Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN IEC 61281-1:2018

    Current The latest, up-to-date edition.

    FIBRE OPTIC COMMUNICATION SUBSYSTEMS - PART 1: GENERIC SPECIFICATION

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  10-04-2018

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    FOREWORD
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and acronyms
    5 Subsystem characteristics
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes for fibre optic communication subsystems (FOCSs).

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. EN 61281-1. For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (04/2018)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC TR 61282-12:2016 Fibre optic communication system design guides - Part 12: In-band optical signal-to-noise ratio (OSNR)
    IEC 61290-3-2:2008 Optical amplifiers - Test methods - Part 3-2: Noise figure parameters - Electrical spectrum analyzer method
    IEC TR 61282-5:2002 Fibre optic communication system design guides - Part 5: Accommodation and compensation of dispersion
    IEC 61290-10-4:2007 Optical amplifiers - Test methods - Part 10-4: Multichannel parameters - Interpolated source subtraction method using an optical spectrum analyzer
    IEC 61280-2-11:2006 Fibre optic communication subsystem test procedures - Part 2-11: Digital systems - Averaged Q-factor determination using amplitude histogram evaluation for optical signal quality monitoring
    IEC 61280-2-10:2005 Fibre optic communication subsystem test procedures - Part 2-10: Digital systems - Time-resolved chirp and alpha-factor measurement of laser transmitters
    IEC 61274-1:2011 Fibre optic interconnecting devices and passive components - Adaptors for fibre optic connectors - Part 1: Generic specification
    IEC 60050-731:1991 International Electrotechnical Vocabulary (IEV) - Part 731: Optical fibre communication
    IEC 61280-1-3:2010 Fibre optic communication subsystem test procedures - Part 1-3: General communication subsystems - Central wavelength and spectral width measurement
    IEC 61290-10-5:2014 Optical amplifiers - Test methods - Part 10-5: Multichannel parameters - Distributed Raman amplifier gain and noise figure
    IEC 60793-2-10:2017 Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres
    IEC 60793-1-41:2010 Optical fibres - Part 1-41: Measurement methods and test procedures - Bandwidth
    IEC 61290-3-3:2013 Optical amplifiers - Test methods - Part 3-3: Noise figure parameters - Signal power to total ASE power ratio
    IEC 61290-4-2:2011 Optical amplifiers - Test methods - Part 4-2: Gain transient parameters - Broadband source method
    IEC 61290-11-1:2008 Optical amplifiers - Test methods - Part 11-1: Polarization mode dispersion parameter - Jones matrix eigenanalysis (JME)
    IEC TR 61282-6:2003 Fibre optic communication system design guides - Part 6: Skew design in parallel optical interconnection systems
    IEC 60793-2:2015 Optical fibres - Part 2: Product specifications - General
    IEC 61291-2:2016 Optical amplifiers - Part 2: Single channel applications - Performance specification template
    IEC 61290-1-3:2015 Optical amplifiers - Test methods - Part 1-3: Power and gain parameters - Optical power meter method
    IEC 60050-151:2001 International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices
    IEC 61280-2-9:2009 Fibre optic communication subsystem test procedures - Part 2-9: Digital systems - Optical signal-to-noise ratio measurement for dense wavelength-division multiplexed systems
    IEC 60869-1:2012 Fibre optic interconnecting devices and passive components - Fibre optic passive power control devices - Part 1: Generic specification
    IEC 61290-6-1:1998 Optical fibre amplifiers - Basic specification - Part 6-1: Test methods for pump leakage parameters - Optical demultiplexer
    IEC 61290-1-1:2015 Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method
    IEC 60794-1-1:2015 Optical fibre cables - Part 1-1: Generic specification - General
    IEC 61291-4:2011 Optical amplifiers - Part 4: Multichannel applications - Performance specification template
    IEC TR 61282-15:2017 Fibre optic communication system design guides - Part 15: Cable plant and link - Testing multi-fibre optic cable plant terminated with MPO connectors
    IEC TR 61282-3:2006 Fibre optic communication system design guides - Part 3: Calculation of link polarization mode dispersion
    IEC 61280-1-1:2013 Fibre optic communication subsystem basic test procedures - Part 1-1: Test procedures for general communication subsystems - Transmitter output optical power measurement for single-mode optical fibre cable
    IEC 61280-2-3:2009 Fibre optic communication subsystem tets procedures - Part 2-3: Digital systems - Jitter and wander measurements
    IEC 61280-2-12:2014 Fibre optic communication subsystem test procedures - Part 2-12: Digital systems - Measuring eye diagrams and Q-factor using a software triggering technique for transmission signal quality assessment
    IEC 61290-5-3:2002 Basic specification for optical amplifier test methods - Part 5-3: Test methods for reflectance parameters - Reflectance tolerance test method using electrical spectrum analyzer
    IEC 61290-5-2:2003 Optical amplifiers - Test methods - Part 5-2: Reflectance parameters - Electrical spectrum analyser method
    IEC 61290-7-1:2007 Optical amplifiers - Test methods - Part 7-1: Out-of-band insertion losses - Filtered optical power meter method
    IEC TR 61931:1998 Fibre optic - Terminology
    IEC 60874-1:2011 Fibre optic interconnecting devices and passive components - Connectors for optical fibres and cables - Part 1: Generic specification
    IEC 61280-4-1:2009 Fibre-optic communication subsystem test procedures - Part 4-1: Installed cable plant - Multimode attenuation measurement
    IEC 61280-4-2:2014 Fibre-optic communication subsystem test procedures - Part 4-2: Installed cable plant - Single-mode attenuation and optical return loss measurement
    IEC 61280-2-2:2012 Fibre optic communication subsystem test procedures - Part 2-2: Digital systems - Optical eye pattern, waveform and extinction ratio measurement
    IEC 61703:2016 Mathematical expressions for reliability, availability, maintainability and maintenance support terms
    IEC 61290-3-1:2003 Optical amplifiers - Test methods - Part 3-1: Noise figure parameters - Optical spectrum analyzer method
    IEC TR 61282-7:2003 Fibre optic communication system design guides - Part 7: Statistical calculation of chromatic dispersion
    IEC 61290-10-2:2007 Optical amplifiers - Test methods - Part 10-2: Multichannel parameters - Pulse method using a gated optical spectrum analyzer
    IEC 61280-2-8:2003 Fibre optic communication subsystem test procedures - Digital systems - Part 2-8: Determination of low BER using Q-factor measurements
    IEC 61073-1:2009 Fibre optic interconnecting devices and passive components - Mechanical splices and fusion splice protectors for optical fibres and cables - Part 1: Generic specification
    IEC 61290-1:2014 Optical amplifiers - Test methods - Part 1: Power and gain parameters
    IEC 61291-1:2012 Optical amplifiers - Part 1: Generic specification
    IEC TR 61282-4:2013 Fibre optic communication system design guides - Part 4: Accommodation and utilization of non-linear effects
    IEC 60793-2-50:2015 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres
    IEC 61280-4-4:2017 Fibre optic communication subsystem test procedures - Part 4-4: Cable plants and links - Polarization mode dispersion measurement for installed links
    IEC 61290-4-1:2016 Optical amplifiers - Test methods - Part 4-1: Gain transient parameters - Two-wavelength method
    IEC 61290-11-2:2005 Optical amplifiers - Test methods - Part 11-2: Polarization mode dispersion parameter - Poincaré sphere analysis method
    IEC 61290-5-1:2006 Optical amplifiers - Test methods - Part 5-1: Reflectance parameters - Optical spectrum analyzer method
    IEC 61280-2-1:2010 Fibre optic communication subsystem test procedures - Part 2-1: Digital systems - Receiver sensitivity and overload measurement
    IEC 62614:2010 Fibre optics - Launch condition requirements for measuring multimode attenuation
    IEC 62149-1:2011 Fibre optic active components and devices - Performance standards - Part 1: General and guidance
    IEC 61290-1-2:2005 Optical amplifiers - Test methods - Part 1-2: Power and gain parameters - Electrical spectrum analyzer method
    IEC 61290-10-1:2009 Optical amplifiers - Test methods - Part 10-1: Multichannel parameters - Pulse method using an optical switch and optical spectrum analyzer
    IEC TS 62538:2008 Categorization of optical devices
    IEC 60875-1:2015 Fibre optic interconnecting devices and passive components - Non-wavelength-selective fibre optic branching devices - Part 1: Generic specification
    IEC TR 61282-8:2006 Fibre optic communication system design guides - Part 8: Calculating dispersion penalty from measured time-resolved chirp data
    IEC TR 61282-9:2016 Fibre optic communication system design guides - Part 9: Guidance on polarization mode dispersion measurements and theory
    IEC 61290-10-3:2002 Optical amplifiers - Test methods - Part 10-3: Multichannel parameters - Probe methods
    IEC 61280-1-4:2009 Fibre optic communication subsystem test procedures - Part 1-4: General communication subsystems - Light source encircled flux measurement method
    IEC 60876-1:2014 Fibre optic interconnecting devices and passive components - Fibre optic spatial switches - Part 1: Generic specification
    IEC TR 61282-13:2014 Fibre optic communication system design guides - Part 13: Guidance on in-service PMD and CD characterization of fibre optic links
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective