C22.1-15

Overview Electrical safety in Canada is the responsibility of individual provinces and territories. As an electrical industry professional, you are responsible for understanding the legislation and regulations in your jurisdiction as well as the differences between current and previous provincial codes. Understanding and applying the requirements of the 2015 Canadian Electrical Code helps ensure the safety of your electrical installations and reduces the need for costly reworks that can help your projects stay on schedule. Why You Need To Buy the 2015 Canadian Electrical Code:​ ​ Contains more than 200 updates and revisions, including major changes to sections on renewable energy, hazardous locations and electric heating Includes changes to hazardous area classifications and zone requirements that will affect your installations and potentially save you money Identifies which core changes will affect the Red Seal Exam and related curriculum Details how changes to existing wiring methods and new wiring methods may impact you Added bonus – FREE hardcopyof the Electrical Quick Reference Guide - $25 value

Preface This twenty-third edition of the Canadian Electrical Code, Part I, was approved by the Committee on the Canadian Electrical Code, Part I, and by the Regulatory Authority Committee at their June 2014 meetings in Victoria, British Columbia. This twenty-third edition supersedes the previous editions, published in 2012, 2009, 2006, 2002, 1998, 1994, 1990, 1986, 1982, 1978, 1975, 1972, 1969, 1966, 1962, 1958, 1953, 1947, 1939, 1935, 1930, and 1927. This edition features important revisions to many Sections. Section 4 now contains requirements for high-voltage cable ampacities and clarified Rules for conductor termination temperature. In addition, a new table (Table 39) simplifies residential service and feeder conductor selection. More options are provided for load and voltage drop calculations. Bonding conductor selection has been clarified through the addition of the new Tables 16A and 16B. In addition, Section 12 contains many new and revised requirements for wiring methods, and the conduit fill tables have been expanded. Section 18 has undergone major revisions. Requirements for Class II and Class III locations have been relocated to Appendix J, and requirements for explosive dust atmospheres based on IEC Zone 20, Zone 21, and Zone 22 have been added to Section 18. The requirements are now located as follows: Zones 0, 1, 2, 20, 21, and 22 - Section 18 Classes I, II, and III and associated Divisions - Appendix J Note: References to Class I alone are intended as general references to all classifications of explosive gas atmospheres, Zone 0, Zone 1, and Zone 2. References to Class II alone or to Class III alone are intended as general references to all classifications of explosive dust atmospheres, Zone 20, Zone 21, and Zone 22. Specific references to a Zone of a Class I location are references to that Zone. There are currently no references to Zones or Divisions of Class II or Class III locations in the body of the Rules of this Code (i.e., Sections 0 to 86). Other revisions in this edition include the following: requirements for arc-fault protection have been expanded and clarified; Section 50 has been merged with Section 64; Section 62 has been completely rewritten; and the term \"injury\" has been replaced with \"damage\" throughout the Code. Many of the changes in this edition were developed by cross-functional working groups. Their work is gratefully acknowledged. General arrangement The Code is divided into numbered Sections, each covering some main division of the work. Sections 0 to 16 and 26 are considered general sections, and the other sections supplement or amend the general sections. The Sections are divided into numbered Rules, with captions for easy reference, as follows: Numbering system - With the exception of Section 38, even numbers have been used throughout to identify Sections and Rules. Rule numbers consist of the Section number separated by a hyphen from the 3- or 4-digit figure. The intention in general is that odd numbers may be used for new Rules required by interim revisions. Due to the introduction of some new Rules and the deletion of some existing Rules during the revision of each edition, the Rule numbers for any particular requirement are not always the same in successive editions. Subdivision of Rules - Rules are subdivided in the manner illustrated by Rules 8-204 and 8-206, and the subdivisions are identified as follows: 00-000 | Rule (1) | Subrule (a) | Item (i) | item (A) | item Reference to other Rules, etc. - Where reference is made to two or more Rules (e.g., Rules 10-200 to 10-206), the first and last Rules mentioned are included in the reference. Where reference is made to a Subrule or Item in the same Rule, only the Subrule number and/or Item letter and the word \"Subrule\" or \"Item\" need be mentioned. If the reference is to another Rule or Section, then the Rule number and the word \"Rule\" shall be stated (e.g., \"Rule 10-200(3)\" and not \"Subrule (3) of Rule 10-200\"). The principal changes that have been made between the 2012 edition of the Canadian Electrical Code, Part I, and this new edition published in 2015 are marked in the text of the Code by the symbol delta in the margin. Users of the Code are advised that the change markers in the text are not intended to be all-inclusive and are provided as a convenience only; such markers cannot constitute a comprehensive guide to the reorganization or revision of the Code. Care must therefore be taken not to rely on the change markers to determine the current requirements of the Code. As always, users of the Code must consider the entire Code and any local amendments or interpretations. Scope This Code covers all electrical work and electrical equipment operating or intended to operate at all voltages in electrical installations for buildings, structures, and premises, including factory-built relocatable and non-relocatable structures, and self-propelled marine vessels stationary for periods exceeding five months and connected to a shore supply of electricity continuously or from time to time, with the following exceptions: installations or equipment employed by an electric, communication, or community antenna distribution system utility in the exercise of its function as a utility, as recognized by the regulatory authority having jurisdiction, and located outdoors or in buildings or sections of buildings used for that purpose; equipment and facilities that are used in the operation of an electric railway and are supplied exclusively from circuits that supply the motive power; installations or equipment used for railway signalling and railway communication purposes, and located outdoors or in buildings or sections of buildings used exclusively for such installations; aircraft; and electrical systems in ships that are regulated under Transport Canada. For mines and quarry applications, see also CSA M421. This Code and any standards referenced in it do not make or imply any assurance or guarantee by the authority adopting this Code with respect to life expectancy, durability, or operating performance of equipment and materials so referenced.