• CSA C61400-3 : 2011

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    WIND TURBINES - PART 3: DESIGN REQUIREMENTS FOR OFFSHORE WIND TURBINES

    Available format(s):  Hardcopy, PDF

    Superseded date:  28-02-2016

    Language(s):  English

    Published date:  01-01-2016

    Publisher:  Canadian Standards Association

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Principal elements
    6 External conditions
    7 Structural design
    8 Control and protection system
    9 Mechanical systems
    10 Electrical system
    11 Foundation design
    12 Assessment of the external conditions at an offshore
       wind turbine site
    13 Assembly, installation and erection
    14 Commissioning, operation and maintenance
    Annex A (informative) - Key design parameters for an
            offshore wind turbine
    Annex B (informative) - Wave spectrum formulations
    Annex C (informative) - Shallow water hydrodynamics
            and breaking waves
    Annex D (informative) - Guidance on calculation of
            hydrodynamic loads
    Annex E (informative) - Recommendations for design of
            offshore wind turbine support structures with
            respect to ice loads
    Annex F (informative) - Offshore wind turbine foundation
            design
    Annex G (informative) - Statistical extrapolation of
            operational metocean parameters for ultimate
            strength analysis
    Annex H (informative) - Corrosion protection
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes additional requirements for assessment of the external conditions at an offshore wind turbine site and also specifies essential design requirements to ensure the engineering integrity of offshore wind turbines.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Product Note Reconfirmed EN
    Publisher Canadian Standards Association
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61000-6-4:2006+AMD1:2010 CSV ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS
    ISO 19901-6:2009 Petroleum and natural gas industries — Specific requirements for offshore structures — Part 6: Marine operations
    IEC 60898:1995 Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations
    ISO 3010:2017 Bases for design of structures — Seismic actions on structures
    IEC 61310-2:2007 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
    CSA C61400-1 : 2014 WIND TURBINES - PART 1: DESIGN REQUIREMENTS
    IEC 61000-6-2:2016 Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments
    IEC 61400-24:2010 Wind turbines - Part 24: Lightning protection
    ISO 4354:2009 Wind actions on structures
    IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
    ISO 2394:2015 General principles on reliability for structures
    IEC 61000-6-1 : 3.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-1: GENERIC STANDARDS - IMMUNITY STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS
    IEC 60204-11:2000 Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV
    IEC TS 61400-13:2001 Wind turbine generator systems - Part 13: Measurement of mechanical loads
    ISO 2533:1975 Standard Atmosphere
    ISO 17776:2016 Petroleum and natural gas industries Offshore production installations Major accident hazard management during the design of new installations
    ISO 15544:2000 Petroleum and natural gas industries — Offshore production installations — Requirements and guidelines for emergency response
    NACE RP 01 76 : 2003 CORROSION CONTROL OF STEEL FIXED OFFSHORE STRUCTURES ASSOCIATED WITH PETROLEUM PRODUCTION
    API 2A : 1986 RECOMMENDED PRACTICE FOR PLANNING, DESIGNING AND CONSTRUCTING FIXED OFFSHORE PLATFORMS
    ISO 13819-2:1995 Petroleum and natural gas industries Offshore structures Part 2: Fixed steel structures
    IEC 60721-2-1:2013 Classification of environmental conditions - Part 2-1: Environmental conditions appearing in nature - Temperature and humidity
    CSA ISO 19901-1 : 2016 PETROLEUM AND NATURAL GAS INDUSTRIES - SPECIFIC REQUIREMENTS FOR OFFSHORE STRUCTURES - PART 1: METOCEAN DESIGN AND OPERATING CONSIDERATIONS
    ISO 19906:2010 Petroleum and natural gas industries Arctic offshore structures
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 60755:2017 General safety requirements for residual current operated protective devices
    IEC 61000-6-1:2016 Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity standard for residential, commercial and light-industrial environments
    ISO 9001:2015 Quality management systems - Requirements
    STG 2215 : 1998 RICHTLINIEN FUER KORROSIONSSCHUTZ FUER SCHIFFE UND SEEBAUWERKE - TEIL 1: "SCHIFF, SEEBAUWERK UND AUSRUESTUNG - NEUBAU"
    IEC 61000-6-4:2006+AMD1:2010 CSV Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments
    ISO 8930:1987 General principles on reliability for structures List of equivalent terms
    CSA ISO 9001 : 2016 QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS
    IEC 62305-4:2010 Protection against lightning - Part 4: Electrical and electronic systems within structures
    IEC 61310-1:2007 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
    IEC 60173:1964 Colours of the cores of flexible cables and cords
    CSA ISO 19900 : 2014 PETROLEUM AND NATURAL GAS INDUSTRIES - GENERAL REQUIREMENTS FOR OFFSHORE STRUCTURES
    IEC 61000-6-2 : 3.0:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS
    CAN/CSA-ISO 19901-4:17 Petroleum and natural gas industries — Specific requirements for offshore structures — Part 4: Geotechnical and foundation design considerations (Adopted ISO 19901-4:2016, second edition, 2016-07-15)
    S6-14 Canadian Highway Bridge Design Code
    IEC 62305-3:2010 Protection against lightning - Part 3: Physical damage to structures and life hazard
    NORSOK M 501 : REV 6 SURFACE PREPARATION AND PROTECTIVE COATING
    IEC 61400-21:2008 Wind turbines - Part 21: Measurement and assessment of power quality characteristics of grid connected wind turbines
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective