Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN IEC 60099-5:2018

    Current The latest, up-to-date edition.

    SURGE ARRESTERS - PART 5: SELECTION AND APPLICATION RECOMMENDATIONS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  16-04-2018

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National foreword
    FOREWORD
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General principles for the application of surge arresters
    5 Surge arrester fundamentals and applications issues
    6 Insulation coordination and surge arrester applications
    7 Surge arresters for special applications
    8 Asset management of surge arresters
    Annex A (informative) - Determination of temporary
            overvoltages due to earth faults
    Annex B (informative) - Current practice
    Annex C (informative) - Arrester modelling techniques
            for studies involving insulation coordination and
            energy requirements
    Annex D (informative) - Diagnostic indicators of
            metal-oxide surge arresters in service
    Annex E (informative) - Typical data needed from
            arrester manufacturers for proper selection
            of surge arresters
    Annex F (informative) - Typical maximum residual voltages
            for metal-oxide arresters without gaps according
            to IEC 60099-4
    Annex G (informative) - Steepness reduction of incoming
            surge with additional line terminal surge capacitance
    Annex H (informative) - Comparison of the former energy
            classification system based on line discharge classes
            and the present classification system based on thermal
            energy ratings for operating duty tests and repetitive
            charge transfer ratings for repetitive single
            event energies
    Annex I (informative) - Estimation of arrester cumulative
            charges and energies during line switching
    Annex J (informative) - End of life and replacement of old
            gapped SiC-arresters
    Bibliography
    Annex ZA (normative) -Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    Gives information, guidance, and recommendations for the selection and application of surge arresters to be used in three-phase systems with nominal voltages above 1 kV.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. EN 60099-5. (04/2018)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 62271-200:2011 High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
    IEC 60099-4:2014 Surge arresters - Part 4: Metal-oxide surge arresters without gaps for a.c. systems
    IEC TR 60071-4:2004 Insulation co-ordination - Part 4: Computational guide to insulation co-ordination and modelling of electrical networks
    EN 62271-203:2012 High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV
    IEC TR 62271-300:2006 High-voltage switchgear and controlgear - Part 300: Seismic qualification of alternating current circuit-breakers
    EN 60099-4:2014 Surge arresters - Part 4: Metal-oxide surge arresters without gaps for a.c. systems
    IEC 60099-6:2002 Surge arresters - Part 6: Surge arresters containing both series and parallel gapped structures - Rated 52 kV and less
    EN 60507:2014 Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems
    IEC 62271-203:2011 High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV
    EN 60071-1:2006/A1:2010 INSULATION CO-ORDINATION - PART 1: DEFINITIONS, PRINCIPLES AND RULES
    IEC 60071-2:1996 Insulation co-ordination - Part 2: Application guide
    IEC 60099-8:2017 Surge arresters - Part 8: Metal-oxide surge arresters with external series gap (EGLA) for overhead transmission and distribution lines of a.c. systems above 1 kV
    EN 60071-2:1997 Insulation co-ordination - Part 2: Application guide
    IEC 60507:2013 Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems
    IEC 60071-1:2006+AMD1:2010 CSV Insulation co-ordination - Part 1: Definitions, principles and rules
    IEC TS 60815-1:2008 Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 1: Definitions, information and general principles
    EN 62271-200:2012/AC:2015 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 200: AC METAL-ENCLOSED SWITCHGEAR AND CONTROLGEAR FOR RATED VOLTAGES ABOVE 1 KV AND UP TO AND INCLUDING 52 KV (IEC 62271-200:2011)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective