Skip to content
Please enter a keyword to search

  • CSA C62155 : 2006 : R2015

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    HOLLOW PRESSURIZED AND UNPRESSURIZED CERAMIC AND GLASS INSULATORS FOR USE IN ELECTRICAL EQUIPMENT WITH RATED VOLTAGES GREATER THAN 1000 V

    Available format(s):  Hardcopy, PDF

    Superseded date:  10-01-2016

    Language(s):  English

    Published date:  01-01-2015

    Publisher:  Canadian Standards Association

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    1 Scope and object
    2 Normative references
    3 Terms and definitions
    4 Insulating materials
    5 General recommendations for design
    6 Classification of the tests, sampling rules and procedures
    7 General test procedures and requirements
    8 Type tests
    9 Sample tests
    10 Routine tests
    11 Documentation
    Annex A (informative) - Methods of testing for tolerances
            of parallelism, coaxiality, eccentricity, angular
            deviation, camber and shed angle of hollow
            insulators or hollow insulator bodies
    Annex B (informative) - Methods for bending tests of
            hollow insulator bodies
    Annex C (informative) - Alternative test method for the
            temperature-cycle test
    Annex D (informative) - Bending moment equivalent
            to the design pressure
    Bibliography

    Abstract - (Show below) - (Hide below)

    Applies to: - ceramic and glass hollow insulators intended for general use in electrical equipment; - ceramic hollow insulators intended for use with a permanent gas pressure in switchgear and controlgear.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes CSA C1264 (09/2006)
    Document Type Standard
    Product Note Reconfirmed EN
    Publisher Canadian Standards Association
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 62271-100:2008+AMD1:2012+AMD2:2017 CSV High-voltage switchgear and controlgear - Part 100: Alternating-current circuit-breakers
    ISO 4287:1997 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
    IEEE C37.013-1997 IEEE Standard for AC High-Voltage Generator Circuit Breakers Rated on a Symmetrical Current Basis
    IEC TS 61462:1998 Composite insulators - Hollow insulators for use in outdoor and indoor electrical equipment - Definitions, test methods, acceptance criteria and design recommendations
    IEC 60050-471:2007 International Electrotechnical Vocabulary (IEV) - Part 471: Insulators
    ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
    IEC 60672-3:1997 Ceramic and glass-insulating materials - Part 3: Specifications for individual materials
    ISO 1463:2003 Metallic and oxide coatings Measurement of coating thickness Microscopical method
    ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
    IEC 61166:1993 High-voltage alternating current circuit-breakers - Guide for seismic qualification of high-voltage alternating current circuit-breakers
    ISO 9002:1994 Quality systems — Model for quality assurance in production, installation and servicing
    IEC 60694:1996+AMD1:2000+AMD2:2001 CSV Common specifications for high-voltage switchgear and controlgear standards
    IEC 60865-1:2011 Short-circuit currents - Calculation of effects - Part 1: Definitions and calculation methods
    IEC TR 60865-2:2015 Short-circuit currents - Calculation of effects - Part 2: Examples of calculation
    IEC 60437:1997 Radio interference test on high-voltage insulators
    IEC TS 61245:2015 Artificial pollution tests on high-voltage ceramic and glass insulators to be used on d.c. systems
    IEC 60273:1990 Characteristic of indoor and outdoor post insulators for systems with nominal voltages greater than 1000 V
    IEEE C37.09-1999 IEEE Standard Test Procedure for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis
    ISO 2178:2016 Non-magnetic coatings on magnetic substrates Measurement of coating thickness Magnetic method
    CSA ISO 9001 : 2016 QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS
    ISO 9003:1994 Quality systems Model for quality assurance in final inspection and test
    ISO 1460:1992 Metallic coatings Hot dip galvanized coatings on ferrous materials Gravimetric determination of the mass per unit area
    IEC 60507:2013 Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems
    ISO 2064:1996 Metallic and other inorganic coatings — Definitions and conventions concerning the measurement of thickness
    IEEE C37.04-1999 IEEE Standard Rating Structure for AC High-Voltage Circuit Breakers
    IEC 60168:1994+AMD1:1997+AMD2:2000 CSV Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1000 V
    IEC TS 61463:2016 Bushings - Seismic qualification
    IEC 60672-1:1995 Ceramic and glass insulating materials - Part 1: Definitions and classification
    CSA ISO 9000 : 2016 QUALITY MANAGEMENT SYSTEMS - FUNDAMENTALS AND VOCABULARY
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective