|
DIN 32564-1:2004-05
|
Production equipment for micro-systems - Terms and definitions - Part 1: General terms of micro-system technology |
|
EN 50295:1999
|
Low-voltage switchgear and controlgear - Controller and device interface systems - Actuator Sensor interface (AS-i) |
|
ISO/IEC 24702:2006
|
Information technology Generic cabling Industrial premises |
|
ISO 1101:2017
|
Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
|
IEEE 802.3-2012
|
IEEE Standard for Ethernet |
|
VDE 0140-1:2016-11
|
PROTECTION AGAINST ELECTRIC SHOCK - COMMON ASPECTS FOR INSTALLATION AND EQUIPMENT (IEC 61140:2016) |
|
TIA/EIA 568-2 : C2009 AMD 1 2016
|
COMMERCIAL BUILDING TELECOMMUNICATIONS CABLING STANDARD - PART 2: BALANCED TWISTED-PAIR TELECOMMUNICATIONS CABLING AND COMPONENTS STANDARDS |
|
ISO/IEC 11801:2002
|
Information technology Generic cabling for customer premises |
|
ISO 9409-2:2002
|
Manipulating industrial robots Mechanical interfaces Part 2: Shafts |
|
IEC 62026-2:2008
|
Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 2: Actuator sensor interface (AS-i) |
|
DIN EN ISO 9787 E : 2000
|
MANIPULATING INDUSTRIAL ROBOTS - COORDINATE SYSTEMS AND MOTION NOMENCLATURES |
|
ISO 3650:1998
|
Geometrical Product Specifications (GPS) Length standards Gauge blocks |
|
VDE 0411-500 : 2008 COR 1 2009
|
PROGRAMMABLE CONTROLLERS - PART 2: EQUIPMENT REQUIREMENTS AND TESTS |
|
ISO 286-1:2010
|
Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
|
DIN EN ISO 8734 E : 1998
|
PARALLEL PINS OF HARDENED STEEL AND MARTENSITIC STAINLESS STEEL (DOWEL PINS) |
|
ISO 9409-1:2004
|
Manipulating industrial robots — Mechanical interfaces — Part 1: Plates |
|
DIN EN 61140 : 2016-11
|
PROTECTION AGAINST ELECTRIC SHOCK - COMMON ASPECTS FOR INSTALLATION AND EQUIPMENT (IEC 61140:2016) |
|
ISO 286-2:2010
|
Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
|
ISO/IEC 24740:2008
|
Information technology Responsive Link (RL) |
|
ISO 9787:2013
|
Robots and robotic devices Coordinate systems and motion nomenclatures |
|
IEC 61131-2:2017
|
Industrial-process measurement and control - Programmable controllers - Part 2: Equipment requirements and tests |
|
DIN 7154-1:1966-08
|
ISO-FITS FOR THE HOLE BASIS SYSTEM; TOLERANCE ZONES, DEVIATIONS |
|
IEC 61140:2016
|
Protection against electric shock - Common aspects for installation and equipment |
|
ISO 8734:1997
|
Parallel pins, of hardened steel and martensitic stainless steel (Dowel pins) |
|
DIN 7154-2:1966-08
|
ISO-FITS FOR THE HOLE BASIC SYSTEM; TOLERANCES OF FIT (CLEARANCES AND INTERFERENCES) |
|
IEC TR 60479-3:1998
|
Effects of current on human beings and livestock - Part 3: Effects of currents passing through the body of livestock |
|
DIN EN 61131-2 : 2008 COR 1 2009
|
PROGRAMMABLE CONTROLLERS - PART 2: EQUIPMENT REQUIREMENTS AND TESTS |
|
ISO 18265:2013
|
Metallic materials — Conversion of hardness values |