Skip to content
Please enter a keyword to search

  • IEC 60297-5-100:2001

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-100: Subracks and associated plug-in units - Design overview

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  17-08-2004

    Language(s):  English, Spanish, Castilian

    Published date:  24-01-2001

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    Clause
    1 Scope and object
    2 Normative references
    3 Definitions
    4 Extended features added to IEC 60297-3 and IEC
      60297-4
    5 General equipment arrangement
    6 Detail equipment arrangement
    7 Subracks and associated plug-in units - Extended
      features - Summary

    Abstract - (Show below) - (Hide below)

    Gives a design overview of the related detail standards which will ensure dimensional interchangeability of subracks and associated plug-in units. The extended features contained in this standard may be referred to and/or implemented independently. Refer also to IEC 61587-1 and IEC/TS 61587-3.

    General Product Information - (Show below) - (Hide below)

    Development Note Also numbered as BS EN 60297-5.100. (06/2001)
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    EN 60297-5-101:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-101: Subracks and associated plug-in units - Injector/extractor handle
    BS EN 60297-5-101:2001 Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Injector/extractor handle
    98/231544 DC : DRAFT JULY 1998
    IEC 60297-5-105:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-105: Subracks and associated plug-in units - Alignment and/or earth pin
    IEC 60297-5-103:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-103: Subracks and associated plug-in units - Electrostatic discharge protection
    BS EN 60297-5-102:2001 Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Electromagnetic shielding provision
    BS EN 60297-5-104:2001 Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Keying
    IEC 60297-5-107:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-107: Subracks and associated plug-in units - Rear-mounted plug-in units
    IEC 60297-5-102:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-102: Subracks and associated plug-in units - Electromagnetic shielding provision
    BS EN 60297-5-103:2001 Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Electrostatic discharge protection
    BS EN 60297-5-105:2001 Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Alignments and/or earth pin
    BS EN 60297-5-107:2001 Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Rear mounted plug-in units
    IEC 60297-5-101:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-101: Subracks and associated plug-in units - Injector/extractor handle
    IEC 60297-5-104:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-104: Subracks and associated plug-in units - Keying
    EN 60297-5-103:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-103: Subracks and associated plug-in units - Electrostatic discharge protection
    EN 60297-5-105:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-105: Subracks and associated plug-in units - Alignment and/or earth pin
    EN 60297-5-104:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-104: Subracks and associated plug-in units - Keying
    EN 60297-5-102:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-102: Subracks and associated plug-in units - Electromagnetic shielding provision
    EN 60297-5-107:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-107: Subracks and associated plug-in units - Rear mounted plug-in units

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60297-5-102:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-102: Subracks and associated plug-in units - Electromagnetic shielding provision
    IEC 61076-4-113:2002 Connectors for electronic equipment - Printed board connectors - Part 4-113: Detail specification for two-part connectors having 5 rows with a grid of 2,54 mm for printed boards and backplanes in bus applications
    IEC 60297-5-107:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-107: Subracks and associated plug-in units - Rear-mounted plug-in units
    IEC 60297-5-105:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-105: Subracks and associated plug-in units - Alignment and/or earth pin
    IEC 60297-1:1986 Dimensions of mechanical structures of the 482.6 mm (19 in) series. Part 1: Panels and racks
    IEC 60297-5-103:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-103: Subracks and associated plug-in units - Electrostatic discharge protection
    IEC 60297-5-101:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-101: Subracks and associated plug-in units - Injector/extractor handle
    IEC 61587-1:2016 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
    IEC 60297-4:1995+AMD1:1999 CSV Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 4: Subracks and associated plug-in units - Additional dimensions
    IEC TS 61587-3:1999 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic shielding performance tests for cabinets, racks and subracks
    IEC 60297-5-104:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-104: Subracks and associated plug-in units - Keying
    IEC 60603-2:1995 Connectors for frequencies below 3 MHz for use with printed boards - Part 2: Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features
    IEC 61076-4-101:2001 Connectors for electronic equipment - Part 4-101: Printed board connectors with assessed quality - Detail specification for two-part connector modules, having a basic grid of 2,0 mm for printed boards and backplanes in accordance with IEC 60917
    IEC 60917-1:1998+AMD1:2000 CSV Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective