Skip to content
Please enter a keyword to search

  • DIN EN ISO 306 E : 2014

    Current The latest, up-to-date edition.

    PLASTICS - THERMOPLASTIC MATERIALS - DETERMINATION OF VICAT SOFTENING TEMPERATURE (VST) (ISO 306:2013)

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2014

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National foreword
    National Annex NA (informative) - Bibliography
    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Principle
    5 Apparatus
    6 Test frame assembly calibration
    7 Test specimens
    8 Conditioning
    9 Procedure
    10 Precision
    11 Test report
    Annex A (informative) - Comparison of VST results obtained with
            liquid-filled heating bath and direct-contact heating unit
    Annex B (informative) - Comparison of VST results obtained with
            liquid-filled heating bath and fluidized bed
    Annex C (informative) - Repeatability and precision
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes four methods for the determination of the Vicat softening temperature (VST) of thermoplastic materials: - method A50 using a force of 10 N and a heating rate of 50 K/h; - method B50 using a force of 50 N and a heating rate of 50 K/h; - method A120 using a force of 10 N and a heating rate of 120 K/h; - method B120 using a force of 50 N and a heating rate of 120 K/h.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Current
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN EN ISO 20753 E : 2014 PLASTICS - TEST SPECIMENS (ISO 20753:2008)
    DIN EN ISO 11296-7:2013-05 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES (ISO 11296-7:2011)
    DIN EN ISO 11833-1:2012-11 PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM (ISO 11833-1:2012)
    DIN 30678:2013-09 Polypropylene coatings on steel pipes and fittings - Requirements and testing
    DIN EN ISO 11833-2:2006-06 Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 2: Sheets of thickness less than 1 mm (ISO 11833-2:1998)
    DIN EN ISO 11963:2013-03 PLASTICS - POLYCARBONATE SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS (ISO 11963:2012)
    DIN EN ISO 11439:2013-09 Gas cylinders - High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles (ISO 11439:2013)
    DIN EN ISO 11296-7 E : 2013 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES (ISO 11296-7:2011)
    DIN EN ISO 14910-2 E : 2013 PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013)
    DIN EN ISO 25137-2 E : 2017 PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009)
    DIN EN ISO 14910-2:2013-06 PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013)

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
    ISO 294-3:2002 Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates
    DIN EN ISO 20753:2014-07 PLASTICS - TEST SPECIMENS (ISO 20753:2008)
    ISO 472:2013 Plastics Vocabulary
    ISO 294-2:1996 Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars
    DIN EN ISO 291 E : 2008 PLASTICS - STANDARD ATMOSPHERES FOR CONDITIONING AND TESTING
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    ISO 5725-2:1994 Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method
    ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
    ISO 2818:1994 Plastics — Preparation of test specimens by machining
    DIN EN ISO 293 E : 2005 PLASTICS - COMPRESSION MOULDING TEST SPECIMENS OF THERMOPLASTIC MATERIALS
    ISO 20753:2008 Plastics Test specimens
    DIN EN ISO 472:2013-06 PLASTICS - VOCABULARY (ISO 472:2013)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective