• EN 62282-3-200:2016 (edition 2)

    Current The latest, up-to-date edition.

    Fuel cell technologies - Part 3-200: Stationary fuel cell power systems - Performance test methods

    Available format(s): 

    Language(s): 

    Published date:  11-03-2016

    Publisher:  European Committee for Standards - Electrical

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms, definitions, operating process and symbols
    4 Reference conditions
    5 Item of performance test
    6 Test preparation
    7 Measurement instruments and measurement
       methods
    8 Test plan
    9 Test methods and computation of test results
    10 Test reports
    Annex A (normative) - Uncertainty analysis
    Annex B (normative) - Calculation of fuel heating
            value
    Annex C (normative) - Reference gas
    Annex D (informative) - Maximum acceptable instantaneous
            electric power output transient
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    IEC 62282-3-200:2015 covers operational and environmental aspects of the stationary fuel cell power systems performance. The test methods apply as follows:- power output under specified operating and transient conditions;- electrical and heat recovery efficiency under specified operating conditions;- environmental characteristics;- for example, exhaust gas emissions, noise, etc. under specified operating and transient conditions. This new edition includes the following significant technical changes with respect to the previous edition: a stabilization zone of +- 10 % for thermal output of 100 % response time is provided instead of the tests for thermal output of 90 % response time, while the tests for electric output of 90 % response time remain as an option; the calculations for the ramp rate in kW/s are deleted and only the calculations for the response time (s) remain.

    General Product Information - (Show below) - (Hide below)

    Committee CLC/SR 105
    Development Note Supersedes EN 62282-3-2. (01/2012)
    Document Type Standard
    Publisher European Committee for Standards - Electrical
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    CEI EN 62282-3-201 : 2014 FUEL CELL TECHNOLOGIES - PART 3-201: STATIONARY FUEL CELL POWER SYSTEMS - PERFORMANCE TEST METHODS FOR SMALL FUEL CELL POWER SYSTEMS
    UNE-EN 62282-3-201:2013 Fuel cell technologies - Part 3-201: Stationary fuel cell power systems - Performance test methods for small fuel cell power systems
    CEI EN 62282-3-100 : 2012 FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    BS EN 62282-3-100 : 2012 FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    BS EN 62282-3-201:2017 Fuel cell technologies Stationary fuel cell power systems. Performance test methods for small fuel cell power systems
    I.S. EN 62282-3-201:2017 FUEL CELL TECHNOLOGIES - PART 3-201: STATIONARY FUEL CELL POWER SYSTEMS - PERFORMANCE TEST METHODS FOR SMALL FUEL CELL POWER SYSTEMS
    I.S. EN 62282-3-100:2012 FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-3-100:2012 (EQV))
    EN 62282-3-100 : 2012 FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-3-100:2012)
    EN 62282-3-201:2017 (edition 2) Fuel cell technologies - Part 3-201: Stationary fuel cell power systems - Performance test methods for small fuel cell power systems

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/TR 15916:2015 Basic considerations for the safety of hydrogen systems
    EN 60688:2013 ELECTRICAL MEASURING TRANSDUCERS FOR CONVERTING A.C. AND D.C. ELECTRICAL QUANTITIES TO ANALOGUE OR DIGITAL SIGNALS (IEC 60688:2012)
    IEC 61672-2:2013+AMD1:2017 CSV Electroacoustics - Sound level meters - Part 2: Pattern evaluation tests
    EN ISO 11541 : 2002 NATURAL GAS - DETERMINATION OF WATER CONTENT AT HIGH PRESSURE
    ISO 3648:1994 Aviation fuels Estimation of net specific energy
    ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
    ISO 6976:2016 Natural gas Calculation of calorific values, density, relative density and Wobbe indices from composition
    ISO 14687-3:2014 Hydrogen fuel Product specification Part 3: Proton exchange membrane (PEM) fuel cell applications for stationary appliances
    EN 60359 : 2002 ELECTRICAL AND ELECTRONIC MEASUREMENT EQUIPMENT - EXPRESSION OF PERFORMANCE
    EN 61672-2:2013/A1:2017 ELECTROACOUSTICS - SOUND LEVEL METERS - PART 2: PATTERN EVALUATION TESTS (IEC 61672-2:2013/A1:2017)
    ISO 11086:1996 Gas turbines Vocabulary
    IEC 60050-151:2001 International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices
    IEC TS 62282-1:2013 Fuel cell technologies - Part 1: Terminology
    IEC 60688:2012 Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals
    EN ISO 10523 : 2012 WATER QUALITY - DETERMINATION OF PH (ISO 10523:2008)
    EN 61000-4-7:2002/A1:2009 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO (IEC 61000-4-7:2002/A1:2008)
    ISO 6975:1997 Natural gas Extended analysis Gas-chromatographic method
    ISO 7935:1992 Stationary source emissions Determination of the mass concentration of sulfur dioxide Performance characteristics of automated measuring methods
    IEC 62052-11:2003+AMD1:2016 CSV Electricity metering equipment (a.c.) - General requirements, tests and test conditions - Part 11: Metering equipment
    ISO 8217:2017 Petroleum products Fuels (class F) Specifications of marine fuels
    ASTM F 2602 : 2013-10 TEST METHOD FOR DETERMINING THE MOLAR MASS OF CHITOSAN AND CHITOSAN SALTS BY SIZE EXCLUSION CHROMATOGRAPHY WITH MULTI-ANGLE LIGHT SCATTERING DETECTION (SEC-MALS)
    ISO 6060:1989 Water quality — Determination of the chemical oxygen demand
    ISO 4677-1:1985 Atmospheres for conditioning and testing Determination of relative humidity Part 1: Aspirated psychrometer method
    ISO 16622:2002 Meteorology Sonic anemometers/thermometers Acceptance test methods for mean wind measurements
    ISO 11042-1:1996 Gas turbines Exhaust gas emission Part 1: Measurement and evaluation
    ISO 11042-2:1996 Gas turbines Exhaust gas emission Part 2: Automated emission monitoring
    EN 61672-1:2013 ELECTROACOUSTICS - SOUND LEVEL METERS - PART 1: SPECIFICATIONS (IEC 61672-1:2013)
    EN ISO 3744:2010 ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE
    EN 50470-1:2006 ELECTRICITY METERING EQUIPMENT (A.C.) - PART 1: GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS - METERING EQUIPMENT (CLASS INDEXES A, B AND C)
    ISO 11541:1997 Natural gas Determination of water content at high pressure
    EN 62282-3-201:2017 (edition 2) Fuel cell technologies - Part 3-201: Stationary fuel cell power systems - Performance test methods for small fuel cell power systems
    EN ISO 6975 : 2005 NATURAL GAS - EXTENDED ANALYSIS - GAS-CHROMATOGRAPHIC METHOD
    IEC 61000-4-7:2002+AMD1:2008 CSV Electromagnetic compatibility (EMC) - Part 4-7: Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto
    IEC 62053-22:2003+AMD1:2016 CSV Electricity metering equipment (a.c.) - Particular Requirements - Part 22: Static meters for active energy (classes 0,2 S and 0,5 S)
    ISO 9000:2015 Quality management systems Fundamentals and vocabulary
    IEC 60359:2001 Electrical and electronic measurement equipment - Expression of performance
    ISO 5815-2:2003 Water quality Determination of biochemical oxygen demand after n days (BODn) Part 2: Method for undiluted samples
    ISO 5348:1998 Mechanical vibration and shock Mechanical mounting of accelerometers
    ISO 10849:1996 Stationary source emissions Determination of the mass concentration of nitrogen oxides Performance characteristics of automated measuring systems
    ISO 10780:1994 Stationary source emissions Measurement of velocity and volume flowrate of gas streams in ducts
    EN 61028:1993/A2:1997 ELECTRICAL MEASURING INSTRUMENTS - X-Y RECORDERS
    EN ISO 6976:2016 NATURAL GAS - CALCULATION OF CALORIFIC VALUES, DENSITY, RELATIVE DENSITY AND WOBBE INDICES FROM COMPOSITION (ISO 6976:2016)
    ISO 10523:2008 Water quality — Determination of pH
    ISO 10396:2007 Stationary source emissions Sampling for the automated determination of gas emission concentrations for permanently-installed monitoring systems
    IEC 61028:1990 Electrical measuring instruments - X-Y recorders
    ISO 4677-2:1985 Atmospheres for conditioning and testing Determination of relative humidity Part 2: Whirling psychrometer method
    EN 61000-4-13:2002/A2:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-13: TESTING AND MEASUREMENT TECHNIQUES - HARMONICS AND INTERHARMONICS INCLUDING MAINS SIGNALLING AT A.C. POWER PORT, LOW FREQUENCY IMMUNITY TESTS (IEC 61000-4-13:2002/A2:2015)
    IEC 60050-300:2001 International Electrotechnical Vocabulary (IEV) - Part 300: Electrical and electronic measurements and measuring instruments - Part 311: General terms relating to measurements - Part 312: General terms relating to electrical measurements - Part 313: Types of electrical measuring instruments - Part 314: Specific terms according to the type of instrument
    IEC 62282-3-201:2017 Fuel cell technologies - Part 3-201: Stationary fuel cell power systems - Performance test methods for small fuel cell power systems
    IEC 61000-4-13:2002+AMD1:2009+AMD2:2015 CSV Electromagnetic compatibility (EMC) - Part 4-13: Testing and measurement techniques - Harmonics and interharmonics includingmains signalling at a.c. power port, low frequency immunity tests
    EN ISO 9000 : 2015 QUALITY MANAGEMENT SYSTEMS - FUNDAMENTALS AND VOCABULARY (ISO 9000:2015)
    ISO/IEC Guide 98-3:2008 Uncertainty of measurement Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)
    ISO 11632:1998 Stationary source emissions Determination of mass concentration of sulfur dioxide Ion chromatography method
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective