• DIN EN ISO 17409 E : 2017

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    ELECTRICALLY PROPELLED ROAD VEHICLES - CONNECTION TO AN EXTERNAL ELECTRIC POWER SUPPLY - SAFETY REQUIREMENTS (ISO 17409:2015, CORRECTED VERSION 2015-12-15)

    Available format(s):  Hardcopy, PDF

    Superseded date:  04-11-2020

    Language(s):  English

    Published date:  01-01-2017

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National foreword
    European foreword
    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Environmental conditions
    5 Requirements for protection of persons
       against electric shock
    6 Protection against thermal incident
    7 Specific requirements for the vehicle inlet,
       plug, and cable
    8 Additional requirements for a.c. electric
       power supply
    9 Additional requirements for d.c. electric
       power supply
    10 Operational requirements
    11 Owner's manual and marking
    12 Test procedure
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines electric safety requirements for conductive connections of electrically propelled road vehicles to an external electric power supply using a plug or vehicle inlet.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
    IEC 60364-5-54:2011 Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors
    IEC 60038:2009 IEC standard voltages
    ISO 6469-2:2009 Electrically propelled road vehicles Safety specifications Part 2: Vehicle operational safety means and protection against failures
    IEC 60364-4-43:2008 Low-voltage electrical installations - Part 4-43: Protection for safety - Protection against overcurrent
    ISO 16750-4:2010 Road vehicles Environmental conditions and testing for electrical and electronic equipment Part 4: Climatic loads
    IEC 62196-2:2016 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories
    IEC TS 62763:2013 Pilot function through a control pilot circuit using PWM (pulse width modulation) and a control pilot wire
    IEC 62196-3:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers
    IEC 60884-1:2002+AMD1:2006+AMD2:2013 CSV Plugs and socket-outlets for household and similar purposes - Part1: General requirements
    ISO 6469-1:2009 Electrically propelled road vehicles Safety specifications Part 1: On-board rechargeable energy storage system (RESS)
    ISO 20653:2013 Road vehicles Degrees of protection (IP code) Protection of electrical equipment against foreign objects, water and access
    IEC 60364-6:2016 Low voltage electrical installations - Part 6: Verification
    ISO 6469-3:2011 Electrically propelled road vehicles Safety specifications Part 3: Protection of persons against electric shock
    IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements
    IEC 61851-1:2017 Electric vehicle conductive charging system - Part 1: General requirements
    IEC 60309-2:1999+AMD1:2005+AMD2:2012 CSV PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 2: DIMENSIONAL INTERCHANGEABILITY REQUIREMENTS FOR PIN AND CONTACT-TUBE ACCESSORIES
    IEC 60990:2016 Methods of measurement of touch current and protective conductor current
    IEC 60364-5-52:2009 Low-voltage electrical installations - Part 5-52: Selection and erection of electrical equipment - Wiring systems
    IEC 62196-1:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective