Skip to content
Please enter a keyword to search

  • BS EN 16282-8:2017

    Current The latest, up-to-date edition.

    Equipment for commercial kitchens. Components for ventilation in commercial kitchens Installations for treatment of aerosol. Requirements and testing

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  19-09-2017

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    European foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Designations
    5 Construction and function
    6 Technical safety requirements
    7 Hygienic requirements
    8 Instructions
    9 Markings
    Annex A (normative) - UV-Devices for the treatment
            of aerosol
    Annex B (normative) - Ozone generator for the
            treatment of aerosol
    Annex C (normative) - Water spray device for the
            treatment of aerosol
    Annex D (normative) - Microbiological treatment
            of aerosol
    Annex E (normative) - Photo-Catalytic Oxidation
            device for the treatment of aerosol
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines requirements for the design, construction and operation of installations designed for the treatment of aerosol in kitchens including technical safety, ergonomic and hygienic features.

    Scope - (Show below) - (Hide below)

    This European Standard specifies requirements for the design, construction and operation of installations designed for the treatment of aerosol in kitchens including technical safety, ergonomic and hygienic features. This European Standard is applicable to ventilation systems in commercial kitchens, associated areas and other installations processing foodstuffs intended for commercial use. Kitchens and associated areas are special rooms in which meals are prepared, where tableware and equipment is washed, cleaned, food is stored and food waste areas. This European Standard is applicable to ventilation systems except those used in domestic kitchens. Unless otherwise specified, the requirements of this standard should be checked by way of inspection and/or measurement. NOTE Please note the possible existence of additional or alternative local national regulations concerning installation, inspection, maintenance and operation.

    General Product Information - (Show below) - (Hide below)

    Committee RHE/2
    Development Note Supersedes 14/30303762 DC. (10/2017)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN ISO 4287:1998/A1:2009 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - TERMS, DEFINITIONS AND SURFACE TEXTURE PARAMETERS
    EN ISO 7250-1:2017 Basic human body measurements for technological design - Part 1: Body measurement definitions and landmarks (ISO 7250-1:2017)
    EN 894-3:2000+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators
    ISO 14119:2013 Safety of machinery Interlocking devices associated with guards Principles for design and selection
    ISO 4287:1997 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
    EN 547-2:1996+A1:2008 Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings
    EN 16282-7:2017 Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 7: Installation and use of fixed fire suppression systems
    EN ISO 4288 : 1997 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - RULES AND PROCEDURES FOR THE ASSESSMENT OF SURFACE TEXTURE
    EN 12792:2003 Ventilation for buildings - Symbols, terminology and graphical symbols
    EN 547-1:1996+A1:2008 Safety of machinery - Human body measurements - Part 1: Principles for determining the dimensions required for openings for whole body access into machinery
    EN 1717:2000 Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow
    EN 16282-5:2017 Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 5: Air duct; Design and dimensioning
    EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
    ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
    EN 779:2012 Particulate air filters for general ventilation - Determination of the filtration performance
    EN ISO 13565-2 : 1997 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD; SURFACES HAVING STRATIFIED FUNCTIONAL PROPERTIES - PART 2: HEIGHT CHARACTERIZATION USING THE LINEAR MATERIAL RATIO
    ISO 7250-1:2017 Basic human body measurements for technological design — Part 1: Body measurement definitions and landmarks
    ISO 3274:1996 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments
    EN 547-3:1996+A1:2008 Safety of machinery - Human body measurements - Part 3: Anthropometric data
    ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
    EN ISO 14119:2013 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection (ISO 14119:2013)
    EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
    EN ISO 13565-1 : 1997 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - SURFACES HAVING STRATIFIED FUNCTIONAL PROPERTIES - PART 1: FILTERING AND GENERAL MEASUREMENT CONDITIONS
    EN 12198-1:2000+A1:2008 Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 1: General principles
    EN 61140:2016 Protection against electric shock - Common aspects for installation and equipment
    EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
    EN 16282-1:2017 Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 1: General requirements including calculation method
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    EN 13779:2007 Ventilation for non-residential buildings - Performance requirements for ventilation and room-conditioning systems
    IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
    EN ISO 3274 : 1997 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - NOMINAL CHARACTERISTICS OF CONTACT (STYLUS) INSTRUMENTS
    EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
    EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective