AWS C3.7 : 1999

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

SPECIFICATION FOR ALUMINUM BRAZING

Available format(s):

Superseded date: 23-07-2013

Language(s):

Published date: 12-01-2013

Publisher: American Welding Society

Table of Contents - (Show below) - (Hide below)

Personnel
Foreword
1. Scope
2. Applicable Documents
3. Classification of Brazed Joints
     3.1 Method of Classification
     3.2 Class A Joints
     3.3 Class B Joints
     3.4 Class C Joints
     3.5 No Class Specified
4. Process Requirements
     4.1 Process Description
     4.2 General Furnace Requirements
     4.3 Temperature Requirements
     4.4 Furnace or Oven Operational Requirements
     4.5 Fixtures
     4.6 Aluminum Brazing Materials
     4.7 Product Brazing Requirements
     4.8 Brazing Procedure Qualification
     4.9 Safety and Health
5. Quality Assurance Provisions
     5.1 Responsibility for Inspection
     5.2 Responsibility for Compliance
     5.3 Sequence of Inspection and Manufacturing Operations
     5.4 Required Nondestructive Examination of Brazed Joints
     5.5 Acceptance Criteria
     5.6 Process Completion
6. Definitions
Annex A - Guidelines for Preparation of Technical
          Inquiries for AWS Technical Committees
A1. Introduction
A2. Procedure
A3. Interpretation of Provisions of the Standard
A4. Publication of Interpretations
A5. Telephone Inquiries
A6. The AWS Technical Committee
AWS Brazing and Soldering Documents

Abstract - (Show below) - (Hide below)

Establishes minimum fabrication and quality requirements for the brazing of aluminum and aluminum alloys. Standardizes brazing process requirements and control braze joint quality for all applications where braze joints of assured quality are necessary.

General Product Information - (Show below) - (Hide below)

Development Note	Supersedes MIL B 007883. (06/2004)
Document Type	Standard
ISBN
Pages
Published
Publisher	American Welding Society
Status	Superseded
Superseded By	AWS C3.7M/C3.7 : 2005 AWS C3.7M/C3.7 : 2011
Supersedes	MIL-B-007883 Revision C:1968 MIL-B-7883 Revision B:1968

Standards Referenced By This Book - (Show below) - (Hide below)

MS27225 Revision C:2007	Nipple Assembly 45 Degrees, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines
AWS BRH:2007	BRAZING HANDBOOK
SAE AS 12500 : 2018	CORROSION PREVENTION AND DETERIORATION CONTROL IN ELECTRONIC COMPONENTS AND ASSEMBLIES
MIL-STD-2088 Revision B:2007	BOMB RACK UNIT (BRU), SINGLE STORE, AIRCRAFT
IPC A 630 CHINESE : -	ACCEPTABILITY STANDARD FOR MANUFACTURE, INSPECTION AND TESTING OF ELECTRONIC ENCLOSURES
MIL-HDBK-510 Revision A:2014	AEROSPACE FUELS CERTIFICATION
MIL-G-18997 Revision E:1991	GAUGE, PRESSURE, DIAL INDICATING
MIL-HDBK-115 Revision C:2016	U.S. ARMY REVERSE ENGINEERING HANDBOOK (GUIDELINES AND PROCEDURES)
MIL-STD-186 Revision F:2002	PROTECTIVE FINISHING SYSTEMS FOR ROCKETS, GUIDED MISSILES, SUPPORT EQUIPMENT AND RELATED MATERIALS
MIL-HDBK-510-1 Revision A:2010	AEROSPACE FUELS CERTIFICATION
NASA STD 5005(INT) : 2007	THE DESIGN AND FABRICATION OF GROUND SUPPORT EQUIPMENT
IPC A 630 : 0	ACCEPTABILITY STANDARD FOR MANUFACTURE, INSPECTION AND TESTING OF ELECTRONIC ENCLOSURES
JSSG-2010-12 Base Document:1998	Crew Systems Deployable Aerodynamic Decelerator (DAD) Systems Handbook
AWS WHC1.10 : 0	WELDING SCIENCE AND TECHNOLOGY, WELDING HANDBOOK, 9TH ED., VOL 1 - CHAPTER 10: MONITORING AND CONTROL OF WELDING AND JOINING PROCESSES
MS27223 Revision C:2007	Nipple Assembly 90 Degrees, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines 1/4 Inch through 2 Inch Tube Sizes
MIL-DTL-83413-8 Revision E:2015	CONNECTORS AND ASSEMBLIES, ELECTRICAL, AIRCRAFT GROUNDING: TYPE 4 JUMPER CABLE ASSEMBLY, LEAD, ELECTRICAL

Standards Referencing This Book - (Show below) - (Hide below)

ASTM E 230 : 2003	Standard Specification and Temperature-Electromotive Force (EMF) Tables for Standardized Thermocouples
AWS A5.31 : 1992	SPECIFICATION FOR FLUXES FOR BRAZING AND BRAZE WELDING
AWS A2.4 : 2012	STANDARD SYMBOLS FOR WELDING, BRAZING, AND NONDESTRUCTIVE EXAMINATION
AWS C3.3 : 2008	RECOMMENDED PRACTICES FOR THE DESIGN, MANUFACTURE, AND EXAMINATION OF CRITICAL BRAZED COMPONENTS
SAE AMS 2750 : 2012	PYROMETRY
AWS A3.0 : 0	STANDARD WELDING TERMS AND DEFINITIONS - INCLUDING TERMS FOR ADHESIVE BONDING, BRAZING, SOLDERING, THERMAL CUTTING, AND THERMAL SPRAYING
AWS BRH:2007	BRAZING HANDBOOK
AWS B2.2 : 1991	STANDARD FOR BRAZING PROCEDURE AND PERFORMANCE QUALIFICATION
AWS C3.8 : 90(R1998)	RECOMMENDED PRACTICES FOR ULTRASONIC INSPECTION OF BRAZED JOINTS
AWS A5.8 : 1992	FILLER METALS FOR BRAZING AND BRAZE WELDING, SPECIFICATION FOR

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart