Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN 60603-7:2009

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS (IEC 60603-7:2008)

    Available format(s):  Hardcopy, PDF

    Superseded date:  23-11-2021

    Language(s):  English

    Published date:  01-01-2009

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 General
    2 Terms and definitions
    3 Common features and typical connector pair
    4 Cable terminations and internal connections - Fixed
      and free connectors
    5 Gauges
    6 Characteristics
    7 Tests and test schedule
    Annex A (normative) - Gauging continuity procedure
    Annex B (normative) - Locking-device mechanical operation
    Annex C (normative) - Gauge requirements
    Annex D (normative) - Keystone connector information
    Annex ZA (normative) - Normative references to international
             publications with their corresponding European
             publications
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines 8-way unshielded free and fixed connectors and is intended to specify the common dimensions, mechanical, electrical and environmental characteristics and tests for the family of IEC 60603-7-x connectors.

    General Product Information - (Show below) - (Hide below)

    Committee TC 48
    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Product Note CSV VERSION IS NOW AVAILABLE FOR THIS STANDARD The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document.
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61076-1:2006 Connectors for electronic equipment - Product requirements - Part 1: Generic specification
    EN 60352-2:2006/A1:2013 SOLDERLESS CONNECTIONS - PART 2: CRIMPED CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE
    IEC 60352-3:1993 Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance
    IEC 60603-7-71:2010 Connectors for electronic equipment - Part 7-71: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 1 000 MHz
    IEC 60352-6:1997 Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    EN 60512-1-100:2012 Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications
    IEC 60603-7-2:2010 Connectors for electronic equipment - Part 7-2: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz
    EN 60352-3:1994 Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance
    EN ISO 1302 : 2002 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INDICATION OF SURFACE TEXTURE IN TECHNICAL PRODUCT DOCUMENTATION (ISO 1302:2002)
    EN 60068-1:2014 Environmental testing - Part 1: General and guidance
    ISO/IEC 11801:2002 Information technology Generic cabling for customer premises
    EN 60352-6:1997 Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance
    EN 61076-1:2006 Connectors for electronic equipment - Product requirements - Part 1: Generic specification
    IEC 60068-2-38:2009 Environmental testing - Part 2-38: Tests - Test Z/AD: Composite temperature/humidity cyclic test
    EN 60352-5:2012/AC:2014 SOLDERLESS CONNECTIONS - PART 5: PRESS-IN CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE (IEC 60352-5:2012)
    ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
    IEC 61156-2:2010 Multicore and symmetrical pair/quad cables for digital communications - Part 2: Symmetrical pair/quad cables with transmission characteristics up to 100 MHz - Horizontal floor wiring - Sectional specification
    IEC 60603-7-3:2010 Connectors for electronic equipment - Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 100 MHz
    EN 60068-2-38:2009 Environmental testing - Part 2-38: Tests - Test Z/AD: Composite temperature/humidity cyclic test
    IEC 60352-5:2012 Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance
    IEC 60512-1-100:2012 Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications
    IEC 60603-7-41:2010 Connectors for electronic equipment - Part 7-41: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 500 MHz
    EN 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    IEC 61156-1:2007+AMD1:2009 CSV Multicore and symmetrical pair/quad cables for digital communications - Part 1: Generic specification
    IEC 61169-16:2006 Radio-frequency connectors - Part 16: Sectional specification - RF coaxial connectors with inner diameter of outer conductor 7 mm (0,276 in) with screw coupling - Characteristics impedance 50 ohms (75 ohms) (type N)
    IEC 61156-7:2003+AMD1:2012 CSV Multicore and symmetrical pair/quad cables for digital communications - Part 7: Symmetrical pair cables with transmissioncharacteristics up to 1 200 MHz - Sectional specification fordigital and analog communication cables
    IEC 61156-6:2010+AMD1:2012 CSV Multicore and symmetrical pair/quad cables for digital communications - Part 6: Symmetrical pair/quad cables withtransmission characteristics up to 1 000 MHz - Work area wiring -Sectional specification
    IEC 60352-2:2006+AMD1:2013 CSV Solderless connections - Part 2: Crimped connections - Generalrequirements, test methods and practical guidance
    EN 60352-4:1994/A1:2000 SOLDERLESS CONNECTIONS - PART 4: SOLDERLESS NON-ACCESSIBLE INSULATION DISPLACEMENT CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE
    IEC 61156-5:2009+AMD1:2012 CSV Multicore and symmetrical pair/quad cables for digital communications - Part 5: Symmetrical pair/quad cables withtransmission characteristics up to 1 000 MHz - Horizontal floorwiring - Sectional specification
    IEC 61156-4:2009 Multicore and symmetrical pair/quad cables for digital communications - Part 4: Riser cables - Sectional specification
    IEC 60603-7-5:2010 Connectors for electronic equipment - Part 7-5: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz
    IEC 61156-3:2008 Multicore and symmetrical pair/quad cables for digital communications - Part 3: Work area cable - Sectional specification
    EN 60352-7:2002 Solderless connections - Part 7: Spring clamp connections - General requirements, test methods and practical guidance
    IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
    IEC 60603-7-7:2010 Connectors for electronic equipment - Part 7-7: Detail specification for 8-way, shielded, free and fixed connectors for data transmission with frequencies up to 600 MHz
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    EN 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
    IEC 60050-581:2008 International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
    IEC 60603-7-51:2010 Connectors for electronic equipment - Part 7-51: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 500 MHz
    IEC 60352-7:2002 Solderless connections - Part 7: Spring clamp connections - General requirements, test methods and practical guidance
    IEC 60603-7-4:2010 Connectors for electronic equipment - Part 7-4: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective