• BS EN 62282-5-1:2012 (published 2013-01)

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Fuel cell technologies Portable fuel cell power systems. Safety

    Available format(s):  Hardcopy, PDF

    Superseded date:  08-09-2018

    Language(s):  English

    Published date:  31-01-2013

    Publisher:  British Standards Institution

    Add To Cart

    Scope - (Show below) - (Hide below)

    IEC 62282-5-1:2012 covers construction, marking and test requirements for portable fuel cell power systems intended to produce electrical power. Applies to a.c. and d.c. type portable fuel cell power systems, with a rated output voltage not exceeding 600 V a.c., or 850 V d.c. for indoor and outdoor use. The major technical changes with respect to the first edition are as follows:
    - referencing an alternative test method; reduction of the limit on flammable atmospheres;
    - consideration of additional effluents and criteria to establish if a system is suitable for indoor or outdoor operation;
    - revision of specific criteria for oxygen detector sensor performance;
    - new test method and new drop heights; addition of a table giving limits on emission of effluents.
    Keywords: fuel cell

    General Product Information - (Show below) - (Hide below)

    Committee GEL/105
    Development Note Supersedes 04/30089617 DC. (07/2007) Supersedes 10/30173705 DC. (01/2013)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61025:2006 Fault tree analysis (FTA)
    IEC 60695-11-20:2015 Fire hazard testing - Part 11-20: Test flames - 500 W flame test method
    IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
    EN 60812 : 2006 ANALYSIS TECHNIQUES FOR SYSTEM RELIABILITY - PROCEDURE FOR FAILURE MODE AND EFFECTS ANALYSIS (FMEA)
    IEC 60079-10:2002 Electrical apparatus for explosive gas atmospheres - Part 10: Classification of hazardous areas
    ISO 15649:2001 Petroleum and natural gas industries Piping
    ISO 7010:2011 Graphical symbols Safety colours and safety signs Registered safety signs
    IEC 61000-6-4:2006+AMD1:2010 CSV ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS
    EN 60068-2-75:2014 ENVIRONMENTAL TESTING - PART 2-75: TESTS - TEST EH: HAMMER TESTS (IEC 60068-2-75:2014)
    EN 61000-6-1:2007 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-1: GENERIC STANDARDS - IMMUNITY FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS
    EN 62040-1:2008/A1:2013 UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: GENERAL AND SAFETY REQUIREMENTS FOR UPS (IEC 62040-1:2008/A1:2013)
    EN 61508-1:2010 FUNCTIONAL SAFETY OF ELECTRICAL/ELECTRONIC/PROGRAMMABLE ELECTRONIC SAFETY-RELATED SYSTEMS - PART 1: GENERAL REQUIREMENTS
    EN 61000-6-3:2007/A1:2011/AC:2012 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010)
    IEC 60050-195:1998 International Electrotechnical Vocabulary (IEV) - Part 195: Earthing and protection against electric shock
    IEC 62282-6-100:2010+AMD1:2012 CSV Fuel cell technologies - Part 6-100: Micro fuel cell power systems - Safety
    EN 60079-29-1:2016 EXPLOSIVE ATMOSPHERES - PART 29-1: GAS DETECTORS - PERFORMANCE REQUIREMENTS OF DETECTORS FOR FLAMMABLE GASES
    IEC 61511-1:2016+AMD1:2017 CSV Functional safety - Safety instrumented systems for the process industry sector - Part 1: Framework, definitions, system, hardware and application programming requirements
    IEC 60812:2006 Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)
    EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
    EN 60079-15:2010 EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION "N"
    IEC 60884-1:2002+AMD1:2006+AMD2:2013 CSV Plugs and socket-outlets for household and similar purposes - Part1: General requirements
    IEC 60934:2000+AMD1:2007+AMD2:2013 CSV Circuit-breakers for equipment (CBE)
    EN 61000-3-3:2013 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-3: LIMITS - LIMITATION OF VOLTAGE CHANGES, VOLTAGE FLUCTUATIONS AND FLICKER IN PUBLIC LOW-VOLTAGE SUPPLY SYSTEMS, FOR EQUIPMENT WITH RATED CURRENT <= 16 A PER PHASE AND NOT SUBJECT TO CONDITIONAL CONNECTION (IEC 61000-3-3:2013)
    EN 61439-1:2011 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1: GENERAL RULES (IEC 61439-1:2011)
    IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
    ISO 16110-1:2007 Hydrogen generators using fuel processing technologies Part 1: Safety
    HD 60364-4-41:2017/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-41: PROTECTION FOR SAFETY - PROTECTION AGAINST ELECTRIC SHOCK
    EN 60950-1:2006/A2:2013 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED)
    IEC 61000-6-1 : 3.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-1: GENERIC STANDARDS - IMMUNITY STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS
    IEC 60216-4-1:2006 Electrical insulating materials - Thermal endurance properties - Part 4-1: Ageing ovens - Single-chamber ovens
    EN ISO 16017-1 : 2000 INDOOR, AMBIENT AND WORKPLACE AIR - SAMPLING AND ANALYSIS OF VOLATILE ORGANIC COMPOUNDS BY SORBENT TUBE/THERMAL DESORPTION/CAPILLARY GAS CHROMATOGRAPHY - PART 1: PUMPED SAMPLING
    EN 62282-2:2012 FUEL CELL TECHNOLOGIES - PART 2: FUEL CELL MODULES (IEC 62282-2:2012)
    IEC 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
    IEC 60079-20-1:2010 Explosive atmospheres - Part 20-1: Material characteristics for gas and vapour classification - Test methods and data
    ISO 16017-1:2000 Indoor, ambient and workplace air Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography Part 1: Pumped sampling
    IEC 62282-2:2012 Fuel cell technologies - Part 2: Fuel cell modules
    IEC 62040-1:2017 EXV UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: SAFETY REQUIREMENTS
    IEC 60695-2-13:2010+AMD1:2014 CSV Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods- Glow-wire ignition temperature (GWIT) test method for materials
    IEC 60050-426:2008 International Electrotechnical Vocabulary (IEV) - Part 426: Equipment for explosive atmospheres
    EN 60695-2-13:2010/A1:2014 FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS (IEC 60695-2-13:2010/A1:2014)
    EN ISO 4080 : 2009 RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES - DETERMINATION OF PERMEABILITY TO GAS (ISO 4080:2009)
    IEC 61000-6-3:2006+AMD1:2010 CSV Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
    IEC 62040-2:2016 Uninterruptible power systems (UPS) - Part 2: Electromagnetic compatibility (EMC) requirements
    EN 61511-3:2017 FUNCTIONAL SAFETY - SAFETY INSTRUMENTED SYSTEMS FOR THE PROCESS INDUSTRY SECTOR - PART 3: GUIDANCE FOR THE DETERMINATION OF THE REQUIRED SAFETY INTEGRITY LEVELS (IEC 61511-3:2016)
    ISO 16111:2008 Transportable gas storage devices Hydrogen absorbed in reversible metal hydride
    IEC 61511-3:2016 Functional safety - Safety instrumented systems for the process industry sector - Part 3: Guidance for the determination of the required safety integrity levels
    EN 61000-6-2:2005/corrigendum:2005 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005)
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    EN 61000-6-4:2007/A1:2011 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS
    EN 61025 : 2007 FAULT TREE ANALYSIS (FTA)
    IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
    EN 61032 : 1998 PROTECTION OF PERSONS AND EQUIPMENT BY ENCLOSURES - PROBES FOR VERIFICATION (IEC 61032:1997)
    EN 60664-1:2007 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS
    IEC 60439-1:1999+AMD1:2004 CSV LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1: TYPE-TESTED AND PARTIALLY TYPE-TESTED ASSEMBLIES
    IEC 60079-0:2011 Explosive atmospheres - Part 0: Equipment - General requirements
    EN 60934:2001/A2:2013 CIRCUIT BREAKERS FOR EQUIPMENT (CBE) (IEC 60934:2000/A2:2013)
    EN 60079-10:2003 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 10: CLASSIFICATION OF HAZARDOUS AREAS
    EN 61000-3-2:2014 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT <= 16 A PER PHASE) (IEC 61000-3-2:2014)
    IEC 60730-2-5:2013+AMD1:2017 CSV Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems
    ISO 15156-1:2015 Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 1: General principles for selection of cracking-resistant materials
    EN 60079-20-1 : 2010 EXPLOSIVE ATMOSPHERES - PART 20-1: MATERIAL CHARACTERISTICS FOR GAS AND VAPOUR CLASSIFICATION - TEST METHODS AND DATA
    ISO 16000-3:2011 Indoor air Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air Active sampling method
    EN 60086-4:2015 (edition 4) Primary batteries - Part 4: Safety of lithium batteries
    EN 62040-2:2006/corrigendum:2006
    IEC 61000-3-3 : 3.0EN+(REDLINE+VERSION) ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-3: LIMITS - LIMITATION OF VOLTAGE CHANGES, VOLTAGE FLUCTUATIONS AND FLICKER IN PUBLIC LOW-VOLTAGE SUPPLY SYSTEMS, FOR EQUIPMENT WITH RATED CURRENT <= 16 A PER PHASE AND NOT SUBJECT TO CONDITIONAL CONNECTION
    IEC 60068-2-75:2014 Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
    EN 61140:2016 PROTECTION AGAINST ELECTRIC SHOCK - COMMON ASPECTS FOR INSTALLATION AND EQUIPMENT (IEC 61140:2016)
    EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
    EN 60730-2-5:2015 AUTOMATIC ELECTRICAL CONTROLS - PART 2-5: PARTICULAR REQUIREMENTS FOR AUTOMATIC ELECTRICAL BURNER CONTROL SYSTEMS (IEC 60730-2-5:2013, MODIFIED)
    IEC 61439-1:2011 Low-voltage switchgear and controlgear assemblies - Part 1: General rules
    IEC 62133 : 2.0EN+(REDLINE+VERSION) SECONDARY CELLS AND BATTERIES CONTAINING ALKALINE OR OTHER NON-ACID ELECTROLYTES - SAFETY REQUIREMENTS FOR PORTABLE SEALED SECONDARY CELLS, AND FOR BATTERIES MADE FROM THEM, FOR USE IN PORTABLE APPLICATIONS
    EN 60216-4-1 : 2006 ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 4-1: AGEING OVENS - SINGLE-CHAMBER OVENS
    IEC 61508-1:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508)
    IEC 60086-4:2014 Primary batteries - Part 4: Safety of lithium batteries
    ISO 7000:2014 Graphical symbols for use on equipment Registered symbols
    ISO 4080:2009 Rubber and plastics hoses and hose assemblies Determination of permeability to gas
    IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
    EN 60695-11-5:2017 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE (IEC 60695-11-5:2016)
    IEC 61032:1997 Protection of persons and equipment by enclosures - Probes for verification
    IEC 60730-2-17:1997+AMD1:2000+AMD2:2007 CSV Automatic electrical controls for household and similar use - Part 2-17: Particular requirements for electrically operated gas valves, including mechanical requirements
    IEC 60695-11-5 : 2.0 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
    IEC 61000-6-2 : 3.0:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    EN ISO 7010 : 2012 AMD 7 2017 GRAPHICAL SYMBOLS - SAFETY COLOURS AND SAFETY SIGNS - REGISTERED SAFETY SIGNS (ISO 7010:2011/AMD 7:2016)
    ISO 16000-6:2011 Indoor air Part 6: Determination of volatile organic compounds in indoor and test chamber air by active sampling on Tenax TA sorbent, thermal desorption and gas chromatography using MS or MS-FID
    IEC 60079-15:2010 Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
    IEC 60990:2016 Methods of measurement of touch current and protective conductor current
    EN 60730-1:2016 AUTOMATIC ELECTRICAL CONTROLS - PART 1: GENERAL REQUIREMENTS (IEC 60730-1:2013, MODIFIED + COR1:2014)
    EN 60695-2-11:2014 FIRE HAZARD TESTING - PART 2-11: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY TEST METHOD FOR END-PRODUCTS (GWEPT) (IEC 60695-2-11:2014)
    EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
    IEC 61000-3-2 : 4.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT <= 16 A PER PHASE)
    IEC 60730-1:2013+AMD1:2015 CSV Automatic electrical controls - Part 1: General requirements
    EN 60990:2016 METHODS OF MEASUREMENT OF TOUCH CURRENT AND PROTECTIVE CONDUCTOR CURRENT (IEC 60990:2016)
    EN 60079-2:2014/AC:2015 EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014)
    EN 62133:2013 SECONDARY CELLS AND BATTERIES CONTAINING ALKALINE OR OTHER NON-ACID ELECTROLYTES - SAFETY REQUIREMENTS FOR PORTABLE SEALED SECONDARY CELLS, AND FOR BATTERIES MADE FROM THEM, FOR USE IN PORTABLE APPLICATIONS (IEC 62133:2012)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective