Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN ISO 11118:2015&LC:2015-12

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    GAS CYLINDERS - NON-REFILLABLE METALLIC GAS CYLINDERS - SPECIFICATION AND TEST METHODS (ISO 11118:2015)

    Available format(s):  Hardcopy, PDF

    Superseded date:  13-05-2020

    Language(s):  English

    Published date:  01-01-2015

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    European foreword
    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols
    5 Materials
    6 Inspection and testing
    7 Design
    8 Construction and workmanship
    9 Type approval procedure
    10 Batch tests
    11 Tests on every cylinder
    12 Markings
    13 Test reports and certificate of compliance
    Annex A (normative) - Non-refillable sealing
            devices - Specifications and prototype
            testing
    Annex B (informative) - Type approval certificate
    Annex C (informative) - Certificate of compliance
    Annex D (informative) - Yield point elongation (YPE)
    Bibliography

    Abstract - (Show below) - (Hide below)

    This International Standard specifies minimum requirements for the material, design, inspections, construction and workmanship, manufacturing processes, and tests at manufacture of non-refillable metallic gas cylinders of welded, brazed, or seamless construction for compressed and liquefied gases including the requirements for their non-refillable sealing devices and their methods of testing

    General Product Information - (Show below) - (Hide below)

    Committee TC 58
    Development Note Supersedes I.S. EN ISO 13340 & I.S. EN 12205. (12/2015)
    Document Type Test Method
    Product Note The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document. CORRECTED VERSION IS AVAILABLE NOW FOR THIS STANDARD
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 6506-3:2014 Metallic materials Brinell hardness test Part 3: Calibration of reference blocks
    ISO 6506-1:2014 Metallic materials Brinell hardness test Part 1: Test method
    ISO 11114-1:2012 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials
    ISO 9809-4:2014 Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 4: Stainless steel cylinders with an Rm value of less than 1 100 MPa
    ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
    ISO 20703:2006 Gas cylinders Refillable welded aluminium-alloy cylinders Design, construction and testing
    ISO 9329-1:1989 Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 1: Unalloyed steels with specified room temperature properties
    ISO 9606-1:2012 Qualification testing of welders — Fusion welding — Part 1: Steels
    ISO 11114-3:2010 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 3: Autogenous ignition test for non-metallic materials in oxygen atmosphere
    ISO 4706:2008 Gas cylinders — Refillable welded steel cylinders — Test pressure 60 bar and below
    ISO 7866:2012 Gas cylinders — Refillable seamless aluminium alloy gas cylinders — Design, construction and testing
    ISO 10297:2014 Gas cylinders — Cylinder valves — Specification and type testing
    ISO 15614-1:2017 Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
    ISO 11114-2:2013 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials
    ISO 3651-2:1998 Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid
    ISO 13585:2012 Brazing Qualification test of brazers and brazing operators
    ISO 17639:2003 Destructive tests on welds in metallic materials Macroscopic and microscopic examination of welds
    ISO 10156:2017 Gas cylinders — Gases and gas mixtures — Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets
    ISO 6506-2:2017 Metallic materials Brinell hardness test Part 2: Verification and calibration of testing machines
    EN 13134:2000 Brazing - Procedure approval
    ISO 15613:2004 Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test
    ISO 9809-1:2010 Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective