• BS EN 60079-14:2014 (published 2016-04)

    Current The latest, up-to-date edition.

    Explosive atmospheres Electrical installations design, selection and erection

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  30-04-2016

    Publisher:  British Standards Institution

    Add To Cart

    Scope - (Show below) - (Hide below)

    This part of the IEC60079 series contains the specific requirements for the design, selection, erection and initial inspection of electrical installations in, or associated with, explosive atmospheres. Where the equipment is required to meet other environmental conditions, for example, protection against ingress of water and resistance to corrosion, additional protection requirements may be necessary. The requirements of this standard apply only to the use of equipment under standard atmospheric conditions as defined in IEC600790 . For other conditions, additional precautions may be necessary, and the equipment should be certified for these other conditions. For example, most flammable materials and many materials which are normally regarded as non-flammable might burn vigorously under conditions of oxygen enrichment. NOTE1 The standard atmospheric conditions defined in IEC600790 relate to the explosion characteristics of the atmosphere and not the operating range of the equipment i.e. Temperature: 20C to 60C; Pressure: 80kPa (0,8bar) to 110kPa (1,1bar); and air with normal oxygen content, typically 21% v/v. These requirements are in addition to the requirements for installations in non-hazardous areas. NOTE2 For voltages up to 1000V a.c. or 1500V d.c. requirements of this standard are based on installation requirements in the IEC60364 series, but other relevant national requirements can apply. This standard applies to all electrical equipment including fixed, portable, transportable and personal, and installations, permanent or temporary. This standard does not apply to electrical installations in mines susceptible to firedamp; NOTE3 This standard can apply to electrical installations in mines where explosive gas atmospheres other than firedamp can be formed and to electrical installations in the surface installation of mines. inherently explosive situations and dust from explosives or pyrophoric substances (for example explosives manufacturing and processing); rooms used for medical purposes; electrical installations in areas where the hazard is due to flammable mist. NOTE4 Additional guidance on the requirements for hazards due to hybrid mixtures of dust or flyings and flammable gas or vapour is provided in AnnexM. No account is taken in this Standard of the toxic risks that are associated with flammable gases, liquids and dusts in concentrations that are usually very much less than the lower explosive limit. In locations where personnel may be exposed to potentially toxic concentrations of flammable material, appropriate precautions should be taken. Such precautions are outside the scope of this Standard.

    General Product Information - (Show below) - (Hide below)

    Committee EXL/31/3
    Development Note Supersedes BS 4137(1967), BS 5345-1(1989), BS 5345-3(1979), BS 5345-4(1977), BS 5345-5(1983), BS 5345-6(1978), BS 5345-7(1979) and BS 5345-8(1980) Supersedes 00/241830 DC (09/2003) Supersedes 91/25141 DC. (03/2007) Supersedes 05/30138005 DC. (01/2009) Supersedes BS EN 61241-14. (04/2012) Supersedes 12/30269297 DC. (07/2014)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 6121-5(2005) : 2005 MECHANICAL CABLE GLANDS - PART 5: CODE OF PRACTICE FOR SELECTION, INSTALLATION AND INSPECTION OF CABLE GLANDS AND ARMOUR GLANDS
    12/30244369 DC : 0 BS 7889 - ELECTRIC CABLES - THERMOSETTING INSULATED, NON-ARMOURED CABLES WITH A VOLTAGE OF 600/1000 V, FOR FIXED INSTALLATIONS
    14/30295204 DC : 0 BS 7629-1 - ELECTRIC CABLES - SPECIFICATION FOR 300/500 V FIRE RESISTANT SCREENED CABLES HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE FOR FIXED INSTALLATIONS - PART 1: MULTICORE CABLES
    BS 8450(2006) : 2006 CODE OF PRACTICE FOR INSTALLATION OF ELECTRICAL AND ELECTRONIC EQUIPMENT IN SHIPS
    BS 6724(2016) : 2016 ELECTRIC CABLES - THERMOSETTING INSULATED, ARMOURED CABLES OF RATED VOLTAGES OF 600/1000 V AND 1900/3300 V FOR FIXED INSTALLATIONS, HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE - SPECIFICATION
    BS 4553-1(1998) : 1998 SPECIFICATION FOR 600/1000 V SINGLE-PHASE SPLIT CONCENTRIC ELECTRIC CABLES - PART 1: CABLES HAVING PVC INSULATION
    03/303439 DC : DRAFT MAR 2003 BS 7540-3:2004 - GUIDE TO USE FOR CABLES WITH A RATED VOLTAGE NOT EXCEEDING 450/750 V - PART 3: NATIONAL STANDARD CABLES NOT INCLUDED IN HD 21 AND HD 22
    11/30227604 DC : 0 BS 5266-1 - EMERGENCY LIGHTING - PART 1: CODE OF PRACTICE FOR THE EMERGENCY ESCAPE LIGHTING OF PREMISES
    BS 5839-8(1998) : 1998 FIRE DETECTION AND FIRE ALARM SYSTEMS FOR BUILDINGS - PART 8: CODE OF PRACTICE FOR THE DESIGN, INSTALLATION, COMMISSIONING AND MAINTENANCE OF VOICE ALARM SYSTEMS
    BS 6164(2011) : 2011 CODE OF PRACTICE FOR HEALTH AND SAFETY IN TUNNELING IN THE CONSTRUCTION INDUSTRY
    BS 4553-2(1998) : 1998 SPECIFICATION FOR 600/1000 V SINGLE-PHASE SPLIT CONCENTRIC ELECTRIC CABLES - PART 2: CABLES HAVING THERMOSETTING INSULATION
    BS 5266-1(2005) : 2005 EMERGENCY LIGHTING - PART 1: CODE OF PRACTICE FOR THE EMERGENCY LIGHTING OF PREMISES
    BS PAS 5308-1(2009) : 2009 CONTROL AND INSTRUMENTATION CABLES - PART 1: SPECIFICATION FOR POLYETHYLENE INSULATED CABLES
    12/30260278 DC : 0 BS 5839-1 - FIRE DETECTION AND FIRE ALARM SYSTEMS FOR BUILDINGS - PART 1: CODE OF PRACTICE FOR DESIGN, INSTALLATION, COMMISSIONING AND MAINTENANCE
    12/30170835 DC : 0 BS 5410-2 - CODE OF PRACTICE FOR OIL FIRING - PART 2: SPACE HEATING, HOT WATER AND STEAM SUPPLY SERVICES FOR COMMERCIAL AND INDUSTRIAL PREMISES
    BS 5266-1(2016) : 2016 EMERGENCY LIGHTING - PART 1: CODE OF PRACTICE FOR THE EMERGENCY LIGHTING OF PREMISES
    15/30301742 DC : 0 BS 7846 - ELECTRIC CABLES - THERMOSETTING INSULATED, ARMOURED, FIRE-RESISTANT CABLES OF RATED VOLTAGE 600/1000 V FOR FIXED INSTALLATIONS, HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE - REQUIREMENTS AND TEST METHODS
    12/30258581 DC : 0 BS 5908-2 - FIRE AND EXPLOSION PRECAUTIONS AT PREMISES HANDLING FLAMMABLE GASES, LIQUIDS AND DUSTS - PART 2: GUIDE TO APPLICABLE STANDARDS AND REGULATIONS
    09/30202584 DC : DRAFT OCT 2009 BS 6701 - TELECOMMUNICATIONS EQUIPMENT AND TELECOMMUNICATIONS CABLING - SPECIFICATION FOR INSTALLATION, OPERATION AND MAINTENANCE
    BS PAS 5308-2(2009) : 2009 CONTROL AND INSTRUMENTATION CABLES - PART 2: SPECIFICATION FOR PVC INSULATED CABLES
    14/30286897 DC : 0 PD 8010-1 - PIPELINE SYSTEMS - PART 1: STEEL PIPELINES ON LAND - CODE OF PRACTICE
    BS 5839-1:2017 FIRE DETECTION AND FIRE ALARM SYSTEMS FOR BUILDINGS - PART 1: CODE OF PRACTICE FOR DESIGN, INSTALLATION, COMMISSIONING AND MAINTENANCE OF SYSTEMS IN NON-DOMESTIC PREMISES
    17/30351608 DC : 0 BS 5410-2 - CODE OF PRACTICE FOR OIL FIRING - PART 2: INSTALLATIONS PROVIDING SPACE HEATING, HOT WATER AND STEAM SUPPLY SERVICES TO NON-DOMESTIC BUILDINGS
    BS 5839-8(2013) : 2013 FIRE DETECTION AND FIRE ALARM SYSTEMS FOR BUILDINGS - PART 8: CODE OF PRACTICE FOR THE DESIGN, INSTALLATION, COMMISSIONING AND MAINTENANCE OF VOICE ALARM SYSTEMS
    BS 5908-2(2012) : 2012 FIRE AND EXPLOSION PRECAUTIONS AT PREMISES HANDLING FLAMMABLE GASES, LIQUIDS AND DUSTS - PART 2: GUIDE TO APPLICABLE STANDARDS AND REGULATIONS
    BS 5467(2016) : 2016 ELECTRIC CABLES - THERMOSETTING INSULATED, ARMOURED CABLES OF RATED VOLTAGES OF 600/1000 V AND 1900/3300 V FOR FIXED INSTALLATIONS - SPECIFICATION
    BS 6701(2010) : 2010 TELECOMMUNICATIONS EQUIPMENT AND TELECOMMUNICATIONS CABLING - SPECIFICATION FOR INSTALLATION, OPERATION AND MAINTENANCE
    15/30301501 DC : 0 BS 5467 - ELECTRIC CABLES - THERMOSETTING INSULATED, ARMOURED CABLES FOR VOLTAGES OF 600/1000 V AND 1900/3300 V, FOR FIXED INSTALLATIONS - SPECIFICATION
    BS 8573(2012) : 2012 ELECTRIC CABLES - THERMOSETTING INSULATED, NON-ARMOURED CABLES WITH A VOLTAGE OF 600/1000 V, FOR FIXED INSTALLATIONS, AND HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE
    BS 5839-8(2008) : 2008 FIRE DETECTION AND FIRE ALARM SYSTEMS FOR BUILDINGS - PART 8: CODE OF PRACTICE FOR THE DESIGN, INSTALLATION, COMMISSIONING AND MAINTENANCE OF VOICE ALARM SYSTEMS
    BS 5410-2:1978 CODE OF PRACTICE FOR OIL FIRING - INSTALLATIONS OF 44 KW AND ABOVE OUTPUT CAPACITY FOR SPACE HEATING HOT WATER AND STEAM SUPPLY PURPOSES
    BS 7540-3:2005 ELECTRIC CABLES - GUIDE TO USE FOR CABLES WITH A RATED VOLTAGE NOT EXCEEDING 450/750 V - PART 3: NATIONAL STANDARD CABLES NOT INCLUDED IN HD 21 AND HD 22
    16/30331553 DC : 0 BS 5266-1 - EMERGENCY LIGHTING - PART 1: CODE OF PRACTICE FOR THE EMERGENCY LIGHTING OF PREMISES
    11/30218915 DC : DRAFT JAN 2011 BS 6164 - CODE OF PRACTICE FOR HEALTH AND SAFETY IN TUNNELING IN THE CONSTRUCTION INDUSTRY
    BS 5410-2(2013) : 2013 CODE OF PRACTICE FOR OIL FIRING - PART 2: INSTALLATIONS OVER 45 KW OUTPUT CAPACITY FOR SPACE HEATING, HOT WATER AND STEAM SUPPLY SERVICES
    BS 5467(1997) : 1997 ELECTRIC CABLES - THERMOSETTING INSULATED, ARMOURED CABLES FOR VOLTAGES OF 600/1000 V AND 1900/3300 V
    DD CEN/TS 14175-5 : 2006 FUME CUPBOARDS - PART 5: RECOMMENDATIONS FOR INSTALLATION AND MAINTENANCE
    BS 7917(1999) : 1999 ELASTOMER INSULATED FIRE RESISTANT (LIMITED CIRCUIT INTEGRITY) CABLES FOR FIXED WIRING IN SHIPS AND ON MOBILE AND FIXED OFFSHORE UNITS - REQUIREMENTS AND TEST METHODS
    BS 7375(2010) : 2010 DISTRIBUTION OF ELECTRICITY ON CONSTRUCTION AND DEMOLITION SITES - CODE OF PRACTICE
    03/637076 DC : DRAFT NOV 2003 TELECOMMUNICATIONS EQUIPMENT AND TELECOMMUNICATIONS CABLING - SPECIFICATION FOR INSTALLATION, OPERATION AND MAINTENANCE
    BS 4553-3(1998) : 1998 SPECIFICATION FOR 600/1000 V SINGLE-PHASE SPLIT CONCENTRIC ELECTRIC CABLES - PART 3: CABLES HAVING THERMOSETTING INSULATION AND LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE
    01/540647 DC : DRAFT MAY 2001 BS 5839-1 - FIRE DETECTION AND ALARM SYSTEMS FOR BUILDINGS - PART 1 - CODE OF PRACTICE FOR SYSTEM DESIGN, INSTALLATION AND MAINTENANCE
    07/30136498 DC : 0 BS 5839-8 - FIRE DETECTION AND ALARM SYSTEMS FOR BUILDINGS - PART 8: CODE OF PRACTICE FOR THE DESIGN, INSTALLATION, COMMISSIONING AND SERVICING OF VOICE ALARM SYSTEMS
    09/30205684 DC : 0 BS 7375 - CODE OF PRACTICE FOR DISTRIBUTION OF ELECTRICITY ON CONSTRUCTION AND BUILDING SITES
    12/30258718 DC : 0 BS 5839-8 - FIRE DETECTION AND FIRE ALARM SYSTEMS FOR BUILDINGS - PART 8: CODE OF PRACTICE FOR THE DESIGN, INSTALLATION, COMMISSIONING AND MAINTENANCE OF VOICE ALARM SYSTEMS
    09/30199575 DC : 0 BS 7846 - ELECTRIC CABLES - THERMOSETTING INSULATED, ARMOURED, FIRE-RESISTANT CABLES OF RATED VOLTAGE 600/1000 V HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE - SPECIFICATION
    12/30244462 DC : 0 BS 8573 - ELECTRIC CABLES - THERMOSETTING INSULATED, NON-ARMOURED CABLES WITH A VOLTAGE OF 600/1000 V, FOR FIXED INSTALLATIONS, HAVING LOW EMISSIONS OF SMOKE AND CORROSIVE WHEN AFFECTED BY FIRE
    BS 6883(1999) : 1999 ELASTOMER INSULATED CABLES FOR FIXED WIRING IN SHIPS AND ON MOBILE AND FIXED OFFSHORE UNITS - REQUIREMENTS AND TEST METHODS
    BS 7846(2000) : 2000 ELECTRIC CABLES - 600/1000 V ARMOURED FIRE-RESISTANT CABLES HAVING THERMOSETTING INSULATION AND LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE
    05/30124836 DC : DRAFT JULY 2005 BS 5266-1 - EMERGENCY LIGHTING - PART 1: CODE OF PRACTICE FOR THE EMERGENCY LIGHTING OF PREMISES
    BS 6701(2004) : 2004 TELECOMMUNICATIONS EQUIPMENT AND TELECOMMUNICATIONS CABLING - SPECIFICATION FOR INSTALLATION, OPERATION AND MAINTENANCE
    BS 6164(2001) : 2001 CODE OF PRACTICE FOR SAFETY IN TUNNELLING IN THE CONSTRUCTION INDUSTRY
    BS 5839-1:2013 FIRE DETECTION AND FIRE ALARM SYSTEMS FOR BUILDINGS - PART 1: CODE OF PRACTICE FOR DESIGN, INSTALLATION, COMMISSIONING AND MAINTENANCE OF SYSTEMS IN NON-DOMESTIC PREMISES
    BS 5266-1:2011 EMERGENCY LIGHTING - PART 1: CODE OF PRACTICE FOR THE EMERGENCY ESCAPE LIGHTING OF PREMISES
    01/207759 DC : DRAFT NOV 2001 BS 6121-3 - ELECTRIC CABLES - ACCESSORIES - CABLE GLANDS - PART 3: CODE OF PRACTICE FOR SELECTION, INSTALLATION AND INSPECTION OF BABLE GLANDS AND ARMOUR GLANDS
    03/308266 DC : DRAFT JUNE 2003 BS 6121-5 - MECHANICAL CABLE GLANDS - PART 5: CODE OF PRACTICE FOR SELECTION, INSTALLATION AND INSPECTION OF CABLE GLANDS AND ARMOUR GLANDS
    BS PD8010-1(2004) : 2004 CODE OF PRACTICE FOR PIPELINES - PART 1: STEEL PIPELINES ON LAND
    BIP 2081 : 2012 A GUIDE TO EMERGENCY LIGHTING
    BS 7540-2(2005) : 2005 ELECTRIC CABLES - GUIDE TO USE FOR CABLES WITH A RATED VOLTAGE NOT EXCEEDING 450/750 V - PART 2: HARMONIZED CABLE TYPES FROM HD 21 AND HD 22
    15/30301443 DC : 0 BS 6724 - ELECTRIC CABLES - THERMOSETTING INSULATED, ARMOURED CABLES FOR VOLTAGES OF 600/1000 V AND 1 900/3300 V FOR FIXED INSTALLATIONS, HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE - SPECIFICATION
    BS PD8010-1(2015) : 2015 PIPELINE SYSTEMS - PART 1: STEEL PIPELINES ON LAND - CODE OF PRACTICE
    BS 6724(1997) : 1997 ELECTRIC CABLES - THERMOSETTING INSULATED, ARMOURED CABLES FOR VOLTAGES OF 600/1000 V AND 1900/3300 V, HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE
    BS 6701(2016) : 2016 TELECOMMUNICATIONS EQUIPMENT AND TELECOMMUNICATIONS CABLING - SPECIFICATION FOR INSTALLATION, OPERATION AND MAINTENANCE
    BS 5839-1(2002) : 2002 FIRE DETECTION AND FIRE ALARM SYSTEMS FOR BUILDINGS - PART 1: CODE OF PRACTICE FOR SYSTEM DESIGN, INSTALLATION, COMMISSIONING AND MAINTENANCE
    EN 14175-3 : 2003 FUME CUPBOARDS - PART 3: TYPE TEST METHODS
    BS 7629-1(2015) : 2015 ELECTRIC CABLES - SPECIFICATION FOR 300/500 V FIRE RESISTANT, SCREENED, FIXED INSTALLATION CABLES HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE - PART 1: MULTICORE CABLES
    BS EN 14175-3:2003 FUME CUPBOARDS - PART 3: TYPE TEST METHODS
    BS 7629-1:2015+A1:2019 ELECTRIC CABLES - SPECIFICATION FOR 300/500 V FIRE RESISTANT, SCREENED, FIXED INSTALLATION CABLES HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE - PART 1: MULTICORE CABLES
    BS 7671(2008) : 2018 REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - IET WIRING REGULATIONS
    BS 7671(2008) : 2008 REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - IET WIRING REGULATIONS
    BS 7846(2009) : 2009 ELECTRIC CABLES - THERMOSETTING INSULATED, ARMOURED, FIRE-RESISTANT CABLES OF RATED VOLTAGE 600/1000 V, HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE - SPECIFICATION
    BS 7846(2015) : 2015 ELECTRIC CABLES - THERMOSETTING INSULATED, ARMOURED, FIRE-RESISTANT CABLES OF RATED VOLTAGE 600/1000 V FOR FIXED INSTALLATIONS, HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE - SPECIFICATION
    BS 7889(2012) : 2012 ELECTRIC CABLES - THERMOSETTING INSULATED, NON-ARMOURED CABLES WITH A VOLTAGE OF 600/1000 V, FOR FIXED INSTALLATIONS
    BS EN 14175-1 : 2003 FUME CUPBOARDS - PART 1: VOCABULARY
    BS EN 14175-6 : 2006 FUME CUPBOARDS - PART 6: VARIABLE AIR VOLUME FUME CUPBOARDS
    BS EN 14175-2 : 2003 FUME CUPBOARDS - PART 2: SAFETY AND PERFORMANCE REQUIREMENTS
    BS EN 14175-4 : 2004 FUME CUPBOARDS - PART 4: ON-SITE TEST METHODS
    EEMUA 133 : 2011 SPECIFICATION FOR UNDERGROUND ARMOURED CABLE PROTECTED AGAINST SOLVENT PENETRATION AND CORROSIVE ATTACK
    EEMUA 138 : 2010 DESIGN AND INSTALLATION OF ON-LINE ANALYSER SYSTEMS
    BS 7846:2015 ELECTRIC CABLES - THERMOSETTING INSULATED, ARMOURED, FIRE-RESISTANT CABLES OF RATED VOLTAGE 600/1000 V FOR FIXED INSTALLATIONS, HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE - SPECIFICATION
    BS 7846:2000 ELECTRIC CABLES - 600/1000 V ARMOURED FIRE-RESISTANT CABLES HAVING THERMOSETTING INSULATION AND LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE
    BS 7629-1:2015+A1:2019 ELECTRIC CABLES - SPECIFICATION FOR 300/500 V FIRE RESISTANT, SCREENED, FIXED INSTALLATION CABLES HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE - PART 1: MULTICORE CABLES
    BS 5266-1:2005 EMERGENCY LIGHTING - PART 1: CODE OF PRACTICE FOR THE EMERGENCY LIGHTING OF PREMISES
    BS 5839-1(2002) : 2002 FIRE DETECTION AND FIRE ALARM SYSTEMS FOR BUILDINGS - PART 1: CODE OF PRACTICE FOR SYSTEM DESIGN, INSTALLATION, COMMISSIONING AND MAINTENANCE
    BS 7671(2008) : 2018 REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - IET WIRING REGULATIONS
    BS 5266-1:2016 EMERGENCY LIGHTING - PART 1: CODE OF PRACTICE FOR THE EMERGENCY LIGHTING OF PREMISES
    BS 6164:2011 CODE OF PRACTICE FOR HEALTH AND SAFETY IN TUNNELING IN THE CONSTRUCTION INDUSTRY
    CEN/TS 14175-5 : 2006 FUME CUPBOARDS - PART 5: RECOMMENDATIONS FOR INSTALLATION AND MAINTENANCE
    BS 5839-1:2017 Fire detection and fire alarm systems for buildings Code of practice for design, installation, commissioning and maintenance of systems in non-domestic premises
    BS 7846:2009 ELECTRIC CABLES - THERMOSETTING INSULATED, ARMOURED, FIRE-RESISTANT CABLES OF RATED VOLTAGE 600/1000 V, HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE - SPECIFICATION
    BS 5410-2:2013 CODE OF PRACTICE FOR OIL FIRING - PART 2: INSTALLATIONS OVER 45 KW OUTPUT CAPACITY FOR SPACE HEATING, HOT WATER AND STEAM SUPPLY SERVICES
    BS 7629-1:2015 ELECTRIC CABLES - SPECIFICATION FOR 300/500 V FIRE RESISTANT, SCREENED, FIXED INSTALLATION CABLES HAVING LOW EMISSION OF SMOKE AND CORROSIVE GASES WHEN AFFECTED BY FIRE - PART 1: MULTICORE CABLES
    BS 7671(2008) : 2008 REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - IET WIRING REGULATIONS
    BS 6164:2001 CODE OF PRACTICE FOR SAFETY IN TUNNELLING IN THE CONSTRUCTION INDUSTRY
    EI Model code of safe practice Part 15:2015 MODEL CODE OF SAFE PRACTICE - PART 15: AREA CLASSIFICATION FOR INSTALLATIONS HANDLING FLAMMABLE FLUIDS
    EN 14175-1 : 2003 FUME CUPBOARDS - PART 1: VOCABULARY
    EN 14175-2 : 2003 FUME CUPBOARDS - PART 2: SAFETY AND PERFORMANCE REQUIREMENTS
    EI Model Code of Safe Practice Part 16:2017 MODEL CODE OF SAFE PRACTICE - PART 16: GUIDANCE ON TANK CLEANING
    EN 14175-4 : 2004 FUME CUPBOARDS - PART 4: ON-SITE TEST METHODS
    EN 14175-6:2006 Fume cupboards - Part 6: Variable air volume fume cupboards

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
    IEC 60079-1:2014 RLV Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
    EN 60079-26:2015 EXPLOSIVE ATMOSPHERES - PART 26: EQUIPMENT WITH EQUIPMENT PROTECTION LEVEL (EPL) GA (IEC 60079-26:2014)
    IEC 61024-1:1990 Protection of structures against lightning - Part 1: General principles
    EN 60079-29-4 : 2010 EXPLOSIVE ATMOSPHERES - PART 29-4: GAS DETECTORS - PERFORMANCE REQUIREMENTS OF OPEN PATH DETECTORS FOR FLAMMABLE GASES
    EN 60079-1:2014 EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D' (IEC 60079-1:2014)
    EN 60079-10-1:2015 EXPLOSIVE ATMOSPHERES - PART 10-1: CLASSIFICATION OF AREAS - EXPLOSIVE GAS ATMOSPHERES (IEC 60079-10-1:2015 + COR1:2015)
    IEC 60079-30-2:2007 Explosive atmospheres - Part 30-2: Electrical resistance trace heating - Application guide for design, installation and maintenance
    EN 60079-29-1:2016 EXPLOSIVE ATMOSPHERES - PART 29-1: GAS DETECTORS - PERFORMANCE REQUIREMENTS OF DETECTORS FOR FLAMMABLE GASES
    EN 60034-1:2010/corrigendum Oct. 2010 ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
    IEC 60079-19:2010+AMD1:2015 CSV Explosive atmospheres - Part 19: Equipment repair, overhaul and reclamation
    IEC 60364-4-41:2005+AMD1:2017 CSV Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
    EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
    ISO 10807:1994 Pipework Corrugated flexible metallic hose assemblies for the protection of electrical cables in explosive atmospheres
    IEC 60079-17:2013 Explosive atmospheres - Part 17: Electrical installations inspection and maintenance
    EN 60079-15:2010 EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION "N"
    EN 60079-19:2011/A1:2015 EXPLOSIVE ATMOSPHERES - PART 19: EQUIPMENT REPAIR, OVERHAUL AND RECLAMATION (IEC 60079-19:2010)
    EN 60060-1 : 2010 HIGH-VOLTAGE TEST TECHNIQUES - PART 1: GENERAL DEFINITIONS AND TEST REQUIREMENTS
    IEC 61008-1:2010+AMD1:2012+AMD2:2013 CSV Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part1: General rules
    HD 60364-4-41:2017/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-41: PROTECTION FOR SAFETY - PROTECTION AGAINST ELECTRIC SHOCK
    IEC 60079-18:2014 RLV Explosive atmospheres - Part 18: Equipment protection by encapsulation “m”
    IEC 60332-2-2:2004 Tests on electric and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable - Procedure for diffusion flame
    EN 60079-10-2 : 2015 EXPLOSIVE ATMOSPHERES - PART 10-2: CLASSIFICATION OF AREAS - EXPLOSIVE DUST ATMOSPHERES (IEC 60079-10-2:2015)
    IEC 60079-10-1:2015 Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres
    IEC 60079-29-4:2009 Explosive atmospheres - Part 29-4: Gas detectors - Performance requirements of open path detectors for flammable gases
    IEC 61241-11:2005 Electrical apparatus for use in the presence of combustible dust - Part 11: Protection by intrinsic safety 'iD'
    EN 60079-6:2015 Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o"
    EN 60332-1-2:2004/A11:2016 TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 1-2: TEST FOR VERTICAL FLAME PROPAGATION FOR A SINGLE INSULATED WIRE OR CABLE - PROCEDURE FOR 1 KW PRE-MIXED FLAME (IEC 60332-1-2:2004/A1:2015)
    EN 60079-28:2015 EXPLOSIVE ATMOSPHERES - PART 28: PROTECTION OF EQUIPMENT AND TRANSMISSION SYSTEMS USING OPTICAL RADIATION (IEC 60079-28:2015)
    IEC TR 60079-16:1990 Electrical apparatus for explosive gas atmospheres. Part 16: Artificial ventilation for the protection of analyser(s) houses
    IEC 60614-2-5:1992 Specifications for conduits for electrical installations - Part 2: Particular specifications for conduits - Section 5: Flexible conduits
    IEC 60079-5:2015 RLV Explosive atmospheres - Part 5: Equipment protection by powder filling "q"
    IEC 60332-1-2:2004+AMD1:2015 CSV Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for 1 kW pre-mixed flame
    EN 60079-30-1:2017 EXPLOSIVE ATMOSPHERES - PART 30-1: ELECTRICAL RESISTANCE TRACE HEATING - GENERAL AND TESTING REQUIREMENTS (IEC/IEEE 60079-30-1:2015, MODIFIED)
    EN 60079-11:2012 EXPLOSIVE ATMOSPHERES - PART 11: EQUIPMENT PROTECTION BY INTRINSIC SAFETY "I" (IEC 60079-11:2011)
    IEC 60079-11:2011 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
    EN 62305-3:2011 PROTECTION AGAINST LIGHTNING - PART 3: PHYSICAL DAMAGE TO STRUCTURES AND LIFE HAZARD
    IEC TS 60034-25:2014 Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide
    IEC 61241-1:2004 Electrical apparatus for use in the presence of combustible dust - Part 1: Protection by enclosures "tD"
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC TS 60034-17:2006 Rotating electrical machines - Part 17: Cage induction motors when fed from converters - Application guide
    IEC 60755:2017 General safety requirements for residual current operated protective devices
    IEC 60079-29-2:2015 RLV Explosive atmospheres - Part 29-2: Gas detectors - Selection, installation, use and maintenance of detectors for flammable gases and oxygen
    EN 50272-2 : 2001 SAFETY REQUIREMENTS FOR SECONDARY BATTERIES AND BATTERY INSTALLATIONS - PART 2: STATIONARY BATTERIES
    IEC 60079-6:2015 Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o"
    IEC 60079-0:2011 Explosive atmospheres - Part 0: Equipment - General requirements
    IEC 60034-1:2017 Rotating electrical machines - Part 1: Rating and performance
    EN 60243-1:2013 ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013)
    IEC 61241-4:2001 Electrical apparatus for use in the presence of combustible dust - Part 4: Type of protection "pD"
    IEC 60079-31:2013 Explosive atmospheres - Part 31: Equipment dust ignition protection by enclosure "t"
    IEC 60079-30-1:2007 Explosive atmospheres - Part 30-1: Electrical resistance trace heating - General and testing requirements
    EN 61558-2-6:2009 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1100 V - PART 2-6: PARTICULAR REQUIREMENTS AND TESTS FOR SAFETY ISOLATING TRANSFORMERS AND POWER SUPPLY UNITS INCORPORATING SAFETY ISOLATING TRANSFORMERS
    IEC 61285:2015 Industrial-process control - Safety of analyser houses
    IEC 61439-1:2011 Low-voltage switchgear and controlgear assemblies - Part 1: General rules
    EN 60079-17:2014 Explosive atmospheres - Part 17: Electrical installations inspection and maintenance
    IEC 61241-2-1:1994 Electrical apparatus for use in the presence of combustible dust - Part 2: Test methods - Section 1: Methods for determining the minimum ignition temperatures of dust
    CLC/TR 50427 : 2004 ASSESSMENT OF INADVERTENT IGNITION OF FLAMMABLE ATMOSPHERES BY RADIO-FREQUENCY RADIATION - GUIDE
    EN 61010-1:2010 SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE - PART 1: GENERAL REQUIREMENTS (IEC 61010-1:2010)
    IEC 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
    IEC 61010-1:2010+AMD1:2016 CSV Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements
    IEC 62305-3:2010 Protection against lightning - Part 3: Physical damage to structures and life hazard
    EN 60079-13 : 2017 EXPLOSIVE ATMOSPHERES - PART 13: EQUIPMENT PROTECTION BY PRESSURIZED ROOM 'P' AND ARTIFICIALLY VENTILATED ROOM 'V' (IEC 60079-13:2017)
    IEC 60079-15:2010 Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
    IEC 60079-13:2017 Explosive atmospheres - Part 13: Equipment protection by pressurized room "p" and artificially ventilated room "v"
    EN 61285:2015 Industrial-process control - Safety of analyzer houses
    IEC 60079-26:2014 RLV Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga
    CLC/TR 50404 : 2003 ELECTROSTATICS - CODE OF PRACTICE FOR THE AVOIDANCE OF HAZARDS DUE TO STATIC ELECTRICITY
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective