• EN 61810-1:2015/AC:2018-04

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    ELECTROMECHANICAL ELEMENTARY RELAYS - PART 1: GENERAL AND SAFETY REQUIREMENTS (IEC 61810-1:2015/COR1:2018)

    Available format(s): 

    Superseded date:  17-03-2020

    Language(s): 

    Published date:  12-01-2013

    Publisher:  European Committee for Standards - Electrical

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Influence quantities
    5 Rated values
    6 General provisions for testing
    7 Documentation and marking
    8 Heating
    9 Basic operating function
    10 Dielectric strength
    11 Electrical endurance
    12 Mechanical endurance
    13 Clearances, creepage distances and solid insulation
    14 Terminations
    15 Sealing
    16 Heat and fire resistance
    Annex A (normative) - Explanations regarding relays
    Annex B (informative) - Inductive contact loads
    Annex C (normative) - Test set-up
    Annex D (informative) - Special loads
    Annex E (normative) - Heating test arrangement
    Annex F (normative) - Measurement of clearances and
            creepage distances
    Annex G (normative) - Relation between rated impulse
            voltage, nominal voltage and overvoltage category
    Annex H (normative) - Pollution degrees
    Annex I (normative) - Proof tracking test
    Annex J (informative) - Schematic diagram of families
            of terminations
    Annex K (normative) - Glow-wire test
    Annex L (normative) - Ball pressure test
    Annex M (informative) - Needle flame test
    Annex N (informative) - Resistance for standard
            soldering processes
    Annex O (informative) - Risk assessment
    Alphabetical list of terms
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    Pertains to electromechanical elementary relays (non-specified time all or-nothing relays) for incorporation into low voltage equipment (circuits up to 1000 V alternate current or 1500 V direct current).

    General Product Information - (Show below) - (Hide below)

    Committee TC 94
    Development Note Supersedes EN 60255-1-00 (04/2001) Supersedes EN 61810-5 (03/2004)
    Document Type Standard
    Publisher European Committee for Standards - Electrical
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
    IEC 60112:2003+AMD1:2009 CSV METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS
    IEC 60038:2009 IEC standard voltages
    IEC 60664-4:2005 Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress
    IEC 61984:2008 Connectors - Safety requirements and tests
    IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
    EN 60085 : 2008 ELECTRICAL INSULATION - THERMAL EVALUATION AND DESIGNATION
    EN 60068-2-20 : 2008 ENVIRONMENTAL TESTING - PART 2-20: TESTS - TEST T: TEST METHODS FOR SOLDERABILITY AND RESISTANCE TO SOLDERING HEAT OF DEVICES WITH LEADS
    EN 60079-15 : 2010 EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION "N"
    EN 60068-2-2:2007 ENVIRONMENTAL TESTING - PART 2-2: TESTS - TEST B: DRY HEAT
    IEC 61210:2010 Connecting devices - Flat quick-connect terminations for electrical copper conductors - Safety requirements
    EN 61760-1 : 2006 SURFACE MOUNTING TECHNOLOGY - PART 1: STANDARD METHOD FOR THE SPECIFICATION OF SURFACE MOUNTING COMPONENTS (SMDS)
    IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
    IEC 61760-1:2006 Surface mounting technology - Part 1: Standard method for the specification of surface mounting components (SMDs)
    IEC 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
    ANSI B11 TR3 : 2000 RISK ASSESSMENT AND RISK REDUCTION - A GUIDE TO ESTIMATE, EVALUATE AND REDUCE RISKS ASSOCIATED WITH MACHINE TOOLS
    EN 60099-1:1994/A1:1999 SURGE ARRESTERS - PART 1: NON-LINEAR RESISTOR TYPE GAPPED SURGE ARRESTERS FOR A.C. SYSTEMS
    IEC 60695-2-13:2010+AMD1:2014 CSV Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods- Glow-wire ignition temperature (GWIT) test method for materials
    IEC 61810-7:2006 Electromechanical elementary relays - Part 7: Test and measurement procedures
    EN 60112 : 2003 AMD 1 2009 METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS
    IEC 60999-1:1999 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included)
    HD 60364-4-442 : 2012 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-442: PROTECTION FOR SAFETY - PROTECTION OF LOW-VOLTAGE INSTALLATIONS AGAINST TEMPORARY OVERVOLTAGES DUE TO EARTH FAULTS IN THE HIGH-VOLTAGE SYSTEM AND DUE TO FAULTS IN THE LOW VOLTAGE SYSTEM (IEC 60364-4-44:2007 (CLAUSE 442), MODIFIED)
    EN 60695-2-13:2010/A1:2014 FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS (IEC 60695-2-13:2010/A1:2014)
    IEC 60085:2007 ELECTRICAL INSULATION - THERMAL EVALUATION AND DESIGNATION
    IEC 60695-2-12:2010+AMD1:2014 CSV Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods- Glow-wire flammability index (GWFI) test method for materials
    SEMI S10 : 2015E SAFETY GUIDELINE FOR RISK ASSESSMENT AND RISK EVALUATION PROCESS
    EN 60068-2-17 : 1994 BASIC ENVIRONMENTAL TESTING - TEST Q: SEALING
    IEC 60068-2-17:1994 Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
    EN 60695-2-10 : 2013 FIRE HAZARD TESTING - PART 2-10: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE APPARATUS AND COMMON TEST PROCEDURE (IEC 60695-2-10:2013)
    IEC 60364-4-44:2007+AMD1:2015 CSV Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances
    IEC 60099-1:1991+AMD1:1999 CSV Surge arresters - Part 1: Non-linear resistor type gapped surge arresters for a.c. systems
    IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
    EN 60664-1 : 2007 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS
    IEC 60669-1:2017 Switches for household and similar fixed-electrical installations - Part 1: General requirements
    IEC 60664-5:2007 Insulation coordination for equipment within low-voltage systems - Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm
    IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations
    EN 61210 : 2010 Connecting devices - Flat quick-connect terminations for electrical copper conductors - Safety requirements
    IEC 60664-3:2016 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 3: USE OF COATING, POTTING OR MOULDING FOR PROTECTION AGAINST POLLUTION
    EN 60999-1 : 2000 CONNECTING DEVICES - ELECTRICAL COPPER CONDUCTORS - SAFETY REQUIREMENTS FOR SCREW-TYPE AND SCREWLESS-TYPE CLAMPING UNITS - PART 1: GENERAL REQUIREMENTS AND PARTICULAR REQUIREMENTS FOR CLAMPING UNITS FOR CONDUCTORS FROM 0,2 MM[2] UP TO 35 MM[2] (INCLUDED)
    EN 61984 : 2009 CONNECTORS - SAFETY REQUIREMENTS AND TESTS
    IEC 60695-10-2:2014 FIRE HAZARD TESTING - PART 10-2: ABNORMAL HEAT - BALL PRESSURE TEST METHOD
    EN 60664-4:2006/corrigendum:2006 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 4: CONSIDERATION OF HIGH-FREQUENCY VOLTAGE STRESS
    IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
    EN 60664-5 : 2007 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 5: COMPREHENSIVE METHOD FOR DETERMINING CLEARANCES AND CREEPAGE DISTANCES EQUAL TO OR LESS THAN 2 MM
    IEC 60695-11-5 : 2.0 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
    IEC 60695-2-10:2013 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
    EN 60695-2-12:2010/A1:2014 FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS (IEC 60695-2-12:2010/A1:2014)
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    EN 60664-3 : 2017 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 3: USE OF COATING, POTTING OR MOULDING FOR PROTECTION AGAINST POLLUTION (IEC 60664-3:2016)
    IEC 60079-15:2010 Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
    EN 60038 : 2011 CENELEC STANDARD VOLTAGES (IEC 60038:2009, MODIFIED)
    EN 60695-2-11 : 2014 FIRE HAZARD TESTING - PART 2-11: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY TEST METHOD FOR END-PRODUCTS (GWEPT) (IEC 60695-2-11:2014)
    IEC 60730-1:2013+AMD1:2015 CSV Automatic electrical controls - Part 1: General requirements
    EN 60721-3-3 : 95 AMD 2 97 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STATIONARY USE AT WEATHER-PROTECTED LOCATIONS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective