Skip to content
Please enter a keyword to search

  • BS EN 15714-3:2009

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Industrial valves. Actuators Pneumatic part-turn actuators for industrial valves. Basic requirements

    Available format(s):  Hardcopy, PDF

    Superseded date:  28-10-2022

    Language(s):  English

    Published date:  30-11-2009

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Classification/Designation
    4 Design requirements
    5 Conformity assessment
    6 Marking
    7 Part-turn actuator selection guidelines
    8 Documentation
    Annex A (normative) - Endurance test procedure
    Annex B (informative) - Actuator selection guidelines
    Bibliography

    Abstract - (Show below) - (Hide below)

    Gives basic requirements for pneumatic part-turn valve actuators, both double acting and single acting, used for on-off and modulating control duties.

    General Product Information - (Show below) - (Hide below)

    Committee PSE/18/5
    Development Note Supersedes 07/30166912 DC. (12/2009)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 15714-1:2009 Industrial valves - Actuators - Part 1: Terminology and definitions
    EN ISO 4628-1:2016 PAINTS AND VARNISHES - EVALUATION OF DEGRADATION OF COATINGS - DESIGNATION OF QUANTITY AND SIZE OF DEFECTS, AND OF INTENSITY OF UNIFORM CHANGES IN APPEARANCE - PART 1: GENERAL INTRODUCTION AND DESIGNATION SYSTEM (ISO 4628-1:2016)
    EN ISO 3231:1997 Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide (ISO 3231:1993)
    ISO 12944-5:2007 Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 5: Protective paint systems
    EN 60534-6-2:2001 Industrial-process control valves - Part 6-2: Mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators
    ISO 8573-2:2007 Compressed air Part 2: Test methods for oil aerosol content
    EN ISO 9227:2017 Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2017)
    EN 736-2:2016 Valves - Terminology - Part 2: Definition of components of valves
    EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
    ISO 8573-1:2010 Compressed air Part 1: Contaminants and purity classes
    ISO 8573-3:1999 Compressed air Part 3: Test methods for measurement of humidity
    ASME B1.20.1 : 2013(R2018) PIPE THREADS, GENERAL PURPOSE (INCH)
    ISO 12944-2:2017 Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 2: Classification of environments
    ISO 4628-1:2016 Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 1: General introduction and designation system
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    ISO 5599-1:2001 Pneumatic fluid power — Five-port directional control valves — Part 1: Mounting interface surfaces without electrical connector
    EN 12570:2000 Industrial valves - Method for sizing the operating element
    ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
    IEC 60534-6-2:2000 Industrial-process control valves - Part 6-2: Mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    ISO 5599-2:2001 Pneumatic fluid power — Five-port directional control valves — Part 2: Mounting interface surfaces with optional electrical connector
    ISO 8573-4:2001 Compressed air Part 4: Test methods for solid particle content
    EN ISO 5211:2017 Industrial valves - Part-turn actuator attachments (ISO 5211:2017)
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    EN 736-3:2008 Valves - Terminology - Part 3: Definition of terms
    ISO 5211:2017 Industrial valves — Part-turn actuator attachments
    ISO 3231:1993 Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective