Skip to content
Please enter a keyword to search

  • AWS C4.6M : 2006

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    THERMAL CUTTING - CLASSIFICATION OF THERMAL CUTS - GEOMETRIC PRODUCT SPECIFICATION AND QUALITY TOLERANCES

    Available format(s): 

    Superseded date:  28-04-2023

    Language(s): 

    Published date:  01-01-2012

    Publisher:  American Welding Society

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Personnel (Reaffirmation)
    Personnel (Original)
    Foreword
    List of Tables
    List of Figures
    1. Scope
    2. Normative references
    3. Terms and definitions
    4. Symbols
    5. Form and location tolerances
    6. Determination of the quality of cut surfaces
    7. Quality of the cut surface
    8. Dimensional tolerances
    9. Designation
    10. Information in technical documentation
    Annex A (informative) - Achievable cutting qualities for
             different cutting processes
    Annex B (informative) - Principles of process
    Bibliography
    National Informative Annexes
    Annex C (Informative) - Criteria for Describing Oxygen-Cut
            Surfaces
    Annex D (Informative) - Bibliography
    Annex E (Informative) - Guidelines for the Preparation of
            Technical Inquiries
    List of AWS Documents on Oxyfuel Gas Welding and Cutting

    Abstract - (Show below) - (Hide below)

    Pertains to materials suitable for oxyfuel flame cutting, plasma cutting and laser cutting.

    General Product Information - (Show below) - (Hide below)

    Committee C4
    Document Type Standard
    Product Note Reconfirmed 2006
    Publisher American Welding Society
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    CGA E 5 : 2017 OXY-FUEL TORCH STANDARD
    ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
    ISO 2553:2013 Welding and allied processes Symbolic representation on drawings Welded joints
    AWS C4.1 SET : 1977 CRITERIA FOR DESCRIBING OXYGEN-CUT SURFACES, AND OXYGEN CUTTING SURFACE ROUGHNESS GAUGE
    ISO 4287:1997 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
    CGA E 1 : 2016 STANDARD FOR RUBBER WELDING HOSE AND HOSE CONNECTIONS FOR GAS WELDING, CUTTING, AND ALLIED PROCESSES
    AWS C4.2/C4.2M : 2009 RECOMMENDED PRACTICES FOR OXYFUEL GAS CUTTING TORCH OPERATION
    ISO 3821:2008 Gas welding equipment Rubber hoses for welding, cutting and allied processes
    ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
    RMA RP 1 : 1990 MINIMUM REQUIREMENTS FOR NON-REINFORCED BLACK EPDM RUBBER SHEETS FOR USE IN ROOFING APPLICATIONS
    ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
    AWS C4.5M:2012 UNIFORM DESIGNATION SYSTEM FOR OXYFUEL NOZZLES
    AWS C4.4/C4.4M : 2007 RECOMMENDED PRACTICES FOR HEAT SHAPING AND STRAIGHTENING WITH OXYFUEL GAS HEATING TORCHES
    ISO 3274:1996 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments
    CFR 29(PT1910.1000 TO END) : 0 LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR
    NFPA 51 : 2018 DESIGN AND INSTALLATION OF OXYGEN-FUEL GAS SYSTEMS FOR WELDING, CUTTING, AND ALLIED PROCESSES
    ISO 3253:1998 Gas welding equipment Hose connections for equipment for welding, cutting and allied processes
    ANSI Z49.1 : 2012 SAFETY IN WELDING, CUTTING, AND ALLIED PROCESSES
    ISO 5175:1987 Equipment used in gas welding, cutting and allied processes Safety devices for fuel gases and oxygen or compressed air General specifications, requirements and tests
    AWS F4.1 : 2007 SAFE PRACTICES FOR THE PREPARATION OF CONTAINERS AND PIPING FOR WELDING, CUTTING, AND ALLIED PROCESSES
    ISO 17658:2002 Welding — Imperfections in oxyfuel flame cuts, laser beam cuts and plasma cuts — Terminology
    ARPM IP7 : 2016 SPECIFICATIONS FOR RUBBER WELDING HOSE
    AWS C4.3/C4.3M : 2004 RECOMMENDED PRACTICES FOR SAFE AND OXYFUEL GAS HEATING TORCH OPERATION
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective