Skip to content
Please enter a keyword to search

  • BS 5350-A2:1990

    Current The latest, up-to-date edition.

    Methods of test for adhesives. Adherends Guide to the selection of adherend materials

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  28-02-1990

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    0 Introduction
    1 Scope
    2 Principles of choice
    3 Adherend materials
    4 Pretreatment
    Appendix
    A Adherend materials for which it is impossible to give
       a precise description
    Tables
    1 List of adherend materials obtainable to British
       Standards
    2 Adherend materials not available to British Standards
    Figures
    1 Straight grain test pieces
    2 Grain inclination across face at maximum permissible
       angle
    3 Inclination of grain to the face

    Abstract - (Show below) - (Hide below)

    Lists British Standards that give specifications for commonly used adherend materials and gives guidance on properties to be controlled in materials for which there are no British Standards.

    Scope - (Show below) - (Hide below)

    This Part of BS 5350 gives information on the availability and selection of materials commonly used as adherends where the requirements are for the following:

    1. general performance tests on adhesives;
    2. specific tests of adhesives for quality control or specification purposes and for the selection of adhesives.

    NOTE. The titles of the publications referred to in this Part of BS 5350 are listed on pages 9 to 11.

    General Product Information - (Show below) - (Hide below)

    Committee PRI/52
    Development Note Supersedes 87/54479 DC. (08/2005) Reviewed and confirmed by BSI, January 2011. (12/2010)
    Document Type Standard
    Publisher British Standards Institution
    Status Current

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 5350-C6:1990 Methods of test for adhesives. Adhesively bonded joints: mechanical tests Determination of bond strength in direct tension in sandwich panels
    BS 5350-C5:2002 Methods of test for adhesives Determination of bond strength in longitudinal shear for rigid adherends
    BS 5350-C5:1990 Methods of test for adhesives. Adhesively bonded joints: mechanical tests Determination of bond strength in longitudinal shear

    Standards Referencing This Book - (Show below) - (Hide below)

    BS 4921:1988 Specification for sherardized coatings on iron or steel
    BS 3650:1976 Specification for oil-extended styrene-butadiene rubbers (SRB). Non-pigmented, emulsion polymerized, general purpose types (1700 series)
    BS 2F 116:1975 Specification for mercerized cotton parachute fabric
    BS 2569(1955) : LATEST SPRAYED METAL COATINGS
    BS L 157:1978 Specification for sheet and strip of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8)
    BS 4021:1971 Specification for flexible polyurethane foam sheeting for use in laminates
    BS 3073:1977 Specification for nickel and nickel alloys: strip
    BS 3290:1960 Specification for toughened polystyrene extruded sheet
    BS 849:1939 Code of practice for plain sheet zinc roofing
    BS 3F 57:1975 Specification for scoured cotton fabric for inflatable equipments
    BS 6431-4.1:1986 Ceramic floor and wall tiles. Extruded ceramic tiles with a water absorption of 6% < E ≤ 10%. Group AIIb Specification for general products
    BS 2TA 7:1973 Specification for bar and section for machining of commercially pure titanium (tensile strength 540-740 N/mm2)
    BS 1763:1975 Specification for thin PVC sheeting (calendered, flexible, unsupported)
    BS 2F 123:1984 Specification for woven nylon narrow fabrics for aerospace purposes (nominally 235 dtex yarns)
    BS V 38:1967 Specification for Sitka spruce as rough timber
    BS 2875:1969 Specification for copper and copper alloys. Plate
    BS 2F 52:1959 Flax reinforcement webbing for aeronautical purposes
    BS 6561:1985 Specification for zinc alloy sheet and strip for building
    BS 690-5:1975 Asbestos-cement slates and sheets Lining sheets and panels
    BS F 127:1983 Specification for nylon fabrics suitable for coating with natural or synthetic elastomers
    BS 6431-7:1986 Ceramic floor and wall tiles Specification for dust-pressed ceramic tiles with a water absorption of 3% < E ≤ 6%. Group BIIa
    BS L 159:1978 Specification for close toleranced sheet and strip of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8)
    BS 2F 119:1982 Specification for 145 g/m2 to 210 g/m2 nylon fabrics
    BS 2871-1:1971 Specification for copper and copper alloys. Tubes Copper tubes for water, gas and sanitation
    BS L 165:1978 Specification for sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8)
    BS 5F 59:2002 Braided linen (flax) cord for aerospace purposes
    BS 6431-4.2:1986 Ceramic floor and wall tiles. Extruded ceramic tiles with a water absorption of 6% < E ≤ 10%. Group AIIb Specification for specific products (terre cuite, cotto, baldosin catalan)
    BS 6566-6:1985 Plywood Specification for limits of defects for the classification of plywood by appearance
    BS 2F 115:1975 Specification for 50 g cotton fabric
    BS 2F 111:1973 Specification for flax harness webbing
    BS L 164:1978 Specification for sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated and aged at room temperature) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8)
    BS 690-2:1981 Asbestos-cement slates and sheets Specification for asbestos-cement and cellulose-asbestos-cement flat sheets
    BS 6431-8:1986 Ceramic floor and wall tiles Specification for dust-pressed ceramic tiles with a water absorption of 6% < E ≤ 10%. Group BIIb
    BS 6431-3.2:1986 Ceramic floor and wall tiles. Extruded ceramic tiles with a water absorption of 3% < E ≤ 6%. Group AIIa Specification for specific products (terre cuite, cotto, baldosin catalan)
    BS 3261:1960 Flexible PVC flooring
    BS 6431-3.1:1986 Ceramic floor and wall tiles. Extruded ceramic tiles with a water absorption of 3% < E ≤ 6%. Group AIIa Specification for general products
    BS 3472:1974 Specification for styrene-butadiene rubber (SBR) - non-pigmented, emulsion polymerized, general purpose types (1500 series)
    BS L 158:1978 Specification for close toleranced sheet and strip of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and aged at room temperature) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8)
    BS 2F 122:1978 Specification for two ply cotton fabric for liferaft packs
    BS 2TA 1:1974 Specification for sheet and strip of commercially pure titanium (tensile strength 290-420 MPa)
    TAPPI T 459 : 2013 SURFACE STRENGTH OF PAPER (WAX PICK TEST)
    BS 3830:1973 Specification for vitreous enamelled steel building components
    BS 1706:1990 Method for specifying electroplated coatings of zinc and cadmium on iron and steel
    BS 5669:1979 Specification for wood chipboard and methods of test for particle board
    BS 3F 118:1980 Specification for 50 g/m2 nylon parachute fabric
    BS 2TA 2:1973 Specification for sheet and strip of commercially pure titanium (tensile strength 390-540 N/mm2)
    BS 3869:1965 Specification for rigid expanded polyvinyl chloride for thermal insulation purposes and building applications
    BS 8F 1:1975 Specification for 140 g linen fabric and serrated edge strip
    BS 6687:1986 Specification for electrolytically zinc coated steel flat rolled products
    BS 690-4:1974 Asbestos-cement slates and sheets Slates
    BS 3837:1977 Specification for expanded polystyrene boards
    BS 3757:1978 Specification for rigid PVC sheet
    BS 3497:1979 Specification for unimpregnated asbestos cement boards for electrical purposes
    BS 5F 37:1981 Specification for 570 g/m2 and 640 g/m2 cotton fabrics
    BS 4F 49:1984 Specification for cotton webbing for aerospace purposes
    BS 4396:1976 Specification. Raw natural rubber
    BS 2TA 6:1973 Specification for sheet and strip of commercially pure titanium (tensile strength 570-730 N/mm2)
    BS DD 139(1986) : 1986 SPECIFICATION FOR ZINC-ALUMINIUM ALLOY INGOTS AND CASTINGS
    BS 2V 37:1968 Specification for Sitka spruce as finished timber
    BS 4646:1970 Specification for high density polythene sheet for general purposes
    BS 3V 4:1929 Specification for aircraft material. Ash
    BS 2871-2:1972 Specification for copper and copper alloys. Tubes Tubes for general purposes
    BS 6F 47:1983 Specification for cotton tape
    BS F 128:1985 Specification for cotton webbing suitable for aerospace purposes (warp yarn nominally R 310 tex)
    BS 3012:1970 Specification for low and intermediate density polythene sheet for general purposes
    BS 1204-2:1979 Synthetic resin adhesives (phenolic and aminoplastic) for wood Specification for close-contact adhesives
    BS 6431-2:1984 Ceramic floor and wall tiles Specification for extruded ceramic tiles with a low water absorption (E ≤ 3%). Group A1
    BS 3831:1964 Specification for vitreous enamel finishes for domestic and catering appliances
    BS 2F 114:1975 Specification for 80 g cotton madapolam fabric
    BS 5350-A1:1976 Methods of test for adhesives. Adherends Adherend preparation
    BS 3379:2003 Flexible polyurethane cellular materials for loadbearing applications. Specification
    BS L 163:1978 Specification for sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated, cold worked for flattening and aged at room temperature) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8)
    BS 6431-6:1984 Ceramic floor and wall tiles Specification for dust-pressed ceramic tiles with a low water absorption (E ≤ 3%). Group B1
    BS 2749:1974 Specification for linen/cotton union tapes
    BS 4608:1970 Specification for copper for electrical purposes. Rolled sheet, strip and foil
    BS 6431-9:1984 Ceramic floor and wall tiles Specification for dust-pressed ceramic tiles with a water absorption of E > 10%. Group BIII
    BS 3B 11:1933 Specification for aircraft material. Brass bars suitable to be brazed or silver soldered
    BS 4584:1970 Specification for metal clad base materials for printed circuits. Methods of test
    BS 2F 124:1985 Specification for woven nylon narrow fabrics for aerospace purposes (nominally 940 dtex yarns)
    BS F 126:1980 Specification for 35 g/m2 nylon parachute fabric
    BS 1230-1:1985 Gypsum plasterboard Specification for plasterboard excluding materials submitted to secondary operations
    BS L 167:1978 Specification for close toleranced sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8)
    BS 2TA 3:1973 SPECIFICATION FOR BAR AND SECTION FOR MACHINING OF COMMERCIALLY PURE TITANIUM (TENSILE STRENGTH 390-540 N/MM[2])
    BS 2871-3:1972 Specification for copper and copper alloys. Tubes Tubes for heat exchangers
    BS 6F 8:1975 Specification for mercerized 140 g cotton fabric and serrated edge strip
    BS 6431-5:1986 Ceramic floor and wall tiles Specification for extruded ceramic tiles with a water absorption of E > 10%. Group AIII
    BS 1470:1987 Specification for wrought aluminium and aluminium alloys for general engineering purposes: plate, sheet and strip
    BS L 166:1978 Specification for close toleranced sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated and aged at room temperature) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8)
    BS DD74(1981) : 1981 PERFORMANCE REQUIREMENTS AND TEST METHODS FOR NON-STRUCTURAL WOOD ADHESIVES
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective