Skip to content
Please enter a keyword to search

  • DIN EN 16506 E : 2014

    Current The latest, up-to-date edition.

    SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2014

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National foreword
    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviations
    5 Pipes at the 'M' stage
    6 Marking
    7 Fittings at the 'M' stage
    8 Lining system at the 'I' stage
    9 Installation
    10 Documentation
    Annex A (normative) - Test method for anchoring
            strength of plastics inner layer by pull-off
    Annex B (normative) - 'I' stage crushing strength test
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines performance requirements and test methods for pipes and fittings for the renovation of underground drain and sewer systems by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 10048:1996 Hot rolled narrow steel strip - Tolerances on dimensions and shape
    EN 15885:2010 Classification and characteristics of techniques for renovation and repair of drains and sewers
    EN 728:1997 Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
    EN 1107-2 : 2001 Flexible sheets for waterproofing - Determination of dimensional stability - Part 2: Plastic and rubber sheets for roof waterproofing
    ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
    EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
    EN 1542:1999 Products and systems for the protection and repair of concrete structures - Test methods - Measurement of bond strength by pull-off
    ISO 2039-1:2001 Plastics Determination of hardness Part 1: Ball indentation method
    EN 14654-1:2014 Management and control of operational activities in drain and sewer systems outside buildings - Part 1: Cleaning
    EN ISO 1133-2:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011)
    EN ISO 11296-7:2013 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes (ISO 11296-7:2011)
    EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
    EN ISO 6259-1:2015 Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015)
    ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
    EN 13380:2001 General requirements for components used for renovation and repair of drain and sewer systems outside buildings
    CEN/TR 14920:2005 Jetting resistance of drain and sewer pipes - Moving jet test method
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
    ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
    EN 445:2007 Grout for prestressing tendons - Test methods
    EN 196-1:2016 Methods of testing cement - Part 1: Determination of strength
    EN ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
    EN 13412:2006 Products and systems for the protection and repair of concrete structures - Test methods - Determination of modulus of elasticity in compression
    ISO 4624:2016 Paints and varnishes — Pull-off test for adhesion
    ISO 11296-7:2011 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 7: Lining with spirally-wound pipes
    EN ISO 1133-1:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
    EN 1979:1999 Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam
    EN ISO 2039-1 : 2003 PLASTICS - DETERMINATION OF HARDNESS - PART 1: BALL INDENTATION METHOD (ISO 2039-1:2001)
    ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
    ISO 11296-4:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 4: Lining with cured-in-place pipes
    EN 13100-4:2012 Non destructive testing of welded joints of thermoplastics semifinished products - Part 4: High voltage testing
    EN 12814-2:2000 TESTING OF WELDED JOINTS OF THERMOPLASTICS SEMI-FINISHED PRODUCTS - PART 2: TENSILE TEST
    EN ISO 4624:2016 Paints and varnishes - Pull-off test for adhesion (ISO 4624:2016)
    EN 10025-2:2004/AC:2005 HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS
    EN 1015-3:1999/A2:2006 METHODS OF TEST FOR MORTAR FOR MASONRY - PART 3: DETERMINATION OF CONSISTENCE OF FRESH MORTAR (BY FLOW TABLE)
    EN 1015-6:1998/A1:2006 METHODS OF TEST FOR MORTAR FOR MASONRY - PART 6: DETERMINATION OF BULK DENSITY OF FRESH MORTAR
    EN 1610:2015 Construction and testing of drains and sewers
    EN 1916:2002/AC:2008 CONCRETE PIPES AND FITTINGS, UNREINFORCED, STEEL FIBRE AND REINFORCED
    EN 13067:2012 Plastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies
    ISO 1133-2:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
    ISO 527-3:1995 Plastics Determination of tensile properties Part 3: Test conditions for films and sheets
    EN ISO 527-3:1995/AC:2002 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 3: TEST CONDITIONS FOR FILMS AND SHEETS
    EN 14117:2004 Products systems for the protection and repair of concrete structures - Test methods - Determination of time of efflux of cementitious injection products
    EN 206:2013+A1:2016 Concrete - Specification, performance, production and conformity
    EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)
    EN 12814-8:2001/AC:2003 TESTING OF WELDED JOINTS OF THERMOPLASTICS SEMI-FINISHED PRODUCTS - PART 8: REQUIREMENTS
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective