• BS EN 60950-22:2017 (published 2017-08)

    Current The latest, up-to-date edition.

    Information technology equipment. Safety Equipment to be installed outdoors

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  08-08-2017

    Publisher:  British Standards Institution

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1 Equipment covered

    This part of IEC60950 applies to information technology equipment intended to be installed in an outdoor location.

    The requirements for outdoor equipment also apply, where relevant, to outdoor enclosures suitable for direct installation in the field and supplied for housing information technology equipment to be installed in an outdoor location.

    1.2 Additional requirements

    Each installation may have particular requirements. Some examples are given in 4.2. In addition, requirements for protection of the outdoor equipment against the effects of direct lightning strikes are not covered by the standard. For information on this subject, see IEC623051 .

    General Product Information - (Show below) - (Hide below)

    Committee EPL/108
    Development Note Supersedes 03/103069 DC (06/2006) Supersedes 15/30297966 DC. (08/2017)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
    ISO 4892-1:2016 Plastics Methods of exposure to laboratory light sources Part 1: General guidance
    IEC 60364-4-43:2008 Low-voltage electrical installations - Part 4-43: Protection for safety - Protection against overcurrent
    EN ISO 8256 : 2004 PLASTICS - DETERMINATION OF TENSILE-IMPACT STRENGTH
    EN 62368-1:2014/AC:2017-03 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED)
    EN ISO 180:2000/A2:2013 PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013)
    EN ISO 4892-1 : 2016 PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE (ISO 4892-1:2016)
    EN ISO 3231:1997 Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide (ISO 3231:1993)
    IEC 61587-1:2016 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
    IEC 60896-21:2004 Stationary lead-acid batteries - Part 21: Valve regulated types - Methods of test
    IEC 60364-5-53:2001+AMD1:2002+AMD2:2015 CSV Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control
    EN 60950-1:2006/A2:2013 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED)
    IEC 60068-2-11:1981 ENVIRONMENTAL TESTING - TEST KA: SALT MIST
    EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
    ISO 8256:2004 Plastics Determination of tensile-impact strength
    ISO 14993:2001 Corrosion of metals and alloys Accelerated testing involving cyclic exposure to salt mist, "dry" and "wet" conditions
    IEC 62305-1:2010 Protection against lightning - Part 1: General principles
    ISO 4628-3:2016 Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 3: Assessment of degree of rusting
    ISO 21207:2015 Corrosion tests in artificial atmospheres — Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases, neutral salt-spray and drying
    ISO 180:2000 Plastics Determination of Izod impact strength
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 60896-22:2004 Stationary lead-acid batteries - Part 22: Valve regulated types - Requirements
    ISO/TS 18173:2005 Non-destructive testing General terms and definitions
    IEC 61643-11:2011 Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods
    IEC 61969-3:2011 MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - OUTDOOR ENCLOSURES - PART 3: ENVIRONMENTAL REQUIREMENTS, TESTS AND SAFETY ASPECTS
    ISO 4892-4:2013 Plastics Methods of exposure to laboratory light sources Part 4: Open-flame carbon-arc lamps
    IEC 61439-5:2014 Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks
    ISO 4892-2:2013 Plastics Methods of exposure to laboratory light sources Part 2: Xenon-arc lamps
    EN 60068-2-11 : 1999 ENVIRONMENTAL TESTING - TESTS - TEST KA-SALT MIST
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    ISO 178:2010 Plastics Determination of flexural properties
    ASTM D 471 : 2016-02 TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    EN ISO 4892-2:2013 PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 2: XENON-ARC LAMPS (ISO 4892-2:2013)
    IEC 62368-1:2014 Audio/video, information and communication technology equipment - Part 1: Safety requirements
    IEC 62485-2:2010 Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries
    ISO 3231:1993 Paints and varnishes Determination of resistance to humid atmospheres containing sulfur dioxide
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective