• BS EN 61020-1:2009 (published 2013-05)

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Electromechanical switches for use in electrical and electronic equipment Generic specification

    Available format(s):  Hardcopy, PDF

    Superseded date:  08-04-2019

    Language(s):  English

    Published date:  31-05-2013

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    INTRODUCTION
    1 Scope and object
    2 General
    3 Quality assessment procedures
    4 Test and measurement procedures
    Annex A (informative) - Quality assurance procedures
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    Pertains to electromechanical switches intended for use in electrical and electronic appliances.

    General Product Information - (Show below) - (Hide below)

    Committee PEL/23
    Development Note Supersedes BS EN 196000, BS EN 196103, BS EN 196500, BS QC960000(1992) and 06/30147118 DC. (02/2010) Supersedes BS QC960100(1992), BS QC960200(1992), BS QC960201(1992), BS QC960300(1992), BS QC960400(1992) and BS QC960500(1992). (06/2013)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60068-2-43:2003 ENVIRONMENTAL TESTING - PART 2-43: TESTS - TEST KD: HYDROGEN SULPHIDE TEST FOR CONTACTS AND CONNECTIONS
    ISO/IEC 17050-1:2004 Conformity assessment Supplier's declaration of conformity Part 1: General requirements
    IEC 60068-2-68:1994 Environmental testing - Part 2-68: Tests - Test L: Dust and sand
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    EN ISO 1101:2017 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRICAL TOLERANCING - TOLERANCES OF FORM, ORIENTATION, LOCATION AND RUN-OUT (ISO 1101:2017)
    EN 60068-2-42 : 2003 ENVIRONMENTAL TESTING - PART 2-42: TESTS - TEST KC: SULPHUR DIOXIDE TEST FOR CONTACTS AND CONNECTIONS
    IEC 60068-2-58:2015+AMD1:2017 CSV Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD)
    IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
    EN 60065:2014/AC:2017-01 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016)
    IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
    EN 60068-2-20 : 2008 ENVIRONMENTAL TESTING - PART 2-20: TESTS - TEST T: TEST METHODS FOR SOLDERABILITY AND RESISTANCE TO SOLDERING HEAT OF DEVICES WITH LEADS
    EN 60068-2-1:2007 ENVIRONMENTAL TESTING - PART 2-1: TESTS - TEST A: COLD
    IEC 60068-2-49:1983 ENVIRONMENTAL TESTING - GUIDANCE TO TEST KC: SULFUR DIOXIDE TEST FOR CONTACTS AND CONNECTIONS
    EN 60068-2-2:2007 ENVIRONMENTAL TESTING - PART 2-2: TESTS - TEST B: DRY HEAT
    ISO 1101:2017 Geometrical product specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-out
    IEC 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
    IEC 60068-2-13:1983 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST M: LOW AIR PRESSURE
    EN 60068-1:2014 ENVIRONMENTAL TESTING - PART 1: GENERAL AND GUIDANCE (IEC 60068-1:2013)
    ISO/IEC Guide 60:2004 Conformity assessment Code of good practice
    IEC Q 01 : 5.0 IEC QUALITY ASSESSMENT SYSTEM FOR ELECTRONIC COMPONENTS (IECQ SYSTEM) - BASIC RULES
    IEC 60068-2-38:2009 ENVIRONMENTAL TESTING - PART 2-38: TESTS - TEST Z/AD: COMPOSITE TEMPERATURE/HUMIDITY CYCLIC TEST
    IEC 60410:1973 Sampling plans and procedures for inspection by attributes
    EN 60068-2-44 : 1995 ENVIRONMENTAL TESTING - PART 2: TESTS - GUIDANCE ON TEST T: SOLDERING
    EN 60068-2-27:2009 ENVIRONMENTAL TESTING - PART 2-27: TESTS - TEST EA AND GUIDANCE: SHOCK
    EN 20286-1 : 1993 ISO SYSTEM OF LIMITS AND FITS - BASES OF TOLERANCES, DEVIATIONS AND FITS
    EN ISO 9001:2015 QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS (ISO 9001:2015)
    EN 60068-2-38:2009 ENVIRONMENTAL TESTING - PART 2-38: TESTS - TEST Z/AD: COMPOSITE TEMPERATURE/HUMIDITY CYCLIC TEST
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 60068-2-77:1999 Environmental testing - Part 2-77: Tests - Test 77: Body strength and impact shock
    EN 60068-2-17 : 1994 BASIC ENVIRONMENTAL TESTING - TEST Q: SEALING
    IEC 61058-1:2016 Switches for appliances - Part 1: General requirements
    IEC 60068-2-17:1994 Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
    ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
    HD 323.2.46 : 200S1 BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - GUIDANCE TO TEST Kd : HYDROGEN SULPHIDE TEST FOR CONTACTS AND CONNECTIONS
    IEC 60068-2-10:2005 Environmental testing - Part 2-10: Tests - Test J and guidance: Mould growth
    ISO/IEC 17050-2:2004 Conformity assessment Supplier's declaration of conformity Part 2: Supporting documentation
    EN 60068-2-21:2006 ENVIRONMENTAL TESTING - PART 2-21: TESTS - TEST U: ROBUSTNESS OF TERMINATIONS AND INTEGRAL MOUNTING DEVICES
    IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
    IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
    EN 60664-1:2007 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS
    EN 60068-2-68 : 1996 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST L: DUST AND SAND
    IEC 60062:2016 Marking codes for resistors and capacitors
    IEC 60068-2-61:1991 Environmental testing - Part 2-61: Test methods - Test Z/ABDM:Climatic sequence
    EN 60062:2016/AC:2016-12 MARKING CODES FOR RESISTORS AND CAPACITORS (IEC 60062:2016/COR1:2016)
    ISO 9001:2015 Quality management systems - Requirements
    IEC 60068-2-42:2003 ENVIRONMENTAL TESTING - PART 2-42: TESTS - TEST KC: SULPHUR DIOXIDE TEST FOR CONTACTS AND CONNECTIONS
    ISO 129-1:2004 Technical drawings Indication of dimensions and tolerances Part 1: General principles
    EN 60068-2-78:2013 ENVIRONMENTAL TESTING - PART 2-78: TESTS - TEST CAB: DAMP HEAT, STEADY STATE (IEC 60068-2-78:2012)
    EN 60068-2-13 : 1999 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST M: LOW AIR PRESSURE
    IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations
    EN 60068-2-6:2008 ENVIRONMENTAL TESTING - PART 2-6: TESTS - TEST FC: VIBRATION (SINUSOIDAL)
    EN 60068-2-77 : 1999 ENVIRONMENTAL TESTING - PART 2-77: TESTS - TEST 77: BODY STRENGTH AND IMPACT SHOCK (IEC 60068-2-77:1999)
    EN 60068-2-61 : 1993 ENVIRONMENTAL TESTING - TEST METHODS - TEST Z/ABDM: CLIMATIC SEQUENCE
    EN 61058-1:2002/A2:2008 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    EN 60068-2-43 : 2003 ENVIRONMENTAL TESTING - PART 2-43: TESTS - TEST KD: HYDROGEN SULPHIDE TEST FOR CONTACTS AND CONNECTIONS
    EN ISO/IEC 17050-1:2010 CONFORMITY ASSESSMENT - SUPPLIER'S DECLARATION OF CONFORMITY - PART 1: GENERAL REQUIREMENTS
    IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    EN 61190-1-3:2007/A1:2010 ATTACHMENT MATERIALS FOR ELECTRONIC ASSEMBLY - PART 1-3: REQUIREMENTS FOR ELECTRONIC GRADE SOLDER ALLOYS AND FLUXED AND NON-FLUXED SOLID SOLDER FOR ELECTRONIC SOLDERING APPLICATIONS
    EN 60068-2-30:2005 ENVIRONMENTAL TESTING - PART 2-30: TESTS - TEST DB: DAMP HEAT, CYCLIC (12 H + 12 H CYCLE)
    IEC 60068-2-44:1995 ENVIRONMENTAL TESTING - PART 2: TESTS - GUIDANCE ON TEST T: SOLDERING
    EN ISO/IEC 17050-2 : 2004 CONFORMITY ASSESSMENT - SUPPLIER'S DECLARATION OF CONFORMITY - PART 2: SUPPORTING DOCUMENTATION
    IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
    EN 60068-2-45:1992/A1:1993 Environmental testing - Part 2: Tests - Test Xa and guidance: Immersion in cleaning solvents
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    EN 60068-2-14:2009 ENVIRONMENTAL TESTING - PART 2-14: TESTS - TEST N: CHANGE OF TEMPERATURE
    IEC 60050-581:2008 International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
    IEC 61190-1-3:2007+AMD1:2010 CSV Attachment materials for electronic assembly - Part 1-3: Requirements for electronic grade solder alloys and fluxed and non-fluxed solid solders for electronic soldering applications
    IEC 60068-2-46:1982 ENVIRONMENTAL TESTING - GUIDANCE TO TEST Kd: HYDROGEN SULPHIDE TEST FOR CONTACTS AND CONNECTIONS
    EN 60721-3-3 : 95 AMD 2 97 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STATIONARY USE AT WEATHER-PROTECTED LOCATIONS
    IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective