Skip to content
Please enter a keyword to search

  • IEC 60167:1964

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Methods of test for the determination of the insulation resistance of solid insulating materials

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  04-12-2015

    Language(s):  English - French, English, French

    Published date:  01-01-1964

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Contents
    Foreword
    Preface
    Clause
    Section One - General
    1. Scope
    2. Definitions
    3. Significance
    4. Test equipment
    Section Two - Electrodes
    5. Electrodes
    6. Taper pin electrodes (for flat plates; tubes
        and rods)
    7. Conducting paint electrodes (for flat plates;
        tubes and rods)
    8. Bar electrodes (for thin sheets and tapes)
    Section Three - Test Specimens
    9. Test specimens for taper pin electrodes
    10. Test specimens for conducting paint electrodes
    11. Test specimens for bar electrodes
    Section Four - Conditioning
    12. Conditions and procedures
    Section Five - Procedure
    13. Selection, preparation and measurement
    Section Six - Expression of Results
    14. Mathematical treatment
    Section Seven - Test Report
    15. Necessary information
    Section Eight - General Principles
    16. Selection of test pieces
    17. Cleaning test peices
    18. Mounting test specimens
    19. Reference

    Abstract - (Show below) - (Hide below)

    Describes procedures for rapidly determining the values of the insulation resistance of solid insulating materials in order to give a general indication of quality when great accuracy is not required.

    General Product Information - (Show below) - (Hide below)

    Development Note Also numbered as BS 903-C5(1983) and BS 2782-2.232(1992) (10/2005) Stability Date: 2015. (11/2012)
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 5735:1979 Test methods for determining electrolytic corrosion with electrical insulating materials
    12/30258455 DC : 0 FPREN 60065:2011+FPRAA - AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
    DIN 2874 E : 2002 Flanged steel pipes and flanged steel or cast iron pipes and fittings with PTFE or PFA linings – Technical delivery conditions
    BS 903-C5:1983 Methods of testing vulcanized rubber. Determination of insulation resistance
    BS 6233:1982 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
    04/30115503 DC : DRAFT JUN 2004 EN 14986 - DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES
    CEI EN 60544-2 : 2013 ELECTRICAL INSULATING MATERIALS - DETERMINATION OF THE EFFECTS OF IONIZING RADIATION ON INSULATING MATERIALS - PART 2: PROCEDURES FOR IRRADIATION AND TEST
    IEC 60893-2:2003 Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 2: Methods of test
    BS 5734-4:1980 Polyester moulding compounds for electrical and other purposes Specification for sheet moulding compounds for electrical purposes
    PD CLC/TR 60079-32-1:2015 Explosive atmospheres Electrostatic hazards, guidance
    BS 5734-2:1980 Polyester moulding compounds for electrical and other purposes Specification for dough moulding compounds for electrical purposes
    DIN EN 14598-3:2005-07 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements
    DIN EN 14598-2:2005-07 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements
    BS EN 14879-2:2006 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Coatings on metallic components
    IEC 62011-2:2004 Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of test
    BS EN ISO 15252-2:2000 Plastics. Epoxy powder moulding compounds (EP-PMCs) Preparation of test specimens and determination of properties
    BS EN 60893-2:2004 Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes Methods of test
    BS EN 14879-5:2007 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Linings on concrete components
    DIN EN 14879-4:2008-01 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 4: Linings on metallic components
    DIN EN 14879-2:2007-02 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 2: Coatings on metallic components
    EN 62011-2:2004 Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of test
    EN 60079-32-2:2015 Explosive atmospheres - Part 32-2: Electrostatics hazards - Tests
    EN 60893-2:2004 Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 2: Methods of test
    DIN 2875:2002-06 FLANGED STEEL PIPES AND FITTINGS WITH HARD OR SOFT RUBBER LININGS - TECHNICAL DELIVERY CONDITIONS
    EN 61212-2:2006 Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 2: Methods of test
    I.S. EN 60491:1996 SAFETY REQUIREMENTS FOR ELECTRONIC FLASH APPARATUS FOR PHOTOGRAPHIC PURPOSES
    BS EN 60079-32-2:2015 Explosive atmospheres Electrostatics hazards. Tests
    BS EN 62631-1:2011 Dielectric and resistive properties of solid insulating materials General
    BS 7825-3.2:1997 Calibration of rubber and plastics test equipment. Calibration schedules Electrical properties
    BS 771-1:1980 Phenolic moulding materials Specification for physical properties (excluding type L2 material)
    09/30200088 DC : 0 BS EN 14879-6 - ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 6: COMBINED LININGS WITH TILE AND BRICK LAYERS
    DIN EN 14879-6:2010-04 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 6: Combined linings with tile and brick layers
    BS EN 14879-6:2009 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Combined linings with tile and brick layers
    NF EN 14879-6 : 2010 ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 6: COMBINED LININGS WITH TILE AND BRICK LAYERS
    05/30136157 DC : DRAFT JUL 2005
    04/30109201 DC : DRAFT OCT 2004 EN 14879-2 - ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 2: COATINGS ON METALLIC COMPONENTS
    S.R. CLC/TR 60079-32-1:2015 EXPLOSIVE ATMOSPHERES - PART 32-1: ELECTROSTATIC HAZARDS - GUIDANCE
    PREN 14986 : DRAFT 2014 DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES
    BS IEC 60092-101:1994 Electrical installation in ships Definitions and general requirements
    UNE-IEC 60092-101:2010 Electrical installations in ships - Part 101: Definitions and general requirements
    I.S. EN 60544-4:2003 ELECTRICAL INSULATING MATERIALS - DETERMINATION OF THE EFFECTS OF IONIZING RADIATION - PART 4: CLASSIFICATION SYSTEM FOR SERVICE IN RADIATION ENVIRONMENTS
    I.S. EN 61204-7:2006 LOW VOLTAGE POWER SUPPLIES, D.C. OUTPUT - PART 7: SAFETY REQUIREMENTS
    DIN EN 14879-4 E : 2008 ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 4: LININGS ON METALLIC COMPONENTS
    DIN EN 14879-5 E : 2007 ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 5: LININGS ON CONCRETE COMPONENTS
    DIN EN ISO 14530-2:2000-08 Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14530-2:1999); German version EN ISO 14530-2:1999
    BS EN ISO 14528-2:2000 Plastics. Melamine-formaldehyde powder moulding compounds (MF-PMCs) Preparation of test specimens and determination of properties
    BS EN 14598-2:2005 Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Methods of test and general requirements
    EN 60065:2014/AC:2017-01 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016)
    I.S. EN 61212-2:2006 INSULATING MATERIALS - INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST
    I.S. EN 60893-2:2004 INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST
    I.S. EN 14986:2017 DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES
    DIN 28055-2:1991-02 CHEMICAL APPARATUS - SURFACE PROTECTION WITH ORGANIC LININGS FOR APPLICATION TO METALLIC COMPONENTS - PART 2: PROOF OF SUITABILITY AND TESTING
    BS 771:1992 Specification for phenolic moulding materials
    BS 5734-4:1990 Polyester moulding compounds for electrical and other purposes Specification for sheet moulding compounds for electrical purposes
    BS 1322:1992 Specification for aminoplastic moulding materials
    BS 5734-2:1990 Polyester moulding compounds for electrical and other purposes Specification for dough moulding compounds for electrical purposes
    VDE 0303-30 : 1993 METHODS OF TEST FOR INSULATING MATERIALS FOR ELECTRICAL PURPOSES; VOLUME RESISTIVITY AND SURFACE RESISTIVITY OF SOLID ELECTRICAL INSULATING MATERIALS
    12/30239877 DC : 0 BS EN 60065 ED 8.0 - AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
    14/30312008 DC : 0 BS EN 61340-2-3 ED. 2 - ELECTROSTATICS - PART 2-3: METHODS OF TEST FOR DETERMINING THE RESISTANCE AND RESISTIVITY OF SOLID MATERIALS USED TO AVOID ELECTROSTATIC CHARGE ACCUMULATION
    DIN 28055-2:2002-04 CHEMICAL APPARATUS - SURFACE PROTECTION WITH ORGANIC LININGS FOR APPLICATION TO METALLIC COMPONENTS - PART 2: PROOF OF SUITABILITY AND TESTING
    BS 5823:1979 Method of test for electrical resistance and resistivity of insulating materials at elevated temperatures
    ISO 2951:2012 Rubber, vulcanized or thermoplastic Determination of insulation resistance
    BS 2782-2.232(1983) : LATEST METHODS OF TESTING PLASTICS - ELECTRICAL PROPERTIES - DETERMINATION OF INSULATION RESISTANCE
    14/30294092 DC : 0 BS EN 14986 - DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES
    CEI EN 62011-2 : 2005 INSULATING MATERIALS - INDUSTRIAL, RIGID, MOULDED, LAMINATED TUBES AND RODS OF RECTANGULAR AND HEXAGONAL CROSS-SECTION, BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST
    DIN 2875 E : 2002 FLANGED STEEL PIPES AND FITTINGS WITH HARD OR SOFT RUBBER LININGS - TECHNICAL DELIVERY CONDITIONS
    CSA HGV 4.2 : 2013 HOSES FOR COMPRESSED HYDROGEN FUEL STATIONS, DISPENSERS AND VEHICLE FUEL SYSTEMS
    IEC 60092-101:1994+AMD1:1995 CSV Electrical installations in ships - Part 101: Definitions and general requirements
    I.S. EN 60544-2:2012 ELECTRICAL INSULATING MATERIALS - DETERMINATION OF THE EFFECTS OF IONIZING RADIATION ON INSULATING MATERIALS - PART 2: PROCEDURES FOR IRRADIATION AND TEST (IEC 60544-2:2012 (EQV))
    BS EN 60065 : 2014 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014, MODIFIED)
    I.S. EN 60079-32-2:2015 EXPLOSIVE ATMOSPHERES - PART 32-2: ELECTROSTATICS HAZARDS - TESTS
    DIN EN 14879-2 E : 2007 ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 2: COATINGS ON METALLIC COMPONENTS
    DIN EN 14879-3 E : 2007 ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 3: COATINGS ON CONCRETE COMPONENTS
    BS EN ISO 14923:2003 Thermal spraying. Characterization and testing of thermally sprayed coatings
    EN 13763-24 : 2002 EXPLOSIVES FOR CIVIL USES - DETONATORS AND RELAYS - PART 24: DETERMINATION OF THE ELECTRICAL NON-CONDUCTIVITY OF SHOCK TUBE
    EN ISO 14923:2003 Thermal spraying - Characterization and testing of thermally sprayed coatings (ISO 14923:2003)
    UNI EN 14879-6 : 2010 ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 6: COMBINED LININGS WITH TILE AND BRICK LAYERS
    VDE 0882 : 1996 SAFETY REQUIREMENTS FOR ELECTRONIC FLASH APPARATUS FOR PHOTOGRAPHIC PURPOSES
    DIN EN 14879-6 E : 2010 ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 6: COMBINED LININGS WITH TILE AND BRICK LAYERS
    BS EN 60544-4:2003 Electrical insulating materials. Determination of the effects of ionizing radiation Classification system for service in radiation environments
    06/30155368 DC : 0 PREN 14879-6 - ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 6: COMBINED LININGS WITH TILE AND BRICK LAYERS
    UNE-EN 60065:2015 Audio, video and similar electronic apparatus - Safety requirements
    CSA C22.2 No. 60065 : 2016 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
    I.S. EN 14879-6:2009 ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 6: COMBINED LININGS WITH TILE AND BRICK LAYERS
    BS PD IEC TS 60079-32-1 : 2013 EXPLOSIVE ATMOSPHERES - PART 32-1: ELECTROSTATIC HAZARDS, GUIDANCE
    I.S. EN 60065:2014 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
    02/124520 DC : DRAFT DEC 2002 EN 14598-3 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 3: SPECIFIC REQUIREMENTS
    BS EN ISO 14529-2:2000 Plastics. Melamine/phenolic powder moulding compounds (MP-PMCs) Preparation of test specimens and determination of properties
    BS EN 14986:2007 Design of fans working in potentially explosive atmospheres
    ISO 14528-2:1999 Plastics Melamine-formaldehyde powder moulding compounds (MF-PMCs) Part 2: Preparation of test specimens and determination of properties
    BS EN 14879-4:2007 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Linings on metallic components
    IEC 62631-1:2011 Dielectric and resistive properties of solid insulating materials - Part 1: General
    UNE-EN 14986:2017 Design of fans working in potentially explosive atmospheres
    IEC 60544-2:2012 Electrical insulating materials - Determination of the effects of ionizing radiation on insulating materials - Part 2: Procedures for irradiation and test
    ISO 14530-2:1999 Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 2: Preparation of test specimens and determination of properties
    BS EN 14879-3:2006 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Coatings on concrete components
    IEC 61212-2:2006 Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 2: Methods of test
    ISO 14923:2003 Thermal spraying Characterization and testing of thermally sprayed coatings
    ISO 14529-2:1999 Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 2: Preparation of test specimens and determination of properties
    BS EN ISO 14527-2:2000 Preparation of test specimens and determination of properties
    BS EN 14598-3:2005 Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Specific requirements
    ISO 14526-2:1999 Plastics Phenolic powder moulding compounds (PF-PMCs) Part 2: Preparation of test specimens and determination of properties
    BS EN 13763-24:2002 Explosives for civil uses. Detonators and relays Determination of the electrical non-conductivity of shock tube
    BS EN 61204-7:2006 Live working. Conductive clothing Safety requirements
    BS EN ISO 14526-2:2000 Plastics. Phenolic powder moulding compounds (PF-PMCs) Preparation of test specimens and determination of properties
    EN 14879-3:2006 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 3: Coatings on concrete components
    EN 14879-2:2006 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 2: Coatings on metallic components
    EN 14879-5:2007 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components
    EN 14986:2017 Design of fans working in potentially explosive atmospheres
    EN ISO 15252-2 : 1999 PLASTICS - EPOXY POWDER MOULDING COMPOUNDS (EP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN 14598-2:2005/AC:2006 REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS
    EN ISO 14529-2 : 1999 PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN ISO 14530-2 : 1999 PLASTICS - UNSATURATED-POLYESTER POWDER MOULDING COMPOUNDS (UP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN 14879-6:2009 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 6: Combined linings with tile and brick layers
    EN ISO 14528-2 : 1999 PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN 14598-3:2005 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements
    EN ISO 14527-2 : 1999 PLASTICS - UREA-FORMALDEHYDE AND UREA/MELAMINE-FORMALDEHYDE POWDER MOULDING COMPOUNDS (UF- AND UF/MF-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN 14879-4:2007 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 4: Linings on metallic components
    NF EN 62631-1 : 2011 DIELECTRIC AND RESISTIVE PROPERTIES OF SOLID INSULATING MATERIALS - PART 1: GENERAL
    11/30212452 DC : 0 BS ISO 2951 - VULCANIZED RUBBER - DETERMINATION OF INSULATION RESISTANCE
    I.S. EN 62011-2:2004 INSULATING MATERIALS - INDUSTRIAL, RIGID, MOULDED, LAMINATED TUBES AND RODS OF RECTANGULAR AND HEXAGONAL CROSS-SECTION, BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES, - PART 2: METHODS OF TEST
    CEI EN 60893-2 : 2005 INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST
    BS EN 60544-2:2012 Electrical insulating materials. Determination of the effects of ionizing radiation on insulating materials Procedures for irradiation and test
    BS EN 62011-2:2004 Insulating materials. Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes Methods of test
    04/30123574 DC : DRAFT OCT 2004 EN 14879-3 - ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 3: COATINGS ON CONCRETE COMPONENTS
    BS 4145:1967 Specification for glass mica boards for electrical purposes
    BS IEC 61340-5.1 : 1998 AMD 13198 ELECTROSTATICS - PART 5-1: PROTECTION OF ELECTRONIC DEVICES FROM ELECTROSTATIC PHENOMENA - GENERAL REQUIREMENTS
    IEC 60544-4:2003 Electrical insulating materials - Determination of the effects of ionizing radiation - Part 4: Classification system for service in radiation environments
    07/30174056 DC : 0 BS EN 60065 - AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
    CEI EN 60544-4 : 2005 ELECTRICAL INSULATING MATERIALS - DETERMINATION OF THE EFFECTS OF IONIZING RADIATION - PART 4: CLASSIFICATION SYSTEM FOR SERVICE IN RADIATION ENVIRONMENTS
    UNE-EN 62631-1:2012 Dielectric and resistive properties of solid insulating materials - Part 1: General
    I.S. EN 62631-1:2011 DIELECTRIC AND RESISTIVE PROPERTIES OF SOLID INSULATING MATERIALS - PART 1: GENERAL
    NF EN 60065 : 2015 AMD 11 2018 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
    CLC/TR 60079-32-1:2015 Explosive atmospheres - Part 32-1: Electrostatic Hazards - Guidance
    UNE-EN 60079-32-2:2016 Explosive atmospheres - Part 32-2: Electrostatics hazards - Tests
    ISO 15252-2:1999 Plastics Epoxy powder moulding compounds (EP-PMCs) Part 2: Preparation of test specimens and determination of properties
    ISO 14527-2:1999 Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 2: Preparation of test specimens and determination of properties
    02/124519 DC : DRAFT DEC 2002 EN 14598-2 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS
    BS EN 61212-2:2006 Insulating materials. Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Methods of test
    BS EN ISO 14530-2:2000 Plastics. Unsaturated-polyester powder moulding compounds (UP-PMCs) Preparation of test specimens and determination of properties
    DIN 2874:2002-06 Flanged steel pipes and flanged steel or cast iron pipes and fittings with PTFE or PFA linings – Technical delivery conditions
    DIN EN 14879-3:2007-02 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 3: Coatings on concrete components
    EN 60491 : 1995 SAFETY REQUIREMENTS FOR ELECTRONIC FLASH APPARATUS FOR PHOTOGRAPHIC PURPOSES
    EN 60544-4:2003 Electrical insulating materials - Determination of the effects of ionizing radiation - Part 4: Classification system for service in radiation environments
    DIN EN ISO 14923:2003-10 THERMAL SPRAYING - CHARACTERIZATION AND TESTING OF THERMALLY SPRAYED COATINGS
    EN 60544-2:2012 Electrical insulating materials - Determination of the effects of ionizing radiation on insulating materials - Part 2: Procedures for irradiation and test
    DIN EN 14879-5:2007-10 Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components
    EN 62631-1 : 2011 DIELECTRIC AND RESISTIVE PROPERTIES OF SOLID INSULATING MATERIALS - PART 1: GENERAL (IEC 62631-1:2011)
    BS 415(1998) : 1998 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective