/1(1994) : 1994 QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 14: PROOF SCHEDULES FOR CONVENTIONAL WEAPONS, AMMUNITION AND EXPLOSIVE ITEMS OF NEW MANUFACTURE
    BS 3811:1993 Glossary of terms used in terotechnology
    BS 4778(1979) : LATEST QUALITY VOCABULARY
    DEFSTAN 10-13/3(1999) : 1999 STEEL FORGINGS FOR GUNS
    STANAG 4225 : 0 THE SAFETY EVALUATION OF MORTAR BOMBS
    STANAG 4110 : 2005 DEFINITIONS OF PRESSURE TERMS AND THEIR INTERRELATIONSHIP FOR USE IN THE DESIGN AND PROOF OF CANNONS OR MORTARS AND AMMUNITION
    DEFSTAN 05-61(PT11)/2(1992) : 1992 QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 11: PROOF SENTENCING
    DEFSTAN 05-61(PT13)/1(1994) : 1994 QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 13: ACCEPTANCE PROCEDURES FOR PROOF EQUIPMENT
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective