• BS 2011-2.1N(1985) : 1985

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    ENVIRONMENTAL TESTING - TESTS - TEST N: CHANGE OF TEMPERATURE

    Available format(s):  Hardcopy, PDF

    Superseded date:  15-04-2000

    Language(s):  English

    Published date:  01-01-1985

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National foreword
    Method
    Introduction
    1 Test Na: Rapid change of temperature with
                 prescribed time of transition
    2 Test Nb: Change of temperature with specified rate
                 of change
    3 Test Nc: Rapid change of temperature, two-fluid-bath
                 method
    Figures
    1 Untitled
    2 Untitled
    3 Untitled

    Abstract - (Show below) - (Hide below)

    Describes the basic environmental tests and procedures to determine a change in temperature on a specimen.

    General Product Information - (Show below) - (Hide below)

    Committee GEL/15
    Development Note Implements CENELEC HD 323.2.14 S2
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS QC222000(1996) : 1996 RADIO-FREQUENCY CONNECTORS - RF COAXIAL CONNECTORS WITH INNER DIAMETER OF OUTER CONDUCTOR 6,5 MM (0,256 IN) WITH SCREW COUPLING - CHARACTERISTIC IMPEDANCE 50 OHMS - (TYPE TNC)
    BS 5760-13.3(1993) : 1993 RELIABILITY OF SYSTEMS, EQUIPMENT AND COMPONENTS - GUIDE TO RELIABILITY TEST CONDITIONS FOR CONSUMER EQUIPMENT - CONDITIONS PROVIDING A LOW DEGREE OF SIMULATION FOR EQUIPMENT FOR STATIONARY USE IN PARTIALLY WEATHER PROTECTED LOCATIONS
    BS EN 61049 : 1993 SPECIFICATION FOR CAPACITORS FOR USE IN TUBULAR FLUORESCENT AND OTHER DISCHARGE LAMP CIRCUITS - PERFORMANCE REQUIREMENTS
    BS 6796(1986) : 1986 SPECIFICATION FOR FLICKERMETERS
    BS 5917(1980) : 1980 SPECIFICATION FOR CONFORMAL COATING MATERIAL FOR USE ON PRINTED UK CIRCUIT ASSEMBLIES
    BS EN 119000 : 1997 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION: DRY AND MERCURY WETTED REED CONTACT UNITS
    BS 5760-13.5:1996 RELIABILITY OF SYSTEMS, EQUIPMENT AND COMPONENTS - GUIDE TO RELIABILITY TEST CONDITIONS FOR CONSUMER EQUIPMENT - GROUND MOBILE EQUIPMENT - LOW DEGREE OF SIMULATION
    BS QC410000(1990) : 1990 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - POTENTIOMETERS FOR USE IN ELECTRONIC EQUIPMENT
    BS EN 169000:1993 Harmonized system of quality assessment for electronic components. Generic specification. Quartz crystal controlled oscillators
    BS EN 129000 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION - FIXED RF WOUND INDUCTORS
    BS EN 147000:1995 Harmonized system of quality assessment for electronic components. Generic specification. Sockets for use with electrical relays of assessed quality
    BS QC420000(1992) : 1992 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - VARISTORS FOR USE IN ELECTRONIC EQUIPMENT: GENERIC SPECIFICATION
    BS EN 116303:1996 Harmonized system of quality assessment for electronic components. Blank detail specification: electromechanical all-or-nothing heavy load relays of assessed quality (hermetically sealed, 5A to 25A)
    BS EN 137000 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS: GENERIC SPECIFICATION: FIXED ALUMINIUM ELECTROLYTIC A.C. CAPACITORS WITH NON-SOLID ELECTROLYTE FOR USE WITH MOTORS
    BS QC390000(1992) : 1992 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - FIXED FILM RESISTOR NETWORKS FOR USE IN ELECTRONIC EQUIPMENT - GENERIC SPECIFICATION
    BS QC221400(1997) : 1997 RADIO-FREQUENCY CONNECTORS - RF COAXIAL CONNECTORS WITH INNER DIAMETER OF OUTER CONDUCTOR 3 MM (0,12 IN) WITH SCREW COUPLING - CHARACTERISTIC IMPEDANCE 50 OHMS (TYPE SMC)
    BS EN 117000:1997 Harmonized system of quality assessment for electronic components. Generic specification. Solid state all-or-nothing relays. Generic data and methods of test
    BS QC 160000-1:1987 Harmonized system of quality assessment for electronic components. Electrical relays. Generic specification: electromechanical all-or-nothing relays Test and measurement procedures
    BS QC221200(1997) : 1997 RADIO-FREQUENCY CONNECTORS - RF COAXIAL CONNECTORS WITH INNER DIAMETER OF OUTER CONDUCTOR 6,5 MM (0,256 IN) WITH BAYONET LOCK - CHARACTERISTIC IMPEDANCE 50 OHMS (TYPE BNC)
    BS EN 116000-3:1996 Harmonized system of quality assessment for electronic components. Generic specification: electromechanical all-or-nothing relays Test and measurement procedures
    BS EN 120000 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERAL SPECIFICATION: SEMICONDUCTOR OPTOELECTRONIC AND LIQUID CRYSTAL DEVICES
    BS QC222400(1997) : 1997 RADIO-FREQUENCY CONNECTORS - RF COAXIAL CONNECTORS WITH INNER DIAMETER OF OUTER CONDUCTOR 5,6 MM (0,22 IN) - CHARACTERISTIC IMPEDANCE 75 OHMS (TYPE 1,6/5,6) - CHARACTERISTIC IMPEDANCE 50 OHMS (TYPE 1,8/5,6) WITH SIMILAR MATING DIMENSIONS
    BS 9400(1970) : 1970 AMD 7224 SPECIFICATION FOR INTEGRATED ELECTRONIC CIRCUITS AND MICRO ASSEMBLIES OF ASSESSED QUALITY (QUALIFICATION APPROVAL PROCEDURES): GENERIC DATA AND METHODS OF TEST
    BS CECC41400(1980) : 1980 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS: SECTIONAL SPECIFICATION: ROTARY PRECISION POTENTIOMETERS
    BS AU217-2(1989) : 1989 MAXIMUM ROAD SPEED LIMITERS FOR MOTOR VEHICLES - SPECIFICATION FOR SYSTEM AND COMPONENT REQUIREMENTS
    BS 9610:1982 Specification for quartz crystal units of assessed quality: generic data and methods of test
    BS 9500:1990 SPECIFICATION FOR SOCKETS OF ASSESSED QUALITY FOR PLUG-IN ELECTRONIC COMPONENTS: GENERIC DATA AND METHODS OF TEST
    BS 9600:1983 Specification for piezoelectric crystal filters of assessed quality: generic data and methods of test
    BS 4584-103.3:1992 METAL-CLAD BASE MATERIALS FOR PRINTED WIRING BOARDS - SPECIAL MATERIALS USED IN CONNECTION WITH PRINTED CIRCUITS - SPECIFICATION FOR PERMANENT POLYMER COATING MATERIALS (SOLDER RESIST) FOR USE IN THE FABRICATION OF PRINTED BOARDS
    BS 5760-13.4:1993 RELIABILITY OF SYSTEMS, EQUIPMENT AND COMPONENTS - GUIDE TO RELIABILITY TEST CONDITIONS FOR CONSUMER EQUIPMENT - CONDITIONS PROVIDING A LOW DEGREE OF SIMULATION FOR EQUIPMENT FOR PORTABLE AND NON-STATIONARY USE
    BS QC420100(1992) : 1992 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRIC COMPONENTS - VARISTORS FOR USE IN ELECTRONIC EQUIPMENT - SECTIONAL SPECIFICATION FOR SURGE SUPPRESSION VARISTORS
    BS 9940-0(1983) : 1983 HARMONIZED SYSTEM OF QUALITY ASSESSMENT OF ELECTRONIC COMPONENTS - FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - GENERIC SPECIFICATION
    BS QC760000(1990) : 1990 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - FILM AND HYBRID FILM INTEGRATED CIRCUITS - GENERIC SPECIFICATION
    BS EN 134000 : 1995 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION: VARIABLE CAPACITORS - (QUALIFICATION APPROVAL AND CAPABILITY APPROVAL)
    BS 7822-3(1995) : 1995 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - USE OF COATINGS TO ACHIEVE INSULATION COORDINATION OF PRINTED BOARD ASSEMBLIES
    BS QC221300(1997) : 1997 RADIO-FREQUENCY CONNECTORS - RF COAXIAL CONNECTORS WITH INNER DIAMETER OF OUTER CONDUCTOR 3 MM (0,12 IN) WITH SNAP-ON COUPLING - CHARACTERISTIC IMPEDANCE 50 OHMS (TYPE SMB)
    BS CECC 16000-1:1992 Harmonized system of quality assessment for electronic components. Generic specification: electromechanical all-or-nothing relays General
    BS EN 186000-1 : 1994 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION - CONNECTOR SETS FOR OPTICAL FIBRES AND CABLES - PART 1: REQUIREMENTS, TEST METHODS AND QUALIFICATION APPROVAL PROCEDURES
    BS 9930-0(1983) : AMD 5955 SPECIFICATION FOR HARMONIZED SYSTEM OF QUALITY ASSESSMENT OF ELECTRONIC COMPONENTS - FIXED CAPACITORS FOR USE IN ELECTRONIC COMPONENTS - GENERIC SPECIFICATION
    BS QC 400000:1990 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT: GENERIC SPECIFICATION

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
    IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective